Presentation Agenda CCTV vs. IP Surveillance Resolution Cabling Cost...etc IP Surveillance Installation Topology Choice of Camera Type Migration from CCTV Choice of Lens Ports and DIDO Bandwidth and Storage Recording Device Choice of Recording Software Wireless and IPCAM Integration
Use UPS to protect IPCam Network from Power Outage and Power Surge Use PoE Switch to supply power and data to Cameras Use NVR for Video Recording Put NVR on UPS To ensure Uninterrupted Recording
Power over Ethernet Power over Ethernet switch provide both Data and Electricity to the IP Cameras. So only single cable is needed. In addition, the 802.3af PoE standard uses 48V electricity which can provide up to 100 meter of cabling distance.
AirLive IPCAMs use mostly 802.3af PoE spec. The Pan-Title Camera and Outdoor cameras uses about 10 watt each, while the other cameras uses 4 to 5 watt each. Therefore, the AirLive PoE switch supplies enough power per channel.
Indoor Dome Type Indoor Dome Type Can be Mounted on the Ceiling Viewing Angle Adjustable Can be installed with Vari-Focal Lens POE Installation For Elevator, Shopping Mall, Hotel
Indoor Dome Application Environment Hotel Hallway Elevator Shopping Mall
Outdoor Bullet Type Outdoor Bullet Type All-in-One Multi-Purpose IPCAM IP-66 Weather Proof Suitable for Both Outdoor and Indoor Use Infrared IR LED Compact Comparing to Legacy Outdoor Type Stairway, Parking Lot, Streets, Outside Areas
Outdoor Bullet Type Application Environment Indoor Parking Outdoor Parking Stairway Street Patrol
Vandal Dome Vandal Dome Steel and Temper Glass Construction Difficult to Break IP-66 Outdoor Water Proof POE Installation Banks, Supermarket, Streets, Factory
Vandal Application Environment Factory Bank Super Market Shopping Mall
Vandal Pan-Tilt Vandal Pan and Tilt Rotation in both Horizontal or Vertical Axis Able to Patrol the Area IP-66 Water Proof Steel and Temper Glass Construction Parking Lot, Main Entrance, Bank, Factory
The NVR is a NAS device with recording software inside. It will record and send notification to admiinstrator without PC. You can view image through web browser NVR Recording your IP Camera without PC
Simply type an address into the NVR Google eMap function, then insert your camera into the map. You can know the location of your camera immediately. NVR Google EMAP Function
Portuguese and Spanish are supported! NVR Multi-Language Support
Just open the browser on your Smartphone and iPAD. Then enter your NVR’s IP address. You can view your cameras on the mobile devices easily. NVR Support Smart Phone and iPAD
NVR NVR can handle up to 16 camera recording at the time. However, the resolution, image quality, and motion movements can influence the frame rate. The lowest FPS shows all cameras in best quality and constant object movements. We recommend using Quality 6 recording which can keep the system at best balance.
PC Recording Software AirLive Campro Express and Campro HD
Planning a wireless IPCAM Network Find Out the Bandwidth Requirement Wireless Distance vs. Bandwidth How to Connect the IPCAM with CPE Wireless Topology Using the Right Equipment
The wireless bandwidth depends on the distance and wireless standard. In general, the 5GHz frequency spectrum has less interference which provides more stable bandwidth for mission critical applications such as IP Surveillance. The following table shows wireless bandwidth tested at foggy conditions. Snow and heavy rain can reduce the bandwidth by half. In general, the 11a/Super-A/Super-A with Static Turbo holds the bandwidth better over longer distance and in bad weather conditions. The advantage for 11n disappears after 1km and in bad weather.
You can find the Bandwidth Requirement using the calculator program from AirLive. By calculating bandwidth vs. wireless throughput. You can decide find out how many cameras you can support on each CPE. It is advised to leave 50% bandwidth for interference and rain factory. For example, if you use Super-A mode at 1km distance. You can safely support about 7 MegaPixel IP Cameras.
A large wireless network deployment typically consist of AP network and Bridge network. AP network is between Base Station and CPE. Bridge network is for connections between Base Stations. Using this method, you can have much better control over bandwidth. So as the network gets larger, it won’t slow down.
We can create a network of redundancy for Bridge network by using the multi-point WDS with STP spanning tree. So when one link failed, the network can go through another path to reach destinations..
The AP+Bridge hybrid network offer the most efficient topology for the wide area outdoor deployment of IPCAM network