This document is a service manual for the TD95D HC tractor. It provides an introduction and table of contents for the manual, which covers topics such as the engine, clutch, transmission, four-wheel drive system, front and rear axles, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, and the platform, cab, bodywork, and decals. The introduction provides general instructions for maintenance and repair work, notes on spare parts and equipment, and notices for using the manual.

1. SERVICE MANUAL
TD95D HC
Tractor
Part number 48013264
English
August 2016
© 2016 CNHI International. All Rights Reserved.
TD95D HC
Tractor
SERVICE
MANUAL
1/1
Part number 48013264

2. Link Product / Engine
Product Market Product Engine
TD95D HC Latin America 8045.45.747
TD95D HC Australia New Zealand 8045.45.747
TD95D HC Asia Pacific 8045.45.747
TD95D HC Middle East Africa 8045.45.747
TD95D HC Europe 8045.45.747
48013264 19/11/2016

3. Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
Clutch ....................................................................................... 18
[18.110] Clutch and components ............................................................ 18.1
Transmission.............................................................................. 21
[21.114] Mechanical transmission ........................................................... 21.1
[21.140] Mechanical transmission internal components..................................... 21.2
[21.120] Gearbox ............................................................................ 21.3
[21.160] Creeper ............................................................................ 21.4
[21.162] Reverser ........................................................................... 21.5
Four-Wheel Drive (4WD) system .................................................. 23
[23.304] Four-Wheel Drive (4WD) gearbox ................................................. 23.1
Front axle system ....................................................................... 25
[25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.124] Final drive hub, steering knuckles, and shafts ..................................... 27.3
Power Take-Off (PTO)................................................................. 31
[31.101] Rear mechanical control ........................................................... 31.1
Brakes and controls .................................................................... 33
[33.AAA] Brakes and controls generic sub-group ........................................... 33.1
[33.202] Hydraulic service brakes ........................................................... 33.2
48013264 19/11/2016

4. [33.110] Parking brake or parking lock ...................................................... 33.3
[33.220] Trailer brake hydraulic control...................................................... 33.4
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.350] Safety and main relief valves ...................................................... 35.2
[35.525] Auxiliary hydraulic valves and lines ................................................ 35.3
Steering..................................................................................... 41
[41.200] Hydraulic control components...................................................... 41.1
[41.206] Pump ............................................................................... 41.2
[41.216] Cylinders ........................................................................... 41.3
Wheels...................................................................................... 44
[44.511] Front wheels........................................................................ 44.1
Cab climate control ..................................................................... 50
[50.100] Heating ............................................................................. 50.1
[50.200] Air conditioning..................................................................... 50.2
Electrical systems....................................................................... 55
[55.000] Electrical system ................................................................... 55.1
[55.100] Harnesses and connectors......................................................... 55.2
[55.201] Engine starting system ............................................................. 55.3
[55.301] Alternator........................................................................... 55.4
[55.302] Battery.............................................................................. 55.5
[55.512] Cab controls........................................................................ 55.6
[55.518] Wiper and washer system.......................................................... 55.7
[55.408] Warning indicators, alarms, and instruments ...................................... 55.8
Platform, cab, bodywork, and decals............................................. 90
[90.150] Cab................................................................................. 90.1
[90.154] Cab doors and hatches ............................................................ 90.2
48013264 19/11/2016

5. INTRODUCTION
48013264 19/11/2016
1

6. Contents
INTRODUCTION
Note to the Owner .............................................................................. 3
Safety rules ..................................................................................... 5
Safety rules ..................................................................................... 8
Consumables ................................................................................... 9
48013264 19/11/2016
2

7. INTRODUCTION
Note to the Owner
General instructions
Important notice
All maintenance and repair operations described in this manual should be carried out exclusively by the NEW HOL-
LAND authorised workshops. All instructions detailed should be carefully observed and special equipment indicated
should be used if necessary.
Everyone who carries out service operations described without carefully observing these prescriptions will be directly
responsible of deriving damages.
Shimming
At each adjustment, select adjusting shims, measure them individually using a micrometer and then sum up recorded
values. Do not rely on measuring the whole shimming set, which may be incorrect, or on rated value indicated for
each shim.
Rotating shaft seals
To correctly install rotating shaft seals, observe the following instructions:
• Let the seal soak into the same oil as it will seal for at least half an hour before mounting.
• Thoroughly clean the shaft and ensure that the shaft working surface is not damaged.
• Place the sealing lip towards the fluid. In case of a hydrodynamic lip, consider the shaft rotation direction and orient
grooves in order that they deviate the fluid towards the inner side of the seal.
• Coat the sealing lip with a thin layer of lubricant (oil rather than grease) and fill with grease the gap between the
sealing lip and the dust lip of double lip seals.
• Insert the seal into its seat and press it down using a flat punch. Do no tap the seal with a hammer or a drift.
• Take care to insert the seal perpendicularly to its seat while you are pressing it. Once the seal is settled, ensure
that it contacts the thrust element if required.
• To prevent damaging the sealing lip against the shaft, place a suitable protection during installation.
O-rings
Lubricate the O-rings before inserting them into their seats. This will prevent the O-rings from rolling over and twine
during mounting which will jeopardise sealing.
Sealers
Apply one of the following sealers: RTV SILMATE, RHODORSIL CAF 1, or LOCTITE® PIASTIC GASKET over the mating
surfaces marked with an X.
Before applying the sealer, prepare the surface as follows:
• Remove possible scales using a metal brush.
• Thoroughly degrease the surfaces using one of the following cleaning agent: trichlorethylene, petrol or a water and
soda solution.
Bearings
It is advisable to heat the bearings to 80 - 90 °C (176 - 194 °F) before mounting them on their shafts and cool them
down before inserting them into their seats with external tapping.
Roll pins
When fitting straight roll pins, ensure that the pin notch is oriented in the direction of the effort to stress the pin. Coil
roll pins can be installed in any position.
48013264 19/11/2016
3

8. INTRODUCTION
Notes for spare parts
Use exclusively genuine NEW HOLLAND spare parts.
Only genuine parts guarantee same quality, life, safety as original components as they are the same as mounted in
production.
Only the NEW HOLLAND genuine spare parts can offer this guarantee.
All spare parts orders should be complete with the following data:
• Tractor model (commercial name) and frame number.
• Engine type and number.
• Part number of the ordered part, which can be found on the “Microfiches” or the “Spare parts catalogue”, which is
the base for order processing.
Notes for equipment
Equipment which NEW HOLLAND proposes and shows in this manual are as follows:
• Studied and designed expressly for use on NEW HOLLAND tractors.
• Necessary to make a reliable repair.
• Accurately built and strictly tested to offer efficient and long-lasting working means.
We also remind the repair personnel that having these equipment means:
• Work in optimal technical conditions.
• Obtain best results.
• Save time and effort.
• Work more safely.
Notices
Wear limits indicated for some details should be intended as advised, but not binding values. The words “front”, “rear”,
“right hand”, and “left hand” referred to the different parts should be intended as seen from the operator’s seat oriented
to the normal sense of movement of the tractor.
How to move the tractor with the battery removed
Cables from the external power supply should be connected exclusively to the respective terminals of the tractor
positive and negative cables using pliers in good condition which allow proper and steady contact.
Disconnect all services (lights, wind-shield wipers, etc.) before starting the tractor
If it is necessary to check the tractor electrical system, check it only with the power supply connected. At check end,
disconnect all services and switch the power supply Off before disconnecting the cables.
48013264 19/11/2016
4

9. INTRODUCTION
Safety rules
Pay attention to this symbol
This warning symbol points out important messages involving personal safety. Carefully read the
safety rules contained herein and follow advised precautions to avoid potential hazards and safeguard
your safety and personal integrity. In this manual you will find this symbol together with the following
key-words:
WARNING – It gives warning about improper repair operations and deriving potential consequences
affecting the service technician’s personal safety.
DANGER – It gives specific warning about potential dangers for personal safety of the operator or other
persons directly or indirectly involved.
To prevent accidents
Most accidents and personal injuries taking place in workshops are due from non-observance of some simple and
essential prudential rule and safety precautions. For this reason, IN MOST CASES THEY CAN BE AVOIDED. It
suffices to foresee possible causes and act consequently with necessary caution and care.
The possibility that an accident might occur with any type of machines should not be disregarded, no matter how well
the machine in question was designed and built.
A wise and careful service technician is the best precautions against accidents.
Careful observance of this only basic precaution would be enough to avoid many severe accidents.
DANGER: Never carry out any cleaning, lubrication or maintenance operations when the engine is running.
Safety rules
Generalities
• Carefully follow specified repair and maintenance procedures.
• Do not wear rings, wristwatches, jewels, unbuttoned or flapping clothing such as ties, torn clothes, scarves, open
jackets or shirts with open zips which could get hold into moving parts. We advise to use approved safety clothing
such as anti-slipping footwear, gloves, safety goggles, helmets, etc.
• Never carry out any repair on the machine if someone is sitting on the operator’s seat, except if they are certified
operators to assist in the operation to be carried out.
• Never operate the machine or use attachments from a place other than sitting at the operator’s seat.
• Never carry out any operation on the machine when the engine is running, except when specifically indicated.
• Stop the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers, valves,
etc.
• All repair and maintenance operations should be carried out with the greatest care and attention.
• Service stairs and platforms used in a workshop or in the field should be built in compliance with the safety rules in
force.
• Disconnect the batteries and label all controls to warn that the tractor is being serviced. Block the machine and all
equipment which should be raised.
• Never check or fill fuel tanks and accumulator batteries, nor use starting liquid if you are smoking or near open
flames as such fluids are flammable.
• Brakes are inoperative when they are manually released for maintenance purposes. In such cases, the machine
should be kept constantly under control using blocks or similar devices.
• The fuel filling gun should remain always in contact with the filler neck. Maintain this contact until the fuel stops
flowing into the tank to avoid possible sparks due to static electricity buildup.
• Use exclusively specified towing points for towing the tractor. Connect parts carefully. Ensure that foreseen pins
and/or locks are steadily fixed before applying traction. Do not stop near towing bars, cables or chains working
under load.
48013264 19/11/2016
5

10. SERVICE MANUAL
Engine
TD95D HC
48013264 19/11/2016
10

11. Engine - 10
Engine and crankcase - 001
TD95D HC
48013264 19/11/2016
10.1 [10.001] / 1

12. Contents
Engine - 10
Engine and crankcase - 001
SERVICE
Engine and crankcase
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
48013264 19/11/2016
10.1 [10.001] / 2

13. Engine - Engine and crankcase
Engine and crankcase - Remove
To access the clutch it is necessary to separate the en-
gine complete with the front axle from the transmission.
ATTENTION: Lift and handle all heavy parts using suitable
lifting equipment. Make sure that assemblies or parts are
supported by means of suitable slings and hooks. Check
that no one is in the vicinity of the load to be lifted.
ATTENTION: Always use suitable tools to align holes in
parts. NEVER USE FINGERS OR HANDS.
1. Disconnect the negative battery lead.
ANIL12TR00106AA 1
2. Attach lifting chains to the bonnet (1) and attach the
chain to the hoist.
ANIL12TR00107AB 2
3. Disconnect the electrical connection (1) of bonnet.
ANIL12TR00108AB 3
48013264 19/11/2016
10.1 [10.001] / 4

14. Engine - Engine and crankcase
4. Detach the gas struts (1) from the bonnet.
ANIL12TR00109AB 4
5. Remove the four bonnet hinge bolts (1) and lift the bon-
net clear.
ANIL12TR00110AB 5
6. Disconnect the power steering hoses (1).
ANIL12TR00112AB 6
7. Disconnect the electrical connectors (1).
ANIL12TR00113AB 7
48013264 19/11/2016
10.1 [10.001] / 5

15. Engine - Engine and crankcase
8. Disconnect the delivery and return lines (1) to the power
steering cylinders.
ANIL12TR00114AB 8
9. Remove the hose (1) from the lift pump suction pipe.
ANIL12TR00115AB 9
10. Remove the hose (1) from the Power-Shuttle oil cooler
pipe.
ANIL12TR00116AB 10
11. Detach the lift pump delivery pipe (1).
ANIL12TR00117AB 11
48013264 19/11/2016
10.1 [10.001] / 6

16. Engine - Engine and crankcase
12. After draining Off the coolant into suitable containers,
unscrew the clamp (1) and remove the cab heating
system intake pipe.
ANIL12TR00118AB 12
13. Loosen the clamps (1) and remove the cab heater
outlet pipes (2). (Mark the hoses, before removal, to
facilitate refitting in the correct position).
ANIL12TR00119AB 13
14. Remove the bolts (1) and remove the footstep.
15. Remove the bolt (2) which secure the fuel tank and
lower the tank.
ANIL12TR00120AB 14
16. Loosen the clamps and remove the inlet and return
pipes (1) from the fuel tank. Remove the sender line
(2). (if necessary)
ANIL12TR00121AB 15
48013264 19/11/2016
10.1 [10.001] / 7

17. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

18. Engine - Engine and crankcase
17. Remove the front, centre and rear retaining bolts from
the front axle drive shaft guard and remove the guard.
ANIL12TR00123AA 16
18. Remove the circlip (2) from the front of the prop shaft
and slide the sleeve (1), in the direction shown by the
arrow, until it is free of the splines on the front axle.
ANIL12TR00124AB 17
19. Remove the circlip (2) from the rear of the prop shaft
and slide the sleeve (1), in the direction shown by the
arrow, until it is free of the splines on the crankshaft.
ANIL12TR00125AB 18
20. Remove the middle support bolts (1) from the pro-
peller shaft and remove the shaft complete with sup-
port.
ANIL12TR00126AB 19
48013264 19/11/2016
10.1 [10.001] / 8