9. INTRODUCTION
Foreword - Important notice regarding equipment servicing
TC Harvest Suit™ Comfort Cab WE
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your NEW HOLLAND Sales and Service Networks.
48001074 29/04/2016
3
10. INTRODUCTION
Safety rules
TC Harvest Suit™ Comfort Cab WE
LEGAL OBLIGATIONS
This machine may be equipped with special guarding or other devices in compliance with local legislation. Some to
these require active use by the operator. Therefor, check local legislations on the usage of this machine.
ACCIDENT PREVENTION
Most accidents or injuries that occur in workshops are the result of non compliance to simple and fundamental safety
principles. For this reason, IN MOST CASES THESE ACCIDENTS CAN BE AVOIDED by applying the fundamental
safety principles, acting with the necessary caution and care.
Accidents may occur with all types of machine, regardless of how well the machine in question was designed and
built.
CAUTION
Unexpected machine movement!
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or
raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in minor or
moderate injury.
C0038A
SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND COMPONENTS - HY-
DRAULICS (EUROPEAN STANDARD EN982)
• Flexible hose assemblies must not be constructed from hoses which have been previously used as part of a hose
assembly.
• Do not weld hydraulic pipes: when flexible hoses or piping are damaged, replace them immediately.
• It is forbidden to modify a hydraulic accumulator by machining, welding or any other way.
• Before removing hydraulic accumulators for servicing, the liquid pressure in the accumulators must be reduced to
zero.
• Pressure check on hydraulic accumulators must be carried out by a method recommended by the accumulator
manufacturer.
• Take care not to exceed the maximum allowed pressure of the accumulator. After any check or adjustment, check
for leakages or gas in the hoses or tubes.
SAFETY RULES
General guidelines
• Carefully follow specified repair and maintenance procedures.
• When appropriate, use P.P.E (Personal Protective Equipment)
• Do not wear rings, wristwatches, jewellery, unbuttoned or loose articles of clothing such as: ties, torn clothing,
scarves, open jackets or shirts with open zips that may remain entangled in moving parts. It is advised to wear
approved safety clothing, e.g.: non-slip footwear, gloves, safety goggles, helmets, etc.
• Do not carry out repair operations with someone sitting in the driver's seat, unless the person is a trained technician
who is assisting with the operation in question.
• Do not operate the machine or use any of the implements from different positions, other than the driver's seat.
48001074 29/04/2016
4
11. INTRODUCTION
• Do not carry out operations on the machine with the engine running, unless specifically indicated.
• Bring all hydraulic cylinders to the home positions (down, retracted, etc.) before engine shut down.
• Stop the engine and check that the hydraulic circuits are pressure-free before removing caps, covers, valves, etc.
• All repair and maintenance operations must be carried out using extreme care and attention.
• Service steps and platforms used in the workshop or elsewhere should be built according to the applicable stan-
dards and legislation.
• Disconnect the Power Take-Off (PTO) and label the controls to indicate that the machine is being serviced.
• Brakes are inoperative when manually released for repair or maintenance purposes. Use blocks or similar devices
to secure the machine in these conditions.
• Only use specified towing points for towing the machine. Connect parts carefully. Make sure that all pins and/or
locks are secured in position before applying traction. Never remain near the towing bars, cables or chains that are
operating under load.
• When loading or unloading the machine from the trailer (or other means of transport), select a flat area capable of
sustaining the trailer or truck wheels. Firmly secure the machine to the truck or trailer and lock the wheels in the
position used by the carrier.
• Electric heaters, battery-chargers and similar equipment must only be powered by auxiliary power supplies with
efficient ground insulation to avoid electrical shock hazards.
• Always use suitable hoisting or lifting devices when raising or moving heavy parts.
• Keep bystanders away.
• Never use gasoline, diesel oil or other inflammable liquids as cleaning agents. Use non-inflammable, non toxic
commercially available solvents.
• Wear safety goggles with side guards when cleaning parts with compressed air.
• Never use open flames for lighting when working on the machine or checking for leaks.
• When carrying out checks with the engine running, request the assistance of an operator in the driver's seat. The
operator must maintain visual contact with the service technician at all times.
• If operating outside the workshop, position the machine on a flat surface and lock in position. If working on a slope,
lock the machine in position. Move to a flat area as soon as is safely possible.
• Maintenance and repair operations must be carried out in a clean and dry area. Clean up any water or oil spillage
immediately.
• Do not create piles of oil or grease-soaked rags as they represent a serious fire hazard. Always store rags in a
closed metal container.
• Before engaging the machine, make sure that there are no persons within the machine or implement range of action.
• Empty your pockets of all objects that may fall accidentally unobserved into the machine inner compartments.
• When metal parts are sticking out, use protective goggles or goggles with side guards, helmets, special footwear
and gloves.
• When welding, use protective safety devices: tinted safety goggles, helmets, special overalls, gloves and footwear.
All persons present in the area where welding is taking place must wear tinted goggles. NEVER LOOK DIRECTLY
AT THE WELDING ARC WITHOUT SUITABLE EYE PROTECTION.
48001074 29/04/2016
5
13. Engine - Engine air compressor
Air compressor - Static description
TC5.80 WE
TC5.90 Hillside WE
TC5.90 WE
The air compressor (3) is a single cylinder, gear driven air compressor, which supplies air to a reservoir tank, enabling
the operator to have a source of compressed air for cleaning purposes and tyre inflation. The compressor is mounted
directly on the engine with the two nuts (10).
Engine oil is supplied through an internal connection with the engine, using engine oil pressure to lubricate the com-
pressor.
The compressed air is delivered through tubing to a combination pressure relief control valve, and from there to the
reservoir tank located on the straw hood of the combine. A quick disconnect fitting allows easy connection to the air
supply for blow off nozzles as well as for tyre inflation equipment.
ZEIL06CS0085A0B 1
48001074 29/04/2016
10.1 [10.450] / 3
14. Engine - Engine air compressor
Air compressor - Drawing
TC5.80 WE
TC5.90 Hillside WE
TC5.90 WE
ZEIL11CX0668G0B 1
Reference Port Port Name Port Function
1 0 Inlet Port Supplies Compressor with clean intake air
2 2 Discharge Port Expels pressurized air for system
4 8.1 Oil Supply Supplies compressor with lube oil from engine
5 8.2 Oil Drain Allows lube oil to return to engine
6 9.1 Coolant Receive coolant from engine
7 9.2 Coolant Return coolant to engine
48001074 29/04/2016
10.1 [10.450] / 4
15. Engine - Engine air compressor
Compressed air tank Relief valve - Drawing
TC5.80 WE
TC5.90 Hillside WE
TC5.90 WE
ZEIL11CX0667G0B 1
Reference Port Port name Port function
1 1 Inlet Pressurized air "in" from compressor
2 21 Outlet Pressurized air "out" to reservoir tank and blow
off line quick connect port
3 22 Auxiliary supply Auxiliary port not used in this application
4 1-2 Tire inflation device Port used to connect tire inflation device
5 3 Exhaust for compressor idling Discharge exhaust for excess pressure in system
48001074 29/04/2016
10.1 [10.450] / 5
16. Engine - Engine air compressor
Compressed air tank Relief valve - Static description
TC5.80 WE
TC5.90 Hillside WE
TC5.90 WE
The pressure relief valve is developed to protect the system against pressures higher than 8 bar ( 116 psi).
Port (1) is connected to the air compressor, port (21) is connected to the pressurized reservoir.
When the pressure on port (21) reaches 8 bar ( 116 psi), the control valve (9d) will be activated which means that
also control valve (9c) will be activated. The pressure from the compressor will now pass through port (3).
If the pressure drops below 8 bar ( 116 psi) by activation a engaging valve, control valve (9d) will close.
Valve (9c) will not close immediately but will remain in the open position until the pressure exerted on the control of
valve (9c) will be reduced by 0.6 bar ( 8.7 psi). Then the air will pass through valve (9b).
Schematic diagram
ZDA7672Z 1
48001074 29/04/2016
10.1 [10.450] / 6
17. Engine - Engine air compressor
Air compressor - Remove
TC5.80 WE
TC5.90 Hillside WE
TC5.90 WE
1. Bleed the air from the system by opening the drain (2)
at the bottom of the air reservoir.
ZEIL06TC00034A0 1
2. Loosen the retaining strap (1) and remove the air inlet
pipe (2) from the air compressor (3).
NOTE: Protect the air inlet and outlet ports from dirt
ingress.
3. Loosen the connection (4) to remove the hose (5) from
the air compressor (3).
ZEIL06CS0082A0B 2
4. Drain sufficient coolant from the engine cooling system
to allow removal of the coolant lines.
NOTE: Refer to the Operator’s Manual of your machine.
5. Loosen the connection (6).
ZEIL06CS0083A0B 3
48001074 29/04/2016
10.1 [10.450] / 7
18. Engine - Engine air compressor
6. Loosen the connection (7).
7. Remove the four bolts (8) to remove the support (9).
ZEIL06CS0084A0B 4
8. Remove the two nuts (10) to remove the air compressor
(3) from the engine.
ZEIL06CS0085A0B 5
48001074 29/04/2016
10.1 [10.450] / 8
19. Engine - Engine air compressor
Air compressor - Install
TC5.80 WE
TC5.90 Hillside WE
TC5.90 WE
1. Install the air compressor (3) on the engine and tighten
the two nuts (10).
ZEIL06CS0085A0B 1
NOTE: Make sure that the O-ring (11) is positioned well. If
necessary apply grease.
ZEIL06CS0086A0B 2
2. Install the support (9) with the four bolts (8).
3. Install the tube and tighten the connection (7).
ZEIL06CS0084A0B 3
48001074 29/04/2016
10.1 [10.450] / 9
20. Engine - Engine air compressor
4. Install the tube and tighten the connection (6).
ZEIL06CS0083A0B 4
5. Install the hose (5) on the air compressor (3) and
tighten the connection (4).
6. Install the pipe (2) on the air compressor (3) and tighten
the retaining strap (1).
ZEIL06CS0082A0B 5
7. Close the drain (2) at the bottom of the reservoir.
8. Add engine coolant to the cooling system, refer to the
Operator’s Manual for more details.
9. Start the engine to charge the system with air. Allow the
air system to build up pressure to the governor cutout.
Stop the engine and use a soap and water solution at
the connection points to check for air leaks. Make any
necessary repairs.
ZEIL06TC00034A0 6
48001074 29/04/2016
10.1 [10.450] / 10
21. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
Selective Catalytic Reduction (SCR) exhaust treatment - Remove
- Exhaust flap
1. Drain the coolant reservoir. See the operator’s manual.
2. Loosen the screw (1) and open the clamp.
3. Loosen the screw (3) and open the clamp.
4. Remove the elbow (2) together with the flexible cou-
pling from between the Diesel Oxidation Catalyst
(DOC) and the exhaust flap.
NOTE: Make sure you do not lose the gasket located be-
tween the elbow and the DOC and the gasket located be-
tween the flexible coupling and the exhaust valve.
ZEIL15TC00321AA 1
5. Undo the snap buttons of the heat resistant sleeve (5)
to access and disconnect the connector (6).
6. Disconnect the water inlet (8) from the exhaust flap (4)
(from water pump to exhaust flap).
7. Disconnect the water outlet (7) from the exhaust flap
(4) (from exhaust flap to engine).
ZEIL15TC00322AA 2
8. Loosen the screw (9) and open the clamp.
9. Remove the hardware (11) (four in total), the support
(10), and the exhaust flap (4).
ZEIL15TC00323AA 3
48001074 29/04/2016
10.2 [10.500] / 3
22. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
Selective Catalytic Reduction (SCR) exhaust treatment - Install
- Exhaust flap
1. Install the exhaust flap (4) on the outlet manifold. Make
sure the gasket between the turbo and the exhaust flap
(4) is properly installed. Use the hardware (11) (four in
total) and the support (10), do not tighten yet.
2. Orient the clamp as shown. Close the clamp and torque
the screw (9) between 5 - 7 N·m (3.7 - 5.2 lb ft).
3. Torque the hardware (11) to 25 N·m (18.4 lb ft).
ZEIL15TC00323AA 1
4. Connect the water outlet (7) to the exhaust flap (4)
(from exhaust flap to engine). Torque to 20 N·m
(14.8 lb ft).
5. Connect the water inlet (8) to the exhaust flap (4) (from
water pump to exhaust flap). Torque to 20 N·m (14.8 lb
ft).
6. Connect the connector (6). Close the snap buttons of
the heat resistant sleeve (5) and make sure it protects
the connector (6) and wire harness properly.
ZEIL15TC00322AA 2
7. Install the elbow (2) together with the flexible coupling
between the Diesel Oxidation Catalyst (DOC) and the
exhaust flap. Make sure the gasket between the elbow
and the DOC, and the gasket between the flexible cou-
pling and the exhaust flap are properly installed.
8. Orient the screw (1) of the clamp as shown. Torque the
screw (1) between 6 - 8 N·m (4.4 - 5.9 lb ft).
9. Orient the screw (3) of the clamp as shown. Torque the
screw (3) between 6 - 8 N·m (4.4 - 5.9 lb ft).
ZEIL15TC00321AA 3
10. Fill the coolant reservoir. See the operator’s manual.
48001074 29/04/2016
10.2 [10.500] / 4
23. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
Selective Catalytic Reduction (SCR) muffler and catalyst - Remove
1. Behind the oil reservoir, cut the straps (1).
2. Disconnect the connector (2A).
ZEIL15TC00317AA 1
3. Remove the NH3 sensor (2).
4. Remove the temperature sensor (4).
5. Remove the NOx sensor (5).
6. Loosen the clamp (3).
7. Remove the hardware that mounts the clamp (6) to the
Diesel Oxidation Catalyst (DOC).
ZEIL15TC00316AA 2
8. Remove the temperature sensor (10).
9. Loosen the clamp (7).
10. Remove the hardware (8) of the clamp.
11. Remove the air suction tube (9).
ZEIL15TC00318AA 3
12. Remove the hardware (11) and the plate (12).
13. Remove the hardware (14) and the heat shield (13).
ZEIL15TC00318AA 4
48001074 29/04/2016
10.2 [10.500] / 5
24. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
14. Remove the hardware (16) and the heat shield (15).
ZEIL15TC00313AA 5
15. Remove the bolt (18) of both straps (17).
ZEIL15TC00319AA 6
16. Loosen the screw of the clamp (20) and open the
clamp (20).
17. Loosen the screw of the clamp (21) and open the
clamp (21).
18. Remove the tube (19). Make sure you do not lose the
gasket between the DOC and the tube (19) and the
gasket between the tube (19) and the muffler (22).
ZEIL15TC00320AA 7
19. Loosen the clamp (23) and remove the exhaust tube
(24).
20. Remove the muffler (22). Use a suitable lifting device.
ZEIL16TC00062AA 8
48001074 29/04/2016
10.2 [10.500] / 6
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
Selective Catalytic Reduction (SCR) muffler and catalyst - Install
1. Install the muffler (22). Use a suitable lifting device.
2. Install the exhaust tube (24) and the clamp (23) on the
muffler, torque between 40 - 50 N·m (29.5 - 36.9 lb ft).
ZEIL16TC00062AA 1
3. Install the tube (19). Make sure the gasket between the
Diesel Oxidation Catalyst (DOC) and the tube (19), and
the gasket between the tube (19) and the muffler (22)
are properly installed.
4. Close the clamp (21) and torque between 18 - 22 N·m
(13.3 - 16.2 lb ft).
5. Orient the clamp (20) with the screw on the underside
and in a horizontal position. Close the clamp (20) and
torque between 6 - 8 N·m (4.4 - 16.2 lb ft).
ZEIL15TC00320AA 2
6. Tighten the bolt (18) of both straps (17).
ZEIL15TC00319AA 3
7. Install the heat shield (15). Use the hardware (16).
ZEIL15TC00313AA 4
48001074 29/04/2016
10.2 [10.500] / 7
27. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
8. Install the heat shield (13). Use the hardware (14).
9. Install the plate (12). Use the hardware (11).
ZEIL15TC00318AA 5
10. Install the air suction tube (9). Use the hardware (8).
11. Install the hardware that mounts the clamp (6) to the
DOC. See Figure 7.
12. Tighten the clamp (7).
13. Tighten the clamp (3). See Figure 7.
14. Install the temperature sensor (10). Torque between
40 - 50 N·m (29.5 - 36.9 lb ft).
ZEIL15TC00318AA 6
15. Install the temperature sensor (4). Torque between 40
- 50 N·m (29.5 - 36.9 lb ft).
16. Install the NOx sensor (5), apply WEICON HIGH-TECH
ASSEMBLY PASTE on the threads. Torque between 40
- 60 N·m (29.5 - 44.3 lb ft).
17. Install the NH3 sensor (2), apply LOCTITE® X203 DRY
FILM MOLY ANTI-SEIZE on the threads. Torque be-
tween 40 - 60 N·m (29.5 - 44.3 lb ft).
ZEIL15TC00316AA 7
18. Connect the connector (2A).
19. Tie up the cables of the sensors. Use the straps (1).
NOTICE: Do not use straps on the protection tube of the
NH3 sensor. This piece must have a minimum bend radius
of 50 mm (2 in) at a 90 ° maximum bend angle.
ZEIL15TC00317AA 8
48001074 29/04/2016
10.2 [10.500] / 8
28. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
Diesel Exhaust Fluid (DEF)/AdBlue® filters - Service instruction
Main filter
1. On the supply module (1). Remove the filter cover (2),
turn counter-clockwise.
NOTE: Required tool : 27 mm wrench.
ZEIL15TC00307AA 1
2. Remove the equalizing element (3).
ZEIL15TC00308AA 2
3. Check the color of the filter (4) inside.
ZEIL15TC00309AA 3
4. Choose the correct side of the tool (5) that comes with
the replacement filter.
• (B) side for black filter.
• (G) side for grey filter.
ZEIL15TC00310AA 4
48001074 29/04/2016
10.2 [10.500] / 9
29. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
5. Insert the correct side of the tool (5) into the filter (4)
until a click is noticed.
6. Pull out the filter (4) with the tool (5) by hand. If nec-
essary insert a screwdriver in the slot of the tool (5) to
help extract the filter (4).
ZEIL15TC00311AA 5
7. Clean functional surfaces indicated by the arrow with
clean water only.
NOTE: Protect the filter chamber from contamination and
particles.
8. Lubricate the O-rings (6) with MOBIL VELOCITE™ NO. 6
OIL and insert the new filter (4) into the supply module
(1).
ZEIL15TC00312AA 6
9. Insert the new equalizing element (3).
ZEIL15TC00308AA 7
10. On the supply module (1). Install the filter cover (2),
clockwise. Torque to 15 - 25 N·m (132.8 - 221 lb in).
ZEIL15TC00307AA 8
48001074 29/04/2016
10.2 [10.500] / 10
30. Engine - Selective Catalytic Reduction (SCR) exhaust treatment
In-line filter
11. Remove the cover (2) from the housing (1).
NOTE: Required tools: 24 mm and 27 mm wrench.
ZEIL16TC00023AA 9
12. Remove the spacer (3) from the housing (1).
13. Remove the filter (4) from the cover (2).
ZEIL16TC00003AA 10
14. Clean the housing (1), the spacer (3) and the cover
(2) with clean water only.
15. Check the O-ring (5) and the O-ring (6) for damage,
replace if necessary.
ZEIL16TC00003AZ 11
16. Install the new filter (4) on the cover (2).
17. Install the spacer (3) inside the housing (1).
ZEIL16TC00003AA 12
48001074 29/04/2016
10.2 [10.500] / 11
