service repair manual

1. Service Information
Document Title: Function Group: Information Type: Date:
Hydraulic oil tank, oil,
replace if system is filled
with mineral oil or Volvo
Biodegradable hydraulic oil
46. If system is filled with
other biologically
degradable hydraulic oil,
replace every 2000 hour.
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Hydraulic oil tank, oil, replace if system is filled with mineral oil or
Volvo Biodegradable hydraulic oil 46. If system is filled with other
biologically degradable hydraulic oil, replace every 2000 hour.
This is part of other procedure.
Op nbr
14360000 Vacuum pump / 24V
WARNING
Work carefully when changing oil as hot oil can cause severe burns to unprotected skin.
CAUTION
Maintain greatest possible cleanliness during all work on the hydraulic system.
CAUTION
Take care of filters, oils and liquids in an environmentally safe way.
NOTE!
The machine shall be in lowered position and the engine shall have run at idle, so that the accumulators are drained of oil
and pressure. See .
191 Service positions
1. Draining
Figure 1

2. 1. Drain connections, hydraulic oil tank
Remove the protective covers from the drain connections on the hydraulic oil tank's underside and at the rear end
by the wheel.
2. Connect the drain hose to the drain connections.
3. Drain the oil into an oil barrel that holds approx. 262 litres (69.2 US gal).
4. After draining, remove the drain hose and reinstall the protective covers on the drain connections.
5. Filling.
Figure 2
1.
2.
3.
Filling
Vacuum pump connection to breather filter hose
Vacuum pump
Remove the breather filter for the hydraulic oil tank.
NOTE!
To increase the fill rate, connect a vacuum pump.
6. Connect the vacuum pump to the breather filter hose, and plug in the cable in the 24 V socket in the right
instrument panel in the cab.
7. Clean around the plug for the filler hole.
NOTE!
Always fill oil through the filler hole so that the oil is filtered.
8. Remove the plug for the filler hole in the cover.
9. Start the vacuum pump and fill oil, see through the filler hole via the hydraulic oil's
160 Lubricants, specifications
return oil filter, volume see . Fill oil until the level glass shows max. level.
900 Hydraulic system, capacities
10. Reinstall the plug for the filler hole, to prevent oil from spraying out when the machine is started.

3. 11. Turn off the vacuum pump and remove it from the breather filter hose. Unplug the cable from the instrument panel
in the cab.
12. Reinstall the breather filter.
NOTE!
The engine may not be started when the vacuum pump is connected.
13. Start the machine and let it idle for approx. 5 minutes until the fans run at steady rpm.
14.
Figure 3
1. Switch, FS-system
Activate the hydraulic suspension with the switch.
15. Turn off the engine when the machine is in normal position.
16. Top up so that the oil reaches up to 3/4 in the level glass.

4. Service Information
Document Title: Function Group: Information Type: Date:
Hydraulic oil tank, return
oil filter, replace, and
magnetic rods, clean
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Hydraulic oil tank, return oil filter, replace, and magnetic rods, clean
Op nbr
This is part of other procedure.
CAUTION
Maintain greatest possible cleanliness during all work on the hydraulic system.
CAUTION
Take care of filters, oils and liquids in an environmentally safe way.
1. Clean around the cover for the hydraulic oil's return oil filter.
2. Spin off the cover.
Figure 1
1. Return oil filter
3.

5. Figure 2
1. Filter insert for return oil filter
Remove the filter inserts.
4.
Figure 3
1.
2.
3.
4.
Magnetic rod
Filter
Filter bracket
Fastener nut
Dismantle the filter insert as shown in the figure.
5.
Figure 4
Magnetic rod
Wipe clean the magnetic rod thoroughly and install a new filter in the filter holder.
6. Check O–ring on the magnetic rod.
7. Reinstall the filter insert.
8. Repeat step 5–8 for the other filter insert.
9. Check O-ring for the cover and reinstall it.

6. Service Information
Document Title: Function Group: Information Type: Date:
Hydraulic oil tank, breather
filter, replacing
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Hydraulic oil tank, breather filter, replacing
Op nbr
This is part of other procedure.
NOTE!
The filter is of the disposable type, do not clean it, replace the filter.
CAUTION
Take care of filters, oils and liquids in an environmentally safe way.
1.
Figure 1
1. Breather filter for hydraulic oil tank
Change breather filter for the hydraulic oil tank.

7. Service Information
Document Title: Function Group: Information Type: Date:
Brake cooling oil tank,
breather filter, replacing
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Brake cooling oil tank, breather filter, replacing
Op nbr
This is part of other procedure.
1.
Figure 1
1. Breather filter, brake cooling oil tank
Change breather filter for the brake cooling oil tank.

8. Service Information
Document Title: Function Group: Information Type: Date:
Fuel tank, axles, gearbox
and dropbox, breather
filter, replacing
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Fuel tank, axles, gearbox and dropbox, breather filter, replacing
Op nbr
This is part of other procedure.
CAUTION
Take care of filters, oils and liquids in an environmentally safe way.
1.
Figure 1
1. Breather filter, fuel tank
Change breather filter for the fuel tank.

9. 2.
Figure 2
1. Breather filter, front axle and dropbox
Change breather filter for the dropbox and the tractor's front axle.
3.
Figure 3
1. Breather filter, front bogie axle
Change breather filter for the front bogie axle.

10. 4.
Figure 4
1. Breather filter, rear bogie axle
Change breather filter for the rear bogie axle.
5.
Figure 5
1. Breather filter for transmission
Change breather filter for the transmission.

11. Service Information
Document Title: Function Group: Information Type: Date:
Service brake, brake disc
wear, check
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Service brake, brake disc wear, check
Op nbr
This is part of other procedure.
NOTE!
This applies for normal operating conditions, in tougher conditions the brake discs should be checked more often.
1. Apply the parking brake.
2. Start the engine and run up pressure in the system.
3. Apply the load and dump brake.
Figure 1
1. Protective cap
4. Remove the wear indicator cap.
Figure 2

12. 1. Wear indicator
5.
Figure 3
Insertion of indicator
Carefully push in the wear indicator as far as possible, e.g., with a small screwdriver. Then measure the wear
indicator's insertion inside of the nipple's face as shown. Note the measurement.
6.
Figure 4
Cut-away view, wear indicator
X is the insertion measurement
The discs are worn out when measurement X equals 0 mm.
Shaft Value (mm) for new discs
Front axle X=6.8 ± 0.1
A35F / A35F FS
Front bogie axle X=3.4 ± 0.1
Rear bogie axle X=3.4 ± 0.1
Front axle X=6.8 ± 0.1
A40F / A40F FS
Front bogie axle X=4.5 ± 0.1
Rear bogie axle X=4.5 ± 0.1
7. Reinstall the wear indicator cap.
8. Repeat the measurement for the rest of the brakes.
9. Turn off the engine.

13. Service Information
Document Title: Function Group: Information Type: Date:
Parking brake pads, check 173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Parking brake pads, check
Op nbr
This is part of other procedure.
1.
Figure 1
Check the pads' thickness as shown in figure.
NOTE!
Min. measurement for parking brake pads is 5 mm (0.2 in).

14. Service Information
Document Title: Function Group: Information Type: Date:
Steering cylinder bearings,
clearance, check
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Steering cylinder bearings, clearance, check
Op nbr
This is part of other procedure.
NOTE!
Checking is done by 2 persons.
1.
Figure 1
1.
2.
Cylinder rod
Hitch
Park the machine on level ground and apply the parking brake.
2. Secure the dial indicator with magnetic base on the hitch as shown in figure.
3. Start the machine and turn the steering wheel back and forth with small movements. Measure the movement of the
piston rod bearing.
NOTE!
No clearance allowed.

15. 4.
Figure 2
1.
2.
Cylinder end
Frame
Secure the dial indicator on the tractor's frame, and measure the movement of the cylinder barrel's bearing in a
similar way as for the piston rod bearing.
NOTE!
No clearance allowed.
5. Perform the same measurements on the other steering cylinder.

16. Service Information
Document Title: Function Group: Information Type: Date:
Load body, rubber
cushions, clearance, check
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Load body, rubber cushions, clearance, check
Op nbr
This is part of other procedure.
WARNING
Never enter under an unsupported load body.
1. Clean around and under the rubber pads.
2. Check that the front rubber pads have equal clearance to the frame, 10±2 mm (0.39±0.08 in).
Figure 1
1. Front rubber pad
Figure 2
1. Rear rubber pad
3. Check that the rear rubber cushions, located over the bogie, have contact with the load body and are compressed
equally on both sides.

17. 4. If needed, adjust with shims under the rear rubber pads.

18. Service Information
Document Title: Function Group: Information Type: Date:
Steering joint bearings,
first check of steering joint
bearings after 6000 hours.
Thereafter every 2000
hours.
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Steering joint bearings, first check of steering joint bearings after
6000 hours. Thereafter every 2000 hours.
Op nbr
This is part of other procedure.
Checking clearance is carried out by 2 persons.
NOTE!
Make sure that the steering joint lock is mounted.
1.
Figure 1
1.
2.
Front frame
Hitch
Place a magnetic base with the dial indicator as shown in figure.
The magnetic base is located against the hitch and the needle against the front frame.
NOTE!
To obtain a correct value, the dial indicator must be positioned on the middle of the hitch.
2. Start the engine and let it idle.
NOTE!
Check that no persons are in front of or behind the machine.
3. Apply the brake pedal and release the parking brake.
4. Move the gear selector to position "D".
5. Apply the parking brake.

19. 6. Carefully release the brake pedal.
7. Reset the dial gauge.
8. Repeat from "Start the engine and let it idle", but move the gear selector to position "R" instead of position "D".
9. Read off the clearance on the dial indicator.
NOTE!
No clearance allowed!
10.
Figure 2
1.
2.
Hitch
Front frame
Move the magnetic base with dial indicator to the lower steering joint bearing as shown in figure.
The magnetic base is located on the hitch and the needle against the front frame.
11. Repeat the method according to the above with the gear selector in both "D" and "R".
NOTE!
No clearance allowed!

20. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

21. Service Information
Document Title: Function Group: Information Type: Date:
Frame joint bearings,
clearance, check
173 Service Information 2014/8/6 0
Profile:
ART, A35F FS (37141) [GB]
Frame joint bearings, clearance, check
This is part of other procedure.
Op nbr
11668008 Standard Jack Double
11668007 Standard Jack Single
1.
Figure 1
1.
2.
Trailer frame
Hitch
Place the dial indicator as shown.
The magnetic base is located on the trailer frame and the needle against the hitch.