0
HOW TO REPLACE YOUR BRACKETT AIR FILTER ELEMENT STEP 1 <ul><li>When performing any inspection or maintenance on the powerp...
STEP 2 <ul><li>When you have finished viewing this presentation, use the “CAPS” program found on the home page of  www.ape...
STEP 3 <ul><li>Remove the necessary cowling or access panel, if necessary, to gain access to the induction air filter. </l...
STEP 4 <ul><li>Remove screws attaching filter grill assembly to filter frame and remove foam filter element. </li></ul>
STEP 5 <ul><li>CAUTION :  Be sure drain hole is clean. </li></ul><ul><li>Note:   Filter frame assembly does not need to be...
STEP 6 <ul><li>Clean filter frame of any dirt or debris.  </li></ul><ul><li>Install correct element using the same hardwar...
STEP 7 <ul><li>Remove any tools or supplies from the engine compartment. </li></ul><ul><li>Reinstall any cowling or access...
BRACKETT AIR FILTER ELEMENT INSTALLATION COMPLETE <ul><li>Make appropriate logbook entry of the work performed.  The FAA h...
Upcoming SlideShare
Loading in...5
×

How to install bracket airfilter

1,478

Published on

Published in: Self Improvement
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
1,478
On Slideshare
0
From Embeds
0
Number of Embeds
0
Actions
Shares
0
Downloads
4
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Transcript of "How to install bracket airfilter"

  1. 1. HOW TO REPLACE YOUR BRACKETT AIR FILTER ELEMENT STEP 1 <ul><li>When performing any inspection or maintenance on the powerplant, propeller or that requires turning on the master switch, or pulling the propeller through by hand; treat the propeller as if the ignition switch were on. DO NOT stand, nor allow anyone else to stand, within the arc of the propeller as a loose or broken wire or component malfunction could cause the propeller to rotate. </li></ul>
  2. 2. STEP 2 <ul><li>When you have finished viewing this presentation, use the “CAPS” program found on the home page of www.apex- inc .biz . Select the proper air filter/element for your aircraft. </li></ul>
  3. 3. STEP 3 <ul><li>Remove the necessary cowling or access panel, if necessary, to gain access to the induction air filter. </li></ul>
  4. 4. STEP 4 <ul><li>Remove screws attaching filter grill assembly to filter frame and remove foam filter element. </li></ul>
  5. 5. STEP 5 <ul><li>CAUTION : Be sure drain hole is clean. </li></ul><ul><li>Note: Filter frame assembly does not need to be removed unless damage is found upon inspection. </li></ul><ul><li>Inspect filter frame assembly for any loose gasket material, loose hardware that attached the frame to the airbox or broken screen material. Correct any problems found before installing the new element. </li></ul>
  6. 6. STEP 6 <ul><li>Clean filter frame of any dirt or debris. </li></ul><ul><li>Install correct element using the same hardware that was removed. </li></ul>
  7. 7. STEP 7 <ul><li>Remove any tools or supplies from the engine compartment. </li></ul><ul><li>Reinstall any cowling or access panels that were removed. </li></ul>
  8. 8. BRACKETT AIR FILTER ELEMENT INSTALLATION COMPLETE <ul><li>Make appropriate logbook entry of the work performed. The FAA has a sample logbook entry shown in the free video on our home page at www.apex- inc .biz . </li></ul><ul><li>This presentation contains information that is consistent with FAR 65.83 “Recent Experience Requirements.” </li></ul><ul><li>Please visit www.apex- inc .biz to view a free video that reviews Basic Maintenance for Pilots and Technicians as part of FAR 43 and 91. Click on “Watch the video” located about half way down on the left side of the page. </li></ul>
  1. A particular slide catching your eye?

    Clipping is a handy way to collect important slides you want to go back to later.

×