Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (bdy02001 and up)

Service Repair Manual
Models
M322C WHEELED Excavator

Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M322C WHEELED EXCAVATOR BDY
Configuration: M322C Excavator BDY02001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M318C MH and M322C MH Excavators Power Train
Media Number -RENR7011-03 Publication Date -01/10/2006 Date Updated -25/10/2006
i04706197
Final Drive Carriers, Hubs and Brakes - Disassemble - Front
Axle
SMCS - 4054-015; 4092-015; 4253-015; 4255-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 147-1744 Bearing Puller 1
B 1P-0510 Driver Gp 1
C 1P-1859 Retaining Ring Pliers 1
D 5F-4764 Pry Bar 2
E
6V-6080 Torque Multiplier Gp 1
4C-4061 Center Ring 1
4C-4058 Spanner 1
F 1U-6415 Three Jaw Puller 1
G 1U-6405 Three Jaw Puller 1
H 1P-1853 Retaining Ring Pliers 1
J 1U-8758 Retaining Ring Pliers 1
ZZ
6V-9508 Face Seal Plug 1
6V-9829 Cap As 1
1/13(W)w
2020/3/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Start By:
A. Remove the tire and rim (front). Refer to Disassembly and Assembly, "Tire and Rim -
Remove (Front)".
B. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
At operating temperature, the hydraulic oil is hot and under pressure.
Hot oils can cause burns.
To prevent possible personal injury, release the pressure in the work
tool hydraulic circuit (boom, stick, bucket, and swing), travel circuits,
and the hydraulic oil tank at the filler cap before any hydraulic lines or
components are disconnected or removed.
Remove the filler cap only when the engine is stopped and the filler cap
is cool enough to touch.
1. Drain the front final drives. Final drives with oil cooled disc brakes have approximately 2.0
L (.5 US gal).
2/13(W)w

Illustration 1 g01137933
2. Attach a suitable lifting device to carrier housing (2) .
3. Remove retaining bolts (1) .
4. Remove carrier housing (2) . The weight of carrier housing (2) is approximately 25 kg (55
lb).
5. Disconnect hose assembly (3) and plug.
3/13(W)w

6. Use Tooling (C) in order to remove retaining ring (4) .
7. Use Tooling (D) in order to remove planetary gears (5) from the housing.
8. Remove thrust washer (6) .
9. Remove retaining rings (8) and the washers from planetary gear (5) .
10. Remove roller bearing (7) from planetary gear (5) .
4/13(W)w

11. Use Tooling (H) in order to remove retaining ring (9) .
12. Remove washer (10) .
13. Remove hex bolt (11) .
5/13(W)w

14. Remove sun gear (13) .
15. Remove gear (12) .
16. Use Tooling (J) in order to remove retaining ring (14) .
18. Remove four discs (16) and three plates (17) .
6/13(W)w

20. Remove lockring (19) from spanner nut (20) .
21. Install Tooling (E) .
7/13(W)w

22. Install Tooling (E) in order to remove spanner nut (20) .
23. Install Tooling (F) , Tooling (B) , and a suitable lifting device in order to remove ring gear
assembly (21) .
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Remove nuts (22) and brake piston (23) from ring gear assembly (21) .
8/13(W)w

25. Remove bolts (24) and the springs from ring gear assembly (21) .
26. Remove O-ring seal (25) and the backup ring.
27. Remove retaining ring (26) from the gear assembly.
9/13(W)w

28. Use a hammer and a punch in order to remove brake piston (23) and ring (27) from ring
gear assembly (21) .
29. Remove seals (28) .
30. Remove backup rings (29) .
31. Remove O-ring seal (30) from hub assembly (31) .
32. Remove O-ring seal (32) , and the O-ring seal from spindle (33) .
10/13(W)w

33. Attach Tooling (F) , Tooling (B) , and a suitable lifting device in order to remove hub
assembly (31) .
34. Remove hub assembly (31) .
Note: When hub (31) is removed from the spindle the outer bearing cone (34) will be loose.
35. Remove bearing cone (34) from hub assembly (31) .
11/13(W)w

36. Remove inner bearing cup (35) from hub assembly (31) .
37. Remove seal (37) from hub assembly (31) .
38. Remove outer bearing cup (36) from hub assembly (31) .
12/13(W)w

39. Remove spacer (38) from spindle (33) .
40. Install Tooling (G) , Tooling (B) , and Tooling (A) .
41. Remove inner bearing cone (39) from the spindle.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 28 15:36:47 UTC+0800 2020
13/13(W)w

Shutdown SIS
Previous Screen
i02250735
Final Drive Carriers, Hubs and Brakes - Disassemble - Rear
Axle
SMCS - 4054-015; 4092-015; 4253-015; 4255-015
Disassembly Procedure
Table 1
Required Tools
A 6V-8336 Bolt 2
B 1P-1859 Retaining Ring Pliers 1
C 5F-4764 Pry Bar 1
D 1P-1861 Retaining Ring Pliers 1
E 127-9304 Spanner Wrench 1
G 1P-0510 Driver Gp 1
H 1U-6405 Three Jaw Puller 1
J 9U-6265 Pliers 1
K
156-7100 Slide Hammer Puller Gp 1
4C-5648 Threaded Adapter Gp 1
1/10(W)w

1. Use Tooling (A) in order to remove brake drum (1).
2. Remove bolts (2) and housing (3).
3. Use Tooling (B) in order to remove retaining rings (4).
4. Remove gear assemblies (5) and thrust washer (6).
2/10(W)w

5. Remove retaining rings (7), shims (8), and bearing (9) from gear (10).
6. Remove gear (11) and coupling (12).
7. Use Tooling (D) in order to remove retaining ring (13) from coupling (12).
3/10(W)w

8. Remove axle (14).
9. Remove bolts (15) and retainer (16).
10. Use Tooling (E) in order to remove nut (17).
11. Remove gear (18).
4/10(W)w

12. Remove O-ring seal (21).
13. Use Tooling (F) and Tooling (G) in order to remove bearing cone (19), spacer (22), and hub
assembly (20).
14. Remove bearing cup (23).
5/10(W)w

15. Use Tooling (C) in order to remove seal (24).
16. Remove bearing cone (25).
17. Remove bearing cup (26).
18. Use Tooling (G) and Tooling (H) in order to remove dust shield (27).
6/10(W)w

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Use Tooling (J) in order to remove spring (28).
20. Loosen bolts (29).
7/10(W)w

21. Remove bolts (30) and brake assembly (31).
22. Remove bolts (32) and bolts (29) from brake assembly (31).
23. Remove wheel cylinder (35) and brake shoes (34).
8/10(W)w

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

24. Remove retainer (36).
25. Use Tooling (K) in order to remove pins (37) from flange (38).
26. Attach a suitable lifting device to spindle (40).
27. Remove bolts (39) and spindle (40).
9/10(W)w

Shutdown SIS
Previous Screen
i06216406
Final Drive Carriers, Hubs and Brakes - Assemble - Rear
Axle
SMCS - 4054-016; 4092-016; 4253-016; 4255-016
Assembly Procedure
Table 1
Required Tools
C
1P-1859 Retaining Ring Pliers 1
1P-1853 Retaining Ring Pliers 1
1U-8758 Retaining Ring Pliers 1
E
6V-6080 Torque Multiplier Gp 1
4C-4661 Center Ring 1
4C-4058 Spanner 1
H 1P-0510 Driver Gp 1
I 9S-7354 Torque Wrench Gp 1
J 9U-5006 Torque Wrench Gp 1
K 123-6707 Seal Installer 1
L 6V-7030 Micrometer Depth Gauge Group 1
M 8T-0447 Dial Caliper 1
N 188-7400 Piston Installer 1
1/24(W)w

P 123-6695 Driver 1
Q 4C-3085 Two Jaw Puller 1
R 182-1744 Bearing Puller 1
S 6V-6640 Sealant 1
T 5P-0960 Molybdenum Grease 1
U 9S-3263 Thread Lock Compound 1
V 129-1063 Rivet Tool 1
1. Install the O-ring seals on connector (40) . Install connector (40) in the spindle.
2. Install breather valve (42) in the spindle.
3. Install O-ring seal (41) in the spindle.
Note: Some spindle assemblies will have four plugs. If the plugs have been removed, use
Tooling (V) to install four new plugs in each spindle assembly.
2/24(W)w

Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (bdy02001 and up)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (bdy02001 and up)

Similar to Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (bdy02001 and up) (20)

More from udjfjkskekmdm

More from udjfjkskekmdm (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (bdy02001 and up)