Comandos para vo ip

1. COMANDOS PARA VoIP
COMANDOS A SEREM APLICADOS NO ROUTER:
CONFIGURAÇÕES DA INTERFACE:
Router>enable
Router#configure terminal
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip add 200.100.10.1 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#exit
Router#wr
Building configuration...
[OK]
CONFIGURAÇÃO DO ESCOPO DE VOZ:
Router#configure terminal
Router(config)#ip dhcp pool voice
Router(dhcp-config)#network 200.100.10.0 255.255.255.0
Router(dhcp-config)#default-router 200.100.10.1
Router(dhcp-config)#option 150 ip 200.100.10.1
Router(dhcp-config)#exit
Router(config)#ip dhcp excluded-address 200.100.10.1
Router(config)#exit
Router#wr
Building configuration...
[OK]
CONFIGURAÇÃO DO SERVIÇO DE TELEFONE:
Router(config)#telephony-service
Router(config-telephony)#max-dn 5
Router(config-telephony)#max-ephones 5
Router(config-telephony)#ip source-address 200.100.10.1 port 2000
Router(config-telephony)#exit
Router(config)#exit
Router#wr
Building configuration...
[OK]
COONFIGURANDO OS TELEFONES E ATRIBUINDO OS RAMAIS:
Router>ena
Router#configure terminal
Router(config-ephone-dn)#ephone-dn 1
Router(config-ephone-dn)#number 54001
Router(config-ephone-dn)# ephone-dn 2
Router(config-ephone-dn)#number 54002
Router(config-ephone-dn)#exit
Router (config-ephone)# ephone 1
Router (config-ephone)# Mac-address x.x.x
Router (config-ephone)# Type 7962/CIPC -> (Referente a Desktop e telephony
physical)

2. COMANDOS PARA VoIP
Router (config-ephone)# Button 1:1 (O primeiro número se refere a ao botão
físico do telefone e o segundo ao ID do ephone-dn)
Router (config-ephone)# ephone 2
Router (config-ephone)# Mac-address x.x.x
Router (config-ephone)# Type 7962/CIPC -> (Referente a Desktop e telephony
physical)
Router (config-ephone)# Button 1:2 (O primeiro número se refere a ao botão
físico do telefone e o segundo ao ID do ephone-dn)
Router(config)#do wr
Building configuration...
[OK]
CONFIGURANDO ROTEAMENTO ENTRE VoIP:
Router(config)# dial-peer voice 1 voip (Definir um correspondente de discagem
pel metodo de encapsulamento de voz)
Router(config-dial-peer)# destination-pattern 12... (Especificar o prefix ou o
numero E 164 completo a ser usado para o correspondente de discagem).
Router(config-dial-peer)#session target ipv4: 10.0.0.2 (Designar o endereço
especifico de rede para o recebimento de chamadas do correspondente de
discagem em voz por ip).
Router(config-dial-peer)# exit
Router(config)do wr
Building configuration...
[OK]
SYSTEM MESSAGE (MENSAGEM DO SISTEMA)
Router(config)# telephony-service
Router(config-telephony)# System message SUA MENSAGEM
NAME/LABEL (NOME/RÓTULO)
Router(config)# ephone-dn X
Router(config-ephone-dn)# name fulano
Router(config-ephone-dn)# label fulano
PAGING(UTILIZAR ENDEREÇO MULTICAST)
Router(config)# ephone-dn 4
Router(config-ephone-dn)# number 999
Router(config-ephone-dn)# paging ip 239.2.2.2 port 2000
Router (config)# ephone 1
Router(config-ephone)# paging-dn 4
Router (config)# ephone 2
Router(config-ephone)# paging-dn 4
Router (config)# ephone 3
Router(config-ephone)# paging-dn 4
CALL MONITOR
Router(config)# ephone 3
Router(config-ephone)# button 3m1

3. COMANDOS PARA VoIP
CALL FORWARD (BUSY) OCUPADO
Router (config)# telephony-service
Router(config-telephony)# call-forward system redirecting-expanded
Router(config)# ephone-dn 2
Router(config-ephone-dn)# call-forward busy 1100
CALL FORWARD (NOAN) – SEM RESPOSTA
Router (config)# telephony-service
Router(config-telephony)# call-forward system redirecting-expanded
Router(config)# ephone-dn 1
Router(config-ephone-dn)# call-forward noan 120 timeout 15
CALL PARK
Router(config)# telephony-service
Router(config-telephony)# call-park system application
Router (config)# ephone-dn 7
Router(config-ephone-dn)# number 555
Router(config-ephone-dn)# park-slot
par-slot timeout x limit y recall retry s limit z -> Números.
Ephone-dn 7 dual-line
number 3010
name Call park
par-slot reserved-for 3010
Ephone-dn 10
transfer-park bocked
MOH (MUSIC ON HOLD)
Router(config)# telephony-service
Router(config-telephony)# moh flash:music.wav
COMANDOS A SEREM APLICADOS NO SWITCH:
CONFIGURANDO E ATRIBUINDO INTERFACES A VLAN:
Switch>enable
Switch#configure terminal
Switch(config)#interface range fastEthernet 0/1-5
Switch(config-if-range)#switchport voice vlan 1
Switch(config-if-range)#exit
Switch(config)#exit
Switch#wr
Building configuration...
[OK]
Switch#configure terminal
Switch(config)#vlan 2
Switch(config-vlan)#name EDUC
Switch(config-vlan)#END
Switch#SHow VLan Brief

4. COMANDOS PARA VoIP
Switch#configure terminal
Switch(config-if)#INTerface FastEthernet 0/13
Switch(config-if)#SWitchport ACCess VLAN 2
Switch(config-if)#EXIT
Switch(config)#EXIT
Switch#SHow VLan Brief
Switch#Wr
Building configuration...
[OK]