2. TEL:886-2-2695-0789 FAX:886-2-2695-1896
11F., No.44, Lane 156, Fude 2nd Rd., Sijhih City, Taipei County 221, Taiwan
2
SMD Chip Common Mode Choke
Shape and Size: (Unit:mm)
TYPE A B C D E
CMA05 2.05±0.2 1.25±0.2 1.20±0.2 0.5 0.58
Applications
USB line for personal computers and peripheral,
IEEE 1394 line for personal computers, DVC.
LVDS, panel line for liquid display panels, graph
card etc.
Features
Miniature SMD type common mode filter for fully
automated assembly.
Wide Impedance range (30Ω ~ 2200Ω ) for noise
suppression.
Excellent Solderability.
Operating temperature from -45℃ to 85℃.
Test equipments:
L&Q:HP4285A Precision LCR meter.
SRF:HP4291B RF Impedance Analyzer
DCR: Milli-ohm meter
Temperature :25±3℃;<80%RH
Ordering Information:
CMA 05 M T 900
1 2 3 4 5
1. Type: SMD Common Mode
Chok
2. Dimensions(mm): 05=2.0X1.25X1.2
3. Tolerance: M=±20% N=±30%
4. Packaging style: Taping Reel
Codes Inductance
900 90Ω
121 120Ω
102 1000Ω
5. Impedance:
222 2200Ω
4. TEL:886-2-2695-0789 FAX:886-2-2695-1896
11F., No.44, Lane 156, Fude 2nd Rd., Sijhih City, Taipei County 221, Taiwan
4
Tape and Reel speifiations
Codes A B D E F H I P P0 P2 Packaging
CMA05 8 1.5 2.25 3.5 1.75 1.45 0.24 4 4 2 2000
The force for tearing off cover tape is 10 to 100 grams in the arrow direction.
Reel Dimensions
TYPE A B C D
CMA05 178 60 12 1.5
6. TEL:886-2-2695-0789 FAX:886-2-2695-1896
11F., No.44, Lane 156, Fude 2nd Rd., Sijhih City, Taipei County 221, Taiwan
6
Electrical Performance Test
No Item Specification Test Method
1-1-1 Temperature Cycle Appearance: No Damage One cycle:
Impedance: within±20% of Step Temperature (℃)
Time
(min)
1 -25±3 30
2 25±2 3
3 85±3 30
4 25±2 3
initial value
Total: 5 cycles
Measured After Exposure in The Room Condition For 1hrs
1-1-2 Humidity Resistance Temperature: 40±2℃
Relative Humidity: 90 ~ 95%
Time: 100hrs
Measured After Exposure In The Room Condition For 1hrs
1-1-3 High Temperature
Resistance
Temperature: 85±3℃
Time: 50Hrs
Measured After Exposure In The Room Condition For 1Hrs
1-1-4 Low Temperature Resistance Temperature: -25±3℃
Time: 50Hrs
Measured After Exposure In The Room Condition For 1Hrs
1-1-5 High Temperature Load
Life
There should be no
evidence
Temperature: 85±3℃
of short or open circle Load: Allowed DC Current
Time: 500Hrs
1-1-6 Humidity Load Life Temperature: 40±2℃
Relative Humidity: 90~95%
Load: Allowed DC Current
Time: 500Hrs
1-2.Mechanical Performance
No Item Specification Test Method
1-2-1 Resistance To Soldering
Heat
Appearance: No
Damage
1. The device should be reflow soldered on PCB
(peak 260℃±5℃ for 10 seconds)
2. Solder Composition: Sn/Ag3.0/Cu0.5
3. Test time: 6 minutes
1-2-2 Solder ability The Electrodes Shall
Be
1. Pre-Heating: 150℃,1min.
At Least 90% Covered 2. Solder Composition: Sn/Ag3.0/Cu0.5
with New Solder
Coating
3. Solder Temperature: 245±5℃.
4. Immersion Time: 4±1 sec.
1-2-3 Commponent Adhesion 2 Lbs The device should be reflow soldered (245±5℃ For
(Push Test) 10 seconds) to a tinned copper substrate. A force
guauge
should be applied to the side of the component.
The device must withstand a minimum force of 2
pounds
without a failure of the termination attached to
component
8. Sample Description :
Style/Item No. :
Sample Receiving Date :
Testing Period :
===========================================================================================
Test Result(s) :
Test Report No. : CE/2008/92572F Date : 2009/06/11 Page : 1 of 7
2008/09/10 TO 2008/09/16
Please refer to next page(s).
HT-TECH CORPORATION
11F, NO. 44, LANE 156, FUDE 2ND RD., SIJHIH CITY, TAIPEI COUNTY 221,
TAIWAN
The following sample(s) was/were submitted and identified by/on behalf of the client as :
*CE/2008/92572F*
COMMON MODE CHOKE
CMA SERIES
2008/09/10
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司 Chemical-Taipei 33 WuChyuan Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五權路33號 t + 886 (02)2299 3279 f + 886 (02)2299 3237 www.sgs.com
Member of the SGS Group (SGS SA)
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This test report cannot be reproduced, except in full, without prior written permission of the Company.
除非另有說明,此報告結果僅對測試之樣品負責。本報告未經本公司書面許可,不可部分複製。
This Test Report is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention
is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this Test Report is advised that information contained hereon reflects the Company’s findings
at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction
from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and
offenders may be prosecuted to the fullest extent of the law.
9. Test Result(s)
PART NAME NO.1 :
Result
No.1
Cadmium (Cd) mg/kg With reference to IEC 62321:
2008 and performed by ICP-
AES.
2 n.d.
Lead (Pb) mg/kg With reference to IEC 62321:
2008 and performed by ICP-
AES.
2 20
Mercury (Hg) mg/kg With reference to IEC 62321:
2008 and performed by ICP-
AES.
2 n.d.
Hexavalent Chromium Cr(VI) by
alkaline extraction
mg/kg With reference to IEC 62321:
2008 and performed by UV-VIS.
2 n.d.
Perfluorooctane sulfonates
(PFOS)
PFOS – Acid
PFOS – Metal Salt
PFOS – Amide
mg/kg With reference to US EPA
3540C: 1996 method for PFOS
Content. Analysis was
performed by LC/MS.
10 n.d.
Sum of PBBs - n.d.
Monobromobiphenyl 5 n.d.
Dibromobiphenyl 5 n.d.
Tribromobiphenyl 5 n.d.
Tetrabromobiphenyl 5 n.d.
Pentabromobiphenyl 5 n.d.
Hexabromobiphenyl 5 n.d.
Heptabromobiphenyl 5 n.d.
Octabromobiphenyl 5 n.d.
Nonabromobiphenyl 5 n.d.
Decabromobiphenyl 5 n.d.
COMMON MODE CHOKE
MDL
With reference to IEC 62321:
2008 and performed by GC/MS.
Test Item (s): Unit Method
mg/kg
Test Report No. : CE/2008/92572F Date : 2009/06/11 Page : 2 of 7
HT-TECH CORPORATION *CE/2008/92572F*
11F, NO. 44, LANE 156, FUDE 2ND RD., SIJHIH CITY, TAIPEI COUNTY 221,
TAIWAN
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司 Chemical-Taipei 33 WuChyuan Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五權路33號 t + 886 (02)2299 3279 f + 886 (02)2299 3237 www.sgs.com
Member of the SGS Group (SGS SA)
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This test report cannot be reproduced, except in full, without prior written permission of the Company.
除非另有說明,此報告結果僅對測試之樣品負責。本報告未經本公司書面許可,不可部分複製。
This Test Report is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention
is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this Test Report is advised that information contained hereon reflects the Company’s findings
at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction
from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and
offenders may be prosecuted to the fullest extent of the law.
10. Result
No.1
Sum of PBDEs - n.d.
Monobromodiphenyl ether 5 n.d.
Dibromodiphenyl ether 5 n.d.
Tribromodiphenyl ether 5 n.d.
Tetrabromodiphenyl ether 5 n.d.
Pentabromodiphenyl ether 5 n.d.
Hexabromodiphenyl ether 5 n.d.
Heptabromodiphenyl ether 5 n.d.
Octabromodiphenyl ether 5 n.d.
Nonabromodiphenyl ether 5 n.d.
Decabromodiphenyl ether 5 n.d.
Reference Information : Directive 2006/122/EC
(1) May not be placed on the market or used as a substance or constituent of preparations in a
concentration equal to or higher than 0.005 % by mass.
Note: 1. mg/kg = ppm
2. n.d. = Not Detected
4. " - " = Not Regulated
MDL
11F, NO. 44, LANE 156, FUDE 2ND RD., SIJHIH CITY, TAIPEI COUNTY 221,
TAIWAN
3. MDL = Method Detection Limit
(2) May not be placed on the market in semi-finished products or articles, or parts thereof, if the
concentration of PFOS is equal to or higher than 0.1 % by mass calculated with reference to the
mass of structurally or microstructurally distinct parts that contain PFOS or, for textiles or other
coated materials, if the amount of PFOS is equal to or higher than 1µg/m2
of the coated material.
mg/kg
With reference to IEC 62321:
2008 and performed by GC/MS.
Test Item (s): Unit Method
Test Report No. : CE/2008/92572F Date : 2009/06/11 Page : 3 of 7
HT-TECH CORPORATION *CE/2008/92572F*
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司 Chemical-Taipei 33 WuChyuan Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五權路33號 t + 886 (02)2299 3279 f + 886 (02)2299 3237 www.sgs.com
Member of the SGS Group (SGS SA)
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This test report cannot be reproduced, except in full, without prior written permission of the Company.
除非另有說明,此報告結果僅對測試之樣品負責。本報告未經本公司書面許可,不可部分複製。
This Test Report is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention
is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this Test Report is advised that information contained hereon reflects the Company’s findings
at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction
from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and
offenders may be prosecuted to the fullest extent of the law.
11. Test Report No. : CE/2008/92572F Date : 2009/06/11 Page : 4 of 7
HT-TECH CORPORATION *CE/2008/92572F*
11F, NO. 44, LANE 156, FUDE 2ND RD., SIJHIH CITY, TAIPEI COUNTY 221,
TAIWAN
1) These samples were dissolved totally by pre-conditioning method according to below flow chart.
(Cr
6+
test method excluded)
2) Name of the person who made measurement: Climbgreat Yang
3) Name of the person in charge of measurement: Troy Chang
Cr6+
Sample Material Digestion Acid
Steel, copper, aluminum, solder Aqua regia, HNO3, HCl, HF, H2O2
Glass HNO3/HF
Gold, platinum, palladium, ceramic Aqua regia
Silver HNO3
Plastic H2SO4, H2O2, HNO3, HCl
Others Any acid to total digestion
Pb、Cd
Solution
ICP-AES
Acid digestion by suitable acid
depended on different sample
material (as below table)
Filtration
Residue
1) Alkali Fusion
2) HCl to dissolve
Sample Measurement
Cutting / Preparation
Microwave digestion with
HNO3/HCl/HF
Heat to appropriate
temperature to extract
Cool, filter digestate
through filter
Add diphenyl-carbazide for
color development
measure the absorbance
at 540 nm by UV-VIS
Add appropriate amount of
digestion reagent
Hg
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司 Chemical-Taipei 33 WuChyuan Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五權路33號 t + 886 (02)2299 3279 f + 886 (02)2299 3237 www.sgs.com
Member of the SGS Group (SGS SA)
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This test report cannot be reproduced, except in full, without prior written permission of the Company.
除非另有說明,此報告結果僅對測試之樣品負責。本報告未經本公司書面許可,不可部分複製。
This Test Report is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention
is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this Test Report is advised that information contained hereon reflects the Company’s findings
at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction
from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and
offenders may be prosecuted to the fullest extent of the law.
12. Test Report No. : CE/2008/92572F Date : 2009/06/11 Page : 5 of 7
HT-TECH CORPORATION *CE/2008/92572F*
11F, NO. 44, LANE 156, FUDE 2ND RD., SIJHIH CITY, TAIPEI COUNTY 221,
TAIWAN
Analytical flow chart of PFOA/PFOS content
Sample pretreatment
Sample extraction by Soxhlet extraction
(Reference method US EPA 3540C)
Concentrate/Dilute Extracted solution
Analysis was performed by LC/MS
Data
1) Name of the person who made measurement: Carrie Liu
2) Name of the person in charge of measurement: Shinjyh Chen
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司 Chemical-Taipei 33 WuChyuan Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五權路33號 t + 886 (02)2299 3279 f + 886 (02)2299 3237 www.sgs.com
Member of the SGS Group (SGS SA)
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This test report cannot be reproduced, except in full, without prior written permission of the Company.
除非另有說明,此報告結果僅對測試之樣品負責。本報告未經本公司書面許可,不可部分複製。
This Test Report is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention
is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this Test Report is advised that information contained hereon reflects the Company’s findings
at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction
from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and
offenders may be prosecuted to the fullest extent of the law.
13. Test Report No. : CE/2008/92572F Date : 2009/06/11 Page : 6 of 7
HT-TECH CORPORATION *CE/2008/92572F*
11F, NO. 44, LANE 156, FUDE 2ND RD., SIJHIH CITY, TAIPEI COUNTY 221,
TAIWAN
PBB/PBDE analytical FLOW CHART
First testing process
Optional screen process
Confirmation process
Sample
Screen analysis
Issue Report
Sample pretreatment
Sample extraction/
Soxhlet method
Concentrate/Dilute
Extracted solution
Analysis by GC/MS
Filter
1) Name of the person who made measurement: Roman Wong
2) Name of the person in charge of measurement: Shinjyh Chen
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司 Chemical-Taipei 33 WuChyuan Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五權路33號 t + 886 (02)2299 3279 f + 886 (02)2299 3237 www.sgs.com
Member of the SGS Group (SGS SA)
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This test report cannot be reproduced, except in full, without prior written permission of the Company.
除非另有說明,此報告結果僅對測試之樣品負責。本報告未經本公司書面許可,不可部分複製。
This Test Report is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention
is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this Test Report is advised that information contained hereon reflects the Company’s findings
at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction
from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and
offenders may be prosecuted to the fullest extent of the law.
14. ** End of Report **
Test Report No. : CE/2008/92572F Date : 2009/06/11 Page : 7 of 7
HT-TECH CORPORATION *CE/2008/92572F*
11F, NO. 44, LANE 156, FUDE 2ND RD., SIJHIH CITY, TAIPEI COUNTY 221,
TAIWAN
SGS Taiwan Ltd.
台灣檢驗科技股份有限公司 Chemical-Taipei 33 WuChyuan Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五權路33號 t + 886 (02)2299 3279 f + 886 (02)2299 3237 www.sgs.com
Member of the SGS Group (SGS SA)
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This test report cannot be reproduced, except in full, without prior written permission of the Company.
除非另有說明,此報告結果僅對測試之樣品負責。本報告未經本公司書面許可,不可部分複製。
This Test Report is issued by the Company under its General Conditions of Service printed overleaf or available on request and accessible at http://www.sgs.com/terms_and_conditions.htm. Attention
is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this Test Report is advised that information contained hereon reflects the Company’s findings
at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction
from exercising all their rights and obligations under the transaction documents. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and
offenders may be prosecuted to the fullest extent of the law.