This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves 28 steps to remove components like the head, brake piston, rotating assembly, bearings and seals. The assembly process reverses the disassembly with 27 steps, applying lubricant and torque specifications where needed. Tools required include adapters, nuts, threaded rods, eyebolts and bearing pullers.
Caterpillar cat 324 e l excavator (prefix tlf) service repair manual (tlf0000...fjsekkdmme
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that remove components like the head, seals, springs, brake piston, plates, and bearings. It then lists 11 steps for assembly that install components like seals, cover, piston actuator, and bearings in the reverse order of disassembly. Tools required include bolts, nuts, eyebolts, retaining ring pliers, drivers, pullers, and loctite.
Caterpillar cat 324 e ln excavator (prefix tlf) service repair manual (tlf000...fjsekkdmme
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that remove components like the head, seals, springs, brake piston, plates, and bearings. It then lists 11 steps for assembly that install components like seals, cover, piston actuator, and bearing in the reverse order of disassembly. Tools required include bolts, nuts, eyebolts, retaining ring pliers, bearing puller, and adapter.
Caterpillar Cat 329E L Excavator (Prefix RLD) Service Repair Manual (RLD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...udjdkkmdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar Cat 329E L Excavator (Prefix RLD) Service Repair Manual (RLD00001...paws21610697
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 329 e ln excavator (prefix rld) service repair manual (rld000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 324 e l excavator (prefix tlf) service repair manual (tlf0000...fjsekkdmme
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that remove components like the head, seals, springs, brake piston, plates, and bearings. It then lists 11 steps for assembly that install components like seals, cover, piston actuator, and bearings in the reverse order of disassembly. Tools required include bolts, nuts, eyebolts, retaining ring pliers, drivers, pullers, and loctite.
Caterpillar cat 324 e ln excavator (prefix tlf) service repair manual (tlf000...fjsekkdmme
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that remove components like the head, seals, springs, brake piston, plates, and bearings. It then lists 11 steps for assembly that install components like seals, cover, piston actuator, and bearing in the reverse order of disassembly. Tools required include bolts, nuts, eyebolts, retaining ring pliers, bearing puller, and adapter.
Caterpillar Cat 329E L Excavator (Prefix RLD) Service Repair Manual (RLD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...udjdkkmdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar Cat 329E L Excavator (Prefix RLD) Service Repair Manual (RLD00001...paws21610697
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 329 e ln excavator (prefix rld) service repair manual (rld000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...8ufjsekddm8u
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...8ufjsekddm8u
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, bolts securing the housing, and oil seal from the housing. It then describes how to install a new oil seal, gasket, and reattach the housing using bolts, and reinstall the flywheel and electric starting motor.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...8ufjsekddm8u
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and torque wrench to reinstall these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
Caterpillar Cat 323D L Excavator (Prefix NZF) Service Repair Manual (NZF00001...8ufjsekddm8u
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using specialized tools to compress the valve springs and position the pistons at top dead center. Springs are removed in pairs from specific cylinders and must be replaced in the same order. Installation requires lubricating seals, compressing springs with a tool to insert retainers and keepers, and checking valve clearance after installation is complete. Safety precautions are outlined to prevent injury from released spring forces.
Caterpillar Cat 323D L Excavator (Prefix BYM) Service Repair Manual (BYM00001...8ufjsekddm8u
1) The document provides instructions for removing and installing various engine components on a Caterpillar 323D L Excavator, including valve seat inserts, the engine oil cooler, and the engine oil relief valve.
2) The procedures include a list of required tools and step-by-step instructions describing how to remove, disassemble, and assemble each component while taking appropriate safety precautions.
3) Technicians are advised to keep all parts clean and free of contaminants to prevent damage and wear.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...8ufjsekddm8u
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like the spring, arms, bracket and washer onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, the pushrods and rocker shaft are positioned and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual (JLG00001...8ufjsekddm8u
This service repair manual provides instructions for removing and installing valve seat inserts, removing and disassembling the engine oil cooler, and assembling the engine oil cooler for a Caterpillar C6.4 engine powering a 323D L excavator. The document lists required tools and safety notices, and includes illustrations of the removal, disassembly, and assembly procedures.
Caterpillar Cat 323D L Excavator (Prefix LFL) Service Repair Manual (LFL00001...8ufjsekddm8u
1) The document provides instructions for removing and installing the fuel injection pump on a Caterpillar C6.4 engine.
2) To remove the pump, various hoses, tubes, brackets and electrical connections must be disconnected and markings made for installation. Bolts then need to be removed to access the pump.
3) Installation involves reversing the removal process, ensuring cleanliness, replacing washers, and torquing all connections to the specified values.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...8ufjsekddm8u
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are required to lift the housing and remove the oil seal. When installing, a new gasket and oil seal are used and the housing is bolted back in place before reinstalling the flywheel and starting motor.
This document provides installation instructions for a rear power take-off (RPTO) on a 323 excavator with a C7.1 engine. It describes 20 steps to install the RPTO, including installing sleeve bearings, gears, idler hubs, adapters and bolts. Precautions are given to keep components clean and ensure proper alignment of parts. Tools required include drivers and sockets.
This document provides instructions for disassembling and assembling the travel motor of a 323D and 323D L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, and shaft assembly. It then describes 13 steps to reassemble the travel motor by installing components like the shaft assembly, cam plate, barrel assembly, and head in the reverse order of disassembly. Precautions are given to clean parts thoroughly, mark components for reinstallation, and ensure proper alignment of parts.
1) The document provides instructions for removing and installing a flywheel from a C7.1 engine that powers a 323 excavator.
2) To remove the flywheel, bolts must first be removed and guide studs installed to support the flywheel. Lifting equipment is then used to lift the flywheel off while inspecting components for wear or damage.
3) Flywheel installation requires cleaning and lifting the flywheel into place using guide studs. Bolts are tightened to the specified torque and the flywheel is inspected for proper runout.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...8ufjsekddm8u
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...8ufjsekddm8u
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...8ufjsekddm8u
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix YSD) Service Repair Manual (YSD00001...8ufjsekddm8u
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, bolts securing the housing, and oil seal from the housing. It then describes how to install a new oil seal, gasket, and reattach the housing using bolts, and reinstall the flywheel and electric starting motor.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...8ufjsekddm8u
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and torque wrench to reinstall these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
Caterpillar Cat 323D L Excavator (Prefix NZF) Service Repair Manual (NZF00001...8ufjsekddm8u
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using specialized tools to compress the valve springs and position the pistons at top dead center. Springs are removed in pairs from specific cylinders and must be replaced in the same order. Installation requires lubricating seals, compressing springs with a tool to insert retainers and keepers, and checking valve clearance after installation is complete. Safety precautions are outlined to prevent injury from released spring forces.
Caterpillar Cat 323D L Excavator (Prefix BYM) Service Repair Manual (BYM00001...8ufjsekddm8u
1) The document provides instructions for removing and installing various engine components on a Caterpillar 323D L Excavator, including valve seat inserts, the engine oil cooler, and the engine oil relief valve.
2) The procedures include a list of required tools and step-by-step instructions describing how to remove, disassemble, and assemble each component while taking appropriate safety precautions.
3) Technicians are advised to keep all parts clean and free of contaminants to prevent damage and wear.
Caterpillar Cat 323D L Excavator (Prefix NDE) Service Repair Manual (NDE00001...8ufjsekddm8u
The document provides instructions for installing the rocker shaft and pushrods on a C6.4 engine. The procedure involves installing various components like the spring, arms, bracket and washer onto the shaft assembly. Retaining rings are then installed to secure the assembly. Finally, the pushrods and rocker shaft are positioned and tightened to specified torques to complete the installation.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual (JLG00001...8ufjsekddm8u
This service repair manual provides instructions for removing and installing valve seat inserts, removing and disassembling the engine oil cooler, and assembling the engine oil cooler for a Caterpillar C6.4 engine powering a 323D L excavator. The document lists required tools and safety notices, and includes illustrations of the removal, disassembly, and assembly procedures.
Caterpillar Cat 323D L Excavator (Prefix LFL) Service Repair Manual (LFL00001...8ufjsekddm8u
1) The document provides instructions for removing and installing the fuel injection pump on a Caterpillar C6.4 engine.
2) To remove the pump, various hoses, tubes, brackets and electrical connections must be disconnected and markings made for installation. Bolts then need to be removed to access the pump.
3) Installation involves reversing the removal process, ensuring cleanliness, replacing washers, and torquing all connections to the specified values.
Caterpillar Cat 323D L Excavator (Prefix L5Z) Service Repair Manual (L5Z00001...8ufjsekddm8u
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C6.4 engine. It describes removing the electric starting motor, flywheel and ring gear before removing the flywheel housing bolts. Tools are required to lift the housing and remove the oil seal. When installing, a new gasket and oil seal are used and the housing is bolted back in place before reinstalling the flywheel and starting motor.
This document provides installation instructions for a rear power take-off (RPTO) on a 323 excavator with a C7.1 engine. It describes 20 steps to install the RPTO, including installing sleeve bearings, gears, idler hubs, adapters and bolts. Precautions are given to keep components clean and ensure proper alignment of parts. Tools required include drivers and sockets.
This document provides instructions for disassembling and assembling the travel motor of a 323D and 323D L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, and shaft assembly. It then describes 13 steps to reassemble the travel motor by installing components like the shaft assembly, cam plate, barrel assembly, and head in the reverse order of disassembly. Precautions are given to clean parts thoroughly, mark components for reinstallation, and ensure proper alignment of parts.
1) The document provides instructions for removing and installing a flywheel from a C7.1 engine that powers a 323 excavator.
2) To remove the flywheel, bolts must first be removed and guide studs installed to support the flywheel. Lifting equipment is then used to lift the flywheel off while inspecting components for wear or damage.
3) Flywheel installation requires cleaning and lifting the flywheel into place using guide studs. Bolts are tightened to the specified torque and the flywheel is inspected for proper runout.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 15 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 16 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...8ufjsekddm8u
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
This document provides instructions for removing the front housing on a C4.4 engine. The steps include:
1. Removing other components like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting wiring, cutting cable straps and removing bolts to separate the bypass tube from the housing and cylinder head.
3. Removing bolts of different lengths to detach the front housing from the cylinder block, and removing the gasket and thrust washer.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...8ufjsekddm8u
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines 16 steps to disassemble parts like the traction control valve, bearing, relief valve assemblies, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324E L EXCAVATOR TLF
Configuration: 324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit Machine
Systems
Media Number -KENR9844-04 Publication Date -01/04/2015 Date Updated -14/04/2015
i04216221
Travel Motor - Disassemble
SMCS - 4351-015
S/N - JCZ1-UP
S/N - K2L1-UP
S/N - KTE1-UP
S/N - LDG1-UP
S/N - PNW1-UP
S/N - PTY1-UP
S/N - RDX1-UP
S/N - RLD1-UP
S/N - TLF1-UP
S/N - TST1-UP
S/N - WJK1-UP
S/N - ZCD1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
1/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
2/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3), port plate (4), and bearing (5) .
3/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g00887311
7. Remove O-ring seals (6). Remove springs (7) .
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
4/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 8. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
5/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 8 g00887401
Illustration 9 g00887405
12. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
6/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 14. Remove shaft (15) from rotating assembly (16) .
Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
7/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 13 g00887463
17. Rotate shaft (15). Install shaft (15) into a suitable press. Install Tooling (E). Remove bearing
race (19) from shaft (15) .
Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
9/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
10/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 ...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 28 23:32:26 UTC+0800 2020
11/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 ...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324E L EXCAVATOR TLF
Configuration: 324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit Machine
Systems
Media Number -KENR9844-04 Publication Date -01/04/2015 Date Updated -14/04/2015
i04216229
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
2/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) in order to install
lip seal (28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) in order to install retaining ring (27) .
3/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g02107975
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
4/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21) .
5/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
6/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g02107957
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
7/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
8/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
9/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5) .
Illustration 22 g00887295
10/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 ...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 177 ± 18 N·m (130.5 ± 13.27 lb ft).
End By: Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 28 23:33:25 UTC+0800 2020
11/11
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 ...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324E L EXCAVATOR TLF
Configuration: 324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit Machine
Systems
Media Number -KENR9844-04 Publication Date -01/04/2015 Date Updated -14/04/2015
i04216189
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/4
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00878123
2. Install new O-ring seal (6). Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4), as shown.
4. The weight of the travel motor is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/4
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 5. Carefully install travel motor (4) onto Tooling (A). Slide the travel motor into the final
drive.
6. Install one of three bolts (5) that secures the travel motor to the final drive.
7. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
8. Install remaining bolts (2) .
9. Connect hose assembly (3). Connect hose assembly (1) .
10. Fill the final drive with oil.
ReferenceRefer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
ReferenceRefer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for
the correct filling procedure.
11. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
12. Obtain a hydraulic oil sample from the main S·O·S port.
ReferenceRefer to Operation and Maintenance Manual, "Sampling Interval and Location of
Sampling Valve" for the correct location.
13. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
ReferenceRefer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
3/4
324E L & 324E LN Excavators TLF00001-UP (MACHINE) POWERED BY C7.1 En...
2020/7/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...