This document provides instructions for disassembling and assembling the travel motor on Caterpillar 345B and 345B L Excavator models. It lists required tools and parts and provides 32 numbered steps to fully disassemble the travel motor by removing components like brackets, seals, springs, discs, plates, pistons, gears, and bearings. Corresponding illustrations accompany each step. Safety notices are also provided to properly handle fluids and prevent contamination.
Caterpillar cat 345 b lc excavator (prefix 7ks) service repair manual (7ks000...jfdskekdmme
The document provides instructions for disassembling and assembling the travel motor on 345B excavator models. It is a 15-step process that includes removing components like the brake cover, brake assembly, springs, seals, gears, and housing parts. Special tools are required and technicians must follow the steps carefully to avoid damaging parts and ensure proper reassembly.
Caterpillar cat 345 b lc excavator (prefix 7ks) service repair manual (7ks000...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor of a 345B L excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. Reassembly requires installing these parts in reverse order, taking care to align markings and ensure cleanliness to prevent contaminating the hydraulic system. Proper tools are required and safety precautions must be followed when handling springs and heavy components.
Caterpillar cat 345 b excavator (prefix 7ks) service repair manual (7ks00001 ...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor of a 345B L excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. Reassembly requires installing these parts in reverse order, taking care to align markings and ensure cleanliness to prevent contaminating the hydraulic system. Proper tools are required and safety precautions must be followed when handling springs and heavy components.
Caterpillar cat 345 b l excavator (prefix 7ks) service repair manual (7ks0000...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor of a 345B L excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. For assembly, it specifies cleaning parts and ensuring components are reinstalled in their original locations with proper lubrication to avoid damage. Proper containment of fluids is emphasized during maintenance.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
Caterpillar cat 345 b lc excavator (prefix 7ks) service repair manual (7ks000...jfdskekdmme
The document provides instructions for disassembling and assembling the travel motor on 345B excavator models. It is a 15-step process that includes removing components like the brake cover, brake assembly, springs, seals, gears, and housing parts. Special tools are required and technicians must follow the steps carefully to avoid damaging parts and ensure proper reassembly.
Caterpillar cat 345 b lc excavator (prefix 7ks) service repair manual (7ks000...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor of a 345B L excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. Reassembly requires installing these parts in reverse order, taking care to align markings and ensure cleanliness to prevent contaminating the hydraulic system. Proper tools are required and safety precautions must be followed when handling springs and heavy components.
Caterpillar cat 345 b excavator (prefix 7ks) service repair manual (7ks00001 ...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor of a 345B L excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. Reassembly requires installing these parts in reverse order, taking care to align markings and ensure cleanliness to prevent contaminating the hydraulic system. Proper tools are required and safety precautions must be followed when handling springs and heavy components.
Caterpillar cat 345 b l excavator (prefix 7ks) service repair manual (7ks0000...f8isoeidkdk
The document provides instructions for disassembling and assembling the travel motor of a 345B L excavator. It lists 32 steps for disassembly, including removing covers, springs, seals, gears, and housing components. For assembly, it specifies cleaning parts and ensuring components are reinstalled in their original locations with proper lubrication to avoid damage. Proper containment of fluids is emphasized during maintenance.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for removing and installing the lift cylinder and lift arms on a Caterpillar 420E backhoe loader. It includes:
- A list of required tools for each job.
- Step-by-step procedures to release hydraulic pressure, remove hoses and pins, and use tools to detach the lift cylinder and lift arms.
- Notes on cleaning parts and inspecting for wear before reassembly.
- An installation procedure that reverses the removal steps and includes torquing specifications.
Caterpillar Cat 374F L Excavator (Prefix DNM) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install components such as the ring gear, carrier assemblies, sun gears, and housing. Special precautions are mentioned regarding lifting heavy parts safely and using locking compounds on threaded fasteners. The overall procedure involves removing parts in the reverse order they were installed.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 420E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard and remove bolts to lower the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening new bolts, then raising the guard back into place.
Caterpillar Cat 374F L Excavator (Prefix NFJ) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and presents 37 steps to disassemble the various components of the final drive, including removing the ring gear, carrier assemblies, sun gears, and housing components. The assembly section lists 2 steps, including cleaning all parts and reassembling the final drive while applying anti-seize compound to bearing surfaces. Safety notes warn about ensuring puller studs meet hydraulic cylinder capacity when used.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for removing and installing the lift cylinder and lift arms on a Caterpillar 420E backhoe loader. It includes:
- A list of required tools for each job.
- Step-by-step procedures to release hydraulic pressure, remove hoses and pins, and use tools to detach the lift cylinder and lift arms.
- Notes on cleaning parts and inspecting for wear before reassembly.
- An installation procedure that reverses the removal steps and includes torquing specifications.
Caterpillar Cat 374F L Excavator (Prefix DNM) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install components such as the ring gear, carrier assemblies, sun gears, and housing. Special precautions are mentioned regarding lifting heavy parts safely and using locking compounds on threaded fasteners. The overall procedure involves removing parts in the reverse order they were installed.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 420E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard and remove bolts to lower the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening new bolts, then raising the guard back into place.
Caterpillar Cat 374F L Excavator (Prefix NFJ) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and presents 37 steps to disassemble the various components of the final drive, including removing the ring gear, carrier assemblies, sun gears, and housing components. The assembly section lists 2 steps, including cleaning all parts and reassembling the final drive while applying anti-seize compound to bearing surfaces. Safety notes warn about ensuring puller studs meet hydraulic cylinder capacity when used.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Required Tools
Tool Part Number Part Description Qty
(A) 1P-2420 Transmission Repair Stand 1
(B) 1P-1859 Pliers 1
(C) 1P-1863 Pliers 1
(D) 138-7575 Link Bracket 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Failure to properly assemble parts or failure to follow established
procedures can lead to damage to the parts and assembly.
To avoid damage to parts, always identify and mark the parts so that
they can be installed into the same location. Never force parts during
assembly. Keep parts clean and lubricated.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
2/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Illustration 1 g00633207
1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten travel motor
(1) to Tool (A). The weight of the travel motor is 125 kg (275 lb).
2. Put an alignment mark across all housings of the travel motor for assembly purposes.
3. Disconnect tube assembly (2) .
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
3/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00633208
Illustration 3 g00633209
4. Remove two socket head bolts (3) from the brake cover that are 180 degrees from each
other. Replace these two bolts with bolts that are slightly longer in length. The two longer
bolts will retain the brake cover when the remaining socket head bolts (3) are removed.
5. Evenly remove the remaining socket head bolts (3) that hold the brake cover in position.
Remove the two longer bolts (3). Remove brake cover (4) from the brake assembly.
4/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g00633210
6. If necessary, remove brake adjusting screws (5) from the brake cover.
Illustration 5 g00633212
7. Remove brake assembly (6) from the head assembly.
Illustration 6 g00633213
Note: There is an inner spring and an outer spring in each spring set.
8. Remove spring sets (7) from the brake piston.
5/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g00633214
9. Turn the brake housing to the other side. Remove O-ring seal (8) .
Illustration 8 g00633216
10. Use two suitable forcing screws (9) in order to remove brake piston (10) from the brake
housing.
Illustration 9 g00633217
6/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 11. Remove discs (11) and plates (12) .
Illustration 10 g00633218
12. Remove O-ring seal (13) .
13. Use Tool (B) in order to remove retaining ring (14). Remove gear (15) .
Illustration 11 g00633219
14. Use Tool (C) in order to remove retaining ring (16) .
15. Remove the nut and bushing (17) from the rod assembly.
16. Remove four socket head bolts (18) that hold the head assembly to the motor housing.
7/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g00633220
17. Fasten Tool (D) and a hoist to head assembly (19), as shown. Carefully remove the head
assembly from the motor housing. The weight of the head assembly is 25 kg (55 lb).
Illustration 13 g00633221
18. Remove thrust plate (20) from the head.
Illustration 14 g00633223
8/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 19. Remove O-ring seal (22) from the head.
20. Remove bearing (23) from the head.
21. Remove pin (21) from the head.
Illustration 15 g00633224
22. Remove O-ring seal (25) from the motor housing.
23. Turn the motor housing on the side, as shown.
Note: Keep the components together, while you remove the barrel assembly from the motor
housing. All parts in the barrel assembly must be reinstalled in the original locations.
24. Carefully remove barrel assembly (24) from the motor housing so the components do not
come apart.
25. Disassemble barrel assembly (24), as follows:
Illustration 16 g00633225
a. Place identification marks on piston assemblies (27), retainer (26), and barrel (28).
Remove piston assemblies (27), and retainer (26) from barrel (28) .
9/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. b. Separate piston assemblies (27) from retainer (26) .
Illustration 17 g00633227
c. Remove guide (29) from the barrel.
Illustration 18 g00633228
Note: Take note of the shims (30) that are positioned on the barrel for installation
purposes.
d. Remove shims (30) from the barrel.
10/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g00633230
26. Remove adjusting screw (31) from the motor housing. Remove the O-ring seal from the
adjusting screw.
27. Remove swashplate assembly (32) from the motor housing.
28. Disassemble the swashplate assembly, as follows:
Illustration 20 g00633231
a. Remove plate (33) .
11/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 21 g00633232
b. Remove three pins (34) from the plate.
c. Remove two screws (35) .
d. Remove plate (36) .
e. Remove two plungers (37) .
Illustration 22 g00633235
29. Use Tool (B) in order to remove retaining ring (38) that holds shaft assembly (39) in the
motor housing.
Illustration 23 g00633238
30. Use a soft faced hammer in order to remove shaft assembly (39) from the motor housing in
the direction that is shown.
31. Disassemble shaft assembly (39), as follows:
12/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 24 g00633239
a. Remove O-ring seal (40) from cover (41) .
b. Remove cover (41) from the shaft.
Illustration 25 g00633241
c. Remove lip seal (42) from cover (41) .
Illustration 26 g00633243
13/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. d. Use Tool (C) in order to remove retaining ring (43) that holds bearing (44) in position
on the shaft.
Illustration 27 g00633245
e. Put the shaft in a press, as shown. Press the shaft out of bearing (44) .
Illustration 28 g00633246
32. Remove two screws (47) and two bearings (46) from the motor housing. Remove two
bushings (45) from the motor housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 20 01:16:40 UTC+0800 2020
14/14
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B L EXCAVATOR 4SS
Configuration: 345B and 345B L Excavators 4SS00001-UP (MACHINE)
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i03721001
Travel Motor - Assemble - Series I
SMCS - 4351-016
S/N - 2NW1-UP
S/N - 2SW1-UP
S/N - 2ZW1-UP
S/N - 3MW1-UP
S/N - 4SS1-UP
S/N - 5WS1-UP
S/N - 6MW1-UP
S/N - 6XS1-UP
S/N - 7KS1-UP
S/N - 8KW1-UP
S/N - 8RW1-UP
S/N - 9CW1-UP
S/N - 9GS1-UP
S/N - BFG1-UP
Installation Procedure
Table 1
1/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Required Tools
Tool Part Number Part Description Qty
(A) 1P-2420 Transmission Repair Stand 1
(B) 1P-1859 Pliers 1
(C) 1P-1863 Pliers 1
(D) 138-7575 Link Bracket 2
(E) 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound during the
assembly procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
2/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00633246
1. Use Tool (E) in order to install two bushings (45) in the motor housing. Install the bushings
until the bushings are seated in the motor housing.
2. Put two bearings (46) in position in the motor housing, as shown.
3. Put 9S-3263 Thread Lock Compound on the threads of two screws (47) .
4. Install the two screws, and tighten the screws to a torque of 5 N·m (44 lb in).
5. Assemble shaft assembly (39) , as follows:
Illustration 2 g00633243
a. Heat bearing (44) . Install the bearing until the bearing makes contact with the
shoulder on the shaft.
b. Use Tool (C) in order to install retaining ring (43) .
3/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g00633241
c. Use Tool (E) in order to install lip seal (42) in cover (41) .
d. Install the seal until the seal makes contact with the counterbore in the cover and with
the sealing lip facing toward the inside. Lubricate the lip of the seal with clean
hydraulic oil.
Illustration 4 g00633239
e. Install cover (41) on the shaft, as shown.
f. Install O-ring seal (40) on the cover. Lubricate the O-ring seal with clean hydraulic
oil.
4/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 5 g00633235
6. Use a soft faced hammer in order to install shaft assembly (39) in the motor housing. Make
sure that the shaft assembly is seated in the motor housing.
7. Use Tool (B) in order to install retaining ring (38) in the motor housing.
8. Assemble the swashplate assembly, as follows:
Illustration 6 g00633232
a. Install two plungers (37) .
b. Install plate (36) .
c. Install two screws (35) .
d. Install three pins (34) in the plate.
5/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 7 g00633231
e. Install plate (33) .
Illustration 8 g00633230
9. Install swashplate assembly (32) in the motor housing, as shown.
10. Install the O-ring seal on adjusting screw (31) . Install the screw for adjusting in the motor
housing.
11. Assemble barrel assembly (24) , as follows:
6/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 9 g00633228
a. Install the original amount of shims (30) on the barrel. Make sure that the shims are
installed in the original positions.
Illustration 10 g00633227
b. Install guide (29) on the barrel, as shown. Make sure that the guide is seated squarely.
Illustration 11 g00633225
c. Install nine piston assemblies (27) in the original location in retainer (26) .
d. Install the piston assemblies with the retainer in the original location in the barrel.
7/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 12 g00633227
Note: Make sure that the barrel assembly (24) does not fall apart during installation in the
motor housing.
Illustration 13 g02005414
12. Carefully install barrel assembly (24) over the shaft in the motor housing. Make sure that
the components of the barrel assembly do not fall apart during installation. Install lip type
seal (25A) .
13. Install O-ring seal (25) in the motor housing.
8/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 14 g00633223
14. Install pin (21) in the head.
15. Install bearing (23) in the head. Make sure that the bearing makes contact with the
counterbore in the head during installation.
16. Install O-ring seal (22) in the head.
Illustration 15 g00633221
17. Install thrust plate (20) on the head, as shown.
9/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 16 g00633220
18. Fasten Tool (D) and a hoist to head assembly (19) , as shown. Carefully put the head
assembly in the original position on the motor housing.
Illustration 17 g00633219
19. Put 9S-3263 Thread Lock Compound on the threads of four socket head bolts (18) .
20. Install four socket head bolts (18) that hold the head assembly to the motor housing.
21. Put 9S-3263 Thread Lock Compound on the threads of bushing (17) .
22. Install the bushing and the nut on the rod assembly in the motor housing.
23. Use Tool (C) in order to install retaining ring (16) on the shaft.
10/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 18 g00633416
24. Put gear (15) in position on the shaft. Use Tool (B) in order to install retaining ring (14) .
This will hold the gear in position.
25. Install O-ring seal (13) in the head assembly.
Illustration 19 g00633421
26. Install discs (11) and plates (12) in alternating order. Start with a disc and end with a disc.
11/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 20 g00633417
27. Install brake piston (10) in the brake housing.
Illustration 21 g00633214
28. Turn the brake housing on the other side. Install O-ring seal (8) in the brake housing.
Illustration 22 g00633423
Note: There is an inner spring and an outer spring in each spring set.
29. Install spring sets (7) in the brake piston.
12/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Illustration 23 g00633424
30. Install brake assembly (6) in the head assembly, as shown.
Illustration 24 g00633426
31. Reinstall the screw for the brake adjustment (5) in the brake cover.
Illustration 25 g00633209
13/15
345B and 345B L Excavators 4SS00001-UP (MACHINE)(SEBP2693 - 68) - Docu...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...