The document provides instructions for removing and installing engine components such as valve guides, valve seat inserts, the engine oil filter base, and oil cooler on Caterpillar 336D2 and 336D2L excavator models powered by a C9 engine. The procedures include using various tools to remove and install parts, ensuring parts are clean, and proper assembly of spring-loaded components.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...pfiskdmjekm
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair. Tools required are listed for each procedure.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...fjjskekdmmem
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair work. Detailed illustrations accompany the step-by-step instructions for each procedure.
The document provides instructions for removing and installing engine oil filter bases, oil coolers, valve guides, and valve seat inserts on Caterpillar 336D2 and 336D2L excavators. The procedures include using various tools to disconnect hoses, remove bolts, and extract or install components. Technicians are advised to keep parts clean and contain fluids during the repair process.
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...pfiskdmjekm
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair. Tools required are listed for each procedure.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...fjjskekdmmem
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair work. Detailed illustrations accompany the step-by-step instructions for each procedure.
The document provides instructions for removing and installing engine oil filter bases, oil coolers, valve guides, and valve seat inserts on Caterpillar 336D2 and 336D2L excavators. The procedures include using various tools to disconnect hoses, remove bolts, and extract or install components. Technicians are advised to keep parts clean and contain fluids during the repair process.
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...8ufjsekddm8u
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...8ufjsekddm8u
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, bolts securing the housing, and oil seal from the housing. It then describes how to install a new oil seal, gasket, and reattach the housing using bolts, and reinstall the flywheel and electric starting motor.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...8ufjsekddm8u
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and torque wrench to reinstall these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
Caterpillar Cat 323D L Excavator (Prefix NZF) Service Repair Manual (NZF00001...8ufjsekddm8u
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using specialized tools to compress the valve springs and position the pistons at top dead center. Springs are removed in pairs from specific cylinders and must be replaced in the same order. Installation requires lubricating seals, compressing springs with a tool to insert retainers and keepers, and checking valve clearance after installation is complete. Safety precautions are outlined to prevent injury from released spring forces.
Caterpillar Cat 323D L Excavator (Prefix BYM) Service Repair Manual (BYM00001...8ufjsekddm8u
1) The document provides instructions for removing and installing various engine components on a Caterpillar 323D L Excavator, including valve seat inserts, the engine oil cooler, and the engine oil relief valve.
2) The procedures include a list of required tools and step-by-step instructions describing how to remove, disassemble, and assemble each component while taking appropriate safety precautions.
3) Technicians are advised to keep all parts clean and free of contaminants to prevent damage and wear.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...8ufjsekddm8u
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like the spring, arms, bracket and washer onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, the pushrods and rocker shaft are positioned and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual (JLG00001...8ufjsekddm8u
This service repair manual provides instructions for removing and installing valve seat inserts, removing and disassembling the engine oil cooler, and assembling the engine oil cooler for a Caterpillar C6.4 engine powering a 323D L excavator. The document lists required tools and safety notices, and includes illustrations of the removal, disassembly, and assembly procedures.
Caterpillar Cat 323D L Excavator (Prefix LFL) Service Repair Manual (LFL00001...8ufjsekddm8u
1) The document provides instructions for removing and installing the fuel injection pump on a Caterpillar C6.4 engine.
2) To remove the pump, various hoses, tubes, brackets and electrical connections must be disconnected and markings made for installation. Bolts then need to be removed to access the pump.
3) Installation involves reversing the removal process, ensuring cleanliness, replacing washers, and torquing all connections to the specified values.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...8ufjsekddm8u
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are required to lift the housing and remove the oil seal. When installing, a new gasket and oil seal are used and the housing is bolted back in place before reinstalling the flywheel and starting motor.
This document provides installation instructions for a rear power take-off (RPTO) on a 323 excavator with a C7.1 engine. It describes 20 steps to install the RPTO, including installing sleeve bearings, gears, idler hubs, adapters and bolts. Precautions are given to keep components clean and ensure proper alignment of parts. Tools required include drivers and sockets.
This document provides instructions for disassembling and assembling the travel motor of a 323D and 323D L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, and shaft assembly. It then describes 13 steps to reassemble the travel motor by installing components like the shaft assembly, cam plate, barrel assembly, and head in the reverse order of disassembly. Precautions are given to clean parts thoroughly, mark components for reinstallation, and ensure proper alignment of parts.
1) The document provides instructions for removing and installing a flywheel from a C7.1 engine that powers a 323 excavator.
2) To remove the flywheel, bolts must first be removed and guide studs installed to support the flywheel. Lifting equipment is then used to lift the flywheel off while inspecting components for wear or damage.
3) Flywheel installation requires cleaning and lifting the flywheel into place using guide studs. Bolts are tightened to the specified torque and the flywheel is inspected for proper runout.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...8ufjsekddm8u
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...8ufjsekddm8u
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...8ufjsekddm8u
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...8ufjsekddm8u
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, bolts securing the housing, and oil seal from the housing. It then describes how to install a new oil seal, gasket, and reattach the housing using bolts, and reinstall the flywheel and electric starting motor.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...8ufjsekddm8u
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and torque wrench to reinstall these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
Caterpillar Cat 323D L Excavator (Prefix NZF) Service Repair Manual (NZF00001...8ufjsekddm8u
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using specialized tools to compress the valve springs and position the pistons at top dead center. Springs are removed in pairs from specific cylinders and must be replaced in the same order. Installation requires lubricating seals, compressing springs with a tool to insert retainers and keepers, and checking valve clearance after installation is complete. Safety precautions are outlined to prevent injury from released spring forces.
Caterpillar Cat 323D L Excavator (Prefix BYM) Service Repair Manual (BYM00001...8ufjsekddm8u
1) The document provides instructions for removing and installing various engine components on a Caterpillar 323D L Excavator, including valve seat inserts, the engine oil cooler, and the engine oil relief valve.
2) The procedures include a list of required tools and step-by-step instructions describing how to remove, disassemble, and assemble each component while taking appropriate safety precautions.
3) Technicians are advised to keep all parts clean and free of contaminants to prevent damage and wear.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...8ufjsekddm8u
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like the spring, arms, bracket and washer onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, the pushrods and rocker shaft are positioned and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual (JLG00001...8ufjsekddm8u
This service repair manual provides instructions for removing and installing valve seat inserts, removing and disassembling the engine oil cooler, and assembling the engine oil cooler for a Caterpillar C6.4 engine powering a 323D L excavator. The document lists required tools and safety notices, and includes illustrations of the removal, disassembly, and assembly procedures.
Caterpillar Cat 323D L Excavator (Prefix LFL) Service Repair Manual (LFL00001...8ufjsekddm8u
1) The document provides instructions for removing and installing the fuel injection pump on a Caterpillar C6.4 engine.
2) To remove the pump, various hoses, tubes, brackets and electrical connections must be disconnected and markings made for installation. Bolts then need to be removed to access the pump.
3) Installation involves reversing the removal process, ensuring cleanliness, replacing washers, and torquing all connections to the specified values.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...8ufjsekddm8u
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are required to lift the housing and remove the oil seal. When installing, a new gasket and oil seal are used and the housing is bolted back in place before reinstalling the flywheel and starting motor.
This document provides installation instructions for a rear power take-off (RPTO) on a 323 excavator with a C7.1 engine. It describes 20 steps to install the RPTO, including installing sleeve bearings, gears, idler hubs, adapters and bolts. Precautions are given to keep components clean and ensure proper alignment of parts. Tools required include drivers and sockets.
This document provides instructions for disassembling and assembling the travel motor of a 323D and 323D L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, and shaft assembly. It then describes 13 steps to reassemble the travel motor by installing components like the shaft assembly, cam plate, barrel assembly, and head in the reverse order of disassembly. Precautions are given to clean parts thoroughly, mark components for reinstallation, and ensure proper alignment of parts.
1) The document provides instructions for removing and installing a flywheel from a C7.1 engine that powers a 323 excavator.
2) To remove the flywheel, bolts must first be removed and guide studs installed to support the flywheel. Lifting equipment is then used to lift the flywheel off while inspecting components for wear or damage.
3) Flywheel installation requires cleaning and lifting the flywheel into place using guide studs. Bolts are tightened to the specified torque and the flywheel is inspected for proper runout.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...8ufjsekddm8u
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...8ufjsekddm8u
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i05165105
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6895
or
4C-6366 (1)
Valve Guide Driver 1
( 1 )
If necessary, use Tooling on inlet valve guides.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01137612
1. Use Tooling (A) to remove the inlet valve guides and exhaust valve guides from the
cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-6895
or
4C-6366 (1)
Valve Guide Driver 1
B 173-5524 Guide Collar 1
C 342-6109 Guide Collar 1
( 1 )
If necessary, use Tooling on inlet valve guides.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g03317961
1. Position the inlet valve guide and exhaust valve guide in the cylinder head. Tap on the top
of the valve guides in order to start the inlet valve guides and exhaust valve guides into the
cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install the Exhaust valve guide. Use Tooling (A) and
Tooling (C) to install the Intake valve guide. Install the valve guides until the protrusion is
Distance (X) . Distance (X) is 12.0 ± 0.5 mm (0.47 ± 0.02 inch) above the cylinder head
assembly.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:28:37 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i04420274
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-3095 Puller Handle 1
B
6V-4194 (1)
Valve Seat Extractor 1
1U-9167 (2)
Valve Seat Extractor 1
( 1 )
For use with Exhaust Valve Seat
( 2 )
For use with Intake Valve Seat
Start By:
A. Remove inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
1/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 1 g01137634
1. Use Tooling (A) and Tooling (B) to remove valve seat inserts (1) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
C
4C-6372 (1)
Valve Seat Driver 1
364-4009 (2)
Valve Seat Driver 1
( 1 )
For use with Exhaust Valve Seat
( 2 )
For use with Intake Valve Seat
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 2 g01137637
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
1. Lower the temperature of new valve seat inserts (1) . Use Tooling (C) to install valve seat
inserts (1) into the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:29:32 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02297805
Engine Oil Filter Base and Oil Cooler - Remove
SMCS - 1306-011; 1378-012
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
1/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01150737
1. Use Tooling (A) to remove engine oil filter (1).
2/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 2 g01150959
2. Disconnect hose assembly (2). Remove bolts (3). Remove engine oil filter base (4) and the
oil seal.
3/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 3 g01150963
3. Remove engine oil cooler (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:30:28 UTC+0800 2020
4/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02298275
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base and Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g01151723
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove elbow (1) and O-ring seal (3) from engine oil filter base (6).
2. Remove plug (2) and the O-ring seal from engine oil filter base (6).
3. Remove spring (4) and valve (5) from engine oil filter base (6).
4. Remove plug (9) and the O-ring seal from engine oil filter base (6).
5. Remove spring (8) and valve (7) from engine oil filter base (6).
Wed Jun 3 17:31:24 UTC+0800 2020
2/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
3/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02300235
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 1 g01151723
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Apply clean engine oil to O-ring seal (3). Install O-ring seal (3) on elbow (3). Install elbow
(1) in engine oil filter base (6).
2. Apply clean engine oil to the O-ring seal. Install the O-ring seal on plug (2).
3. Apply clean engine oil to valve (5). Install valve (5), spring (4), and plug (2) in engine oil
filter base (6).
4. Apply clean engine oil to the O-ring seal. Install the O-ring seal on plug (9).
5. Apply clean engine oil to valve (7). Install valve (7), spring (8), and plug (9) in engine oil
filter base (6).
2/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base and Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:32:20 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02298181
Engine Oil Filter Base and Oil Cooler - Install
SMCS - 1306-012; 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 2 g01150959
2. Apply clean engine oil to the oil seal. Install the oil seal in engine oil filter base (4). Position
engine oil filter base (4) over the engine oil cooler. Install bolts (3). Connect tube assembly
(2).
3/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 3 g01150737
3. Install engine oil filter (1).
4. Fill the engine with oil to the correct level. Refer to Operation and Maintenance Manual,
"Refill Capacities and Recommendations".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:33:16 UTC+0800 2020
4/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02298281
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01151740
1. Remove bolts (1).
2. Remove bolt (2).
3. Remove bolts (3) and remove engine oil pump (4).
4. Remove the O-ring seal that is located between the cylinder block and the outlet elbow.
2/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 2 g01152424
5. Remove bolts (5) and remove outlet elbow (6).
6. Remove bolts (7). Remove oil pickup tube (8) and the gasket.
Illustration 3 g01152433
3/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. 7. Remove bolt (12) and the washer. Remove idler gear (11). Use Tooling (A) in order to
remove bearing (10) from idler gear (11). Remove shaft (9) from engine oil pump (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 3 17:34:11 UTC+0800 2020
4/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR WBC
Configuration: 336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i07521711
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Illustration 1 g01152433
1. Install shaft (9) onto engine oil pump (4). Use Tooling (A) and a suitable press in order to
install bearing (10) into idler gear (11). Position idler gear (11) on shaft (9). Install bolt (12)
and the washer.
Illustration 2 g06348586
2. Mount the engine oil pump (4) to the cylinder block by hand tightening the mounting bolts
(3) into the cylinder block.
Note: Ensure that the mounting surfaces for the engine oil pump are thoroughly clean.
3. Without the O-rings, assemble the outlet elbow (6) between the block and the oil pump,
using the washers and bolts (2) and (5). Hand tighten only.
2/4
336D2 & 336D2 L Excavators WBC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...