2000 Intrepid - Replacement of Interior Front Door Handle

1,480 views
1,283 views

Published on

This 2000 Intrepid report provides information to permit replacement of interior front door handle or bezel instead of replacing the door trim panel.

Published in: Automotive
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
1,480
On SlideShare
0
From Embeds
0
Number of Embeds
3
Actions
Shares
0
Downloads
2
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

2000 Intrepid - Replacement of Interior Front Door Handle

  1. 1. 2000 Intrepid Replacement of Interior Front Door HandleNUMBER: 23-013-04NOTE: This report replaces the technical service bulletin no. 23-047-02, DATEDSUBJECT:Interior Front Door Handle/Bezel ReplacementOVERVIEW:This report provides information to permit replacement of interior front door handle orbezel instead of replacing the door trim panel.MODELS:2000 IntrepidFAILURE CODE:P8 New PartPROBLEM:An interior front door handle/bezel needs to be replaced.**PARTS REQUIRED:Mopar PartsAR 05102832AA Handle/Bezel, Left, Intrepid, Agate, Trim Codes AZ or D5AR 05102833AA Handle/Bezel, Right, Intrepid, Agate, Trim Codes AZ or D5AR 05102834AA Handle/Bezel, Right, Intrepid, Dk Camel, Trim Code K9
  2. 2. AR 05102835AA Handle/Bezel, Left, Intrepid, Dk Camel, Trim Code K9AR 05102836AA Handle/Bezel, Right, Intrepid, Dk Slate, Trim Code DVAR 05102837AA Handle/Bezel, Right, Intrepid, Dk Sandstone, Trim Code T5AR 05102838AA Handle/Bezel, Right, Intrepid, Dk Taupe, Trim Code L5AR 05102839AA Handle/Bezel, Left, Intrepid, Dk Slate, Trim Code DVAR 05102840AA Handle/Bezel, Left, Intrepid, Dk Sandstone, Trim Code T5AR 05102841AA Handle/Bezel, Left, Intrepid, Dk Taupe, Trim Code L5NOTE:Each kit contains one handle/bezel assembly, six pushnuts and an instruction sheet.EQUIPMENT REQUIRED:NPN 21/64 in. (8.3mm) Drill BitREPAIR PROCEDURE:Step 1: with the guidance of section 23 of service manual or the method outlined onTechCONNECT, proceed by removing the front door trim panel.Step 2: place the trim door panel on clean work area. Drill out the mounting boss heatstakes that connects the existing door handle to the trim panel. Remember to take extracaution to drill exactly in the center of each heat stake.Step 3: after drilling, remove the existing handle/bezel from trim panel.Step 4: get rid of the plastic fillings at the back of the trim panel.Step 5: set the new handle into its position.Step 6: fasten the nuts into the handle/bezel bosses.
  3. 3. Step 7: push the nuts all the way down by using a 10mm socket on the mountingbosses. This is to secure firmly the handle/bezel into the door trim panel. Check it bywiggling left and right the handle to ensure if it snug-fit.Step 8: install the lock switch you got from the original handle/bezel into the new one.Step 9: re-install the door trim panel following the same procedures outlined onTechCONNECT or those that can be found on section 23 of the service manual.POLICY:Covered with refund within the provision of the warranty.TIME ALLOWANCE:23-42-45-92/93 Replace Front Door Handle, Right or Left 0.4 Hrs.

×