1. The document provides instructions for removing and installing a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. The removal process includes disconnecting wiring, removing mounting bolts, and taking off components like the muffler, intake manifold, and cylinder head.
3. The installation process is the reverse, requiring cleaning surfaces, installing in the proper order, and torquing fasteners to specifications.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Why Is Your BMW X3 Hood Not Responding To Release Commands
John deere x115 r riding lawn tractor service repair technical manual (tm113419)
1. TM113419 - X115R, X135R, X155R, 92H, 107H Tractors
Remove Engine Single Cylinder (SN 058001-)
Remove Engine Single Cylinder (SN 058001-)
1. Turn all switches OFF. Disconnect battery negative (—) cable.
2. Lock park brake to relieve tension on traction drive belt.
3. Raise hood. Disconnect light harness on right side of hood. Lower hood to approximately 3/4 open. Slide the hood off
the bracket.
4. Remove mower deck. See Attachments section.
5.
GXT002032-UN: Engine Sheave Assembly
LEGEND:
A - Sheave Assembly
B - Cap Screw
C - Puller
Loosen sheave cap screw (B) until threads no longer engage in engine output shaft, Remove sheave assembly (A)
with a suitable puller (C), while simultaneously removing drive belt from around engine sheave.
6.
7. Remove muffler. (See Remove and Install Muffler Single Cylinder (SN 058001-).)
页码,1/4(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b559.html
2. 8.
GXT002024-UN: Engine and Main Wiring Harness Connectors
LEGEND:
D - Harness Connectors
E - Stator Wire
Disconnect engine wiring harness connectors from main wiring harness (D).
9. Disconnect stator wire (E).
10.
CAUTION:
Avoid Injury! Gasoline is flammable. Do not smoke. Always work in a ventilated area away from
open flame or spark producing equipment; including equipment that utilizes pilot lights.
页码,2/4(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b559.html
3. GXT002025-UN: Throttle Cable and Fuel Hoses
LEGEND:
F - Throttle Cable Clamp
G - Throttle Cable
H - Hose Clamp
I - Main Fuel Hose
Loosen clamp (F) and remove throttle cable (G).
11. Remove hose clamp (H) and remove fuel hose (I).
12.
GXT002026-UN: Engine Mounting Bolts
页码,3/4(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b559.html
4. LEGEND:
J - Engine Mounting Cap Screws
Remove the four engine mounting cap screws (J) securing engine to frame.
13. Remove engine from machine.
MX52301,0000D3A-19-20151112
页码,4/4(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b559.html
5. TM113419 - X115R, X135R, X155R, 92H, 107H Tractors
Install Engine Single Cylinder (SN 058001-)
Install Engine Single Cylinder (SN 058001-)
1.
CAUTION:
Avoid Injury! Gasoline is flammable. Do not smoke. Always work in a ventilated area away from
open flame or spark producing equipment; including equipment that utilizes pilot lights.
GXT002028-UN: Engine Mounting Cap Screws
LEGEND:
A - Engine Mounting Cap Screws
Place engine onto machine frame and install four engine mounting cap screws (A).
2. Tighten engine mounting bolts to specification.
Item Measurement Specification
Engine Mounting Bolts Torque 50 N·m
(37 lb.-ft.)
页码,1/4(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b6e9.html
6. 3.
GXT002029-UN: Throttle Cable
LEGEND:
B - Main Fuel Hose
C - Hose Clamp
D - Throttle Cable
E - Clamp
Install fuel hose (B) onto fuel pump and secure with hose clamp (C).
4. Install throttle cable (D) and tighten clamp (E).
5.
GXT002030-UN: Engine Electrical
页码,2/4(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b6e9.html
7. LEGEND:
F - Starter terminal
G - Engine Connectors
Connect wires to starter terminals (F).
6. Connect main wiring harness connectors (G) to engine connectors.
7.
GXT002033-UN: Sheave Installation
LEGEND:
H - Sheave Assembly
I - Cap Screw
J - Drive Belt
Install sheave assembly (H) and drive belt (J).
8. Secure sheave assembly with cap screw (I) and tighten to specification.
9. Install muffler. (See Remove and Install Muffler Single Cylinder (SN 058001-).)
10. Connect battery.
11. Install hood. (See Install Hood .)
12. Install mower deck. See Attachments section.
Item Measurement Specification
Sheave Assembly Cap Screw Torque 75 N·m
(55 lb.-ft.)
页码,3/4(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b6e9.html
8. TM113419 - X115R, X135R, X155R, 92H, 107H Tractors
Remove and Install Muffler Single Cylinder (SN 058001-)
Remove and Install Muffler Single Cylinder (SN 058001-)
Muffler Removal
1. Remove hood. (See Remove Hood )
2.
GXT002023-UN: Muffler Shield
LEGEND:
A - Pivot Bracket Cap Screws
B - Muffler Shield Cap Screws
C - Pivot Bracket
D - Muffler Shield
E - Muffler Flange Screws
F - Muffler Support Screw
G - Muffler
Remove four cap screws (A) securing hood pivot bracket (C) to machine. Remove bracket.
3. Remove four cap screws (B) securing muffler shield (D) to machine. Remove shield.
4. Remove the two muffler flange screws (E) securing the muffler (G) to the engine.
5. Remove muffler support screw (F), gasket, and muffler (G)..
Muffler Installation
页码,1/2(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b6ea.html
9. 1. Clean gasket mating surfaces of old gasket material.
2. Install new gasket.
3. Install muffler (G) onto engine with muffler flange (E) and support (F) screws.
4. Tighten to specification.
5. Install muffler shield (D) to machine using four cap screws (B).
6. Install hood pivot bracket (C) using four cap screws (A).
7. Install hood. (See Install Hood )
Item Measurement Specification
Muffler Screws Torque 16 N·m
(140 lb.-in.)
MX52301,0000D3C-19-20151112
页码,2/2(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa82f5b6ea.html
10. TM113419 - X115R, X135R, X155R, 92H, 107H Tractors
Remove Cylinder Head Single Cylinder
Remove Cylinder Head Single Cylinder
MXT003030-UN: Valve Cover Cap Screws
LEGEND:
A - Cap Screws
1. Disconnect spark plug lead and remove spark plug.
2. Remove air cleaner assembly, carburetor and blower housing.
3. Remove intake manifold and governor control bracket and linkage.
4. Remove valve cover cap screws (A).
5. NOTE:
Mark the push rods for reassembly in their original position. The exhaust valve push rod is steel and is marked with a red stripe. The intake valve push rod is aluminum.
MXT003031-UN: Rocker Arms and Push Rods
LEGEND:
B - Adjustment Nuts
C - Rocker Arms
D - Pivots
E - Push Rods
Remove rocker arm adjustment nuts (B), rocker arms (C), rocker arm pivots (D), and push rods (E).
页码,1/3(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa829c81b4.html
11. 6.
MXT016301-UN: Cylinder Head Bolts
Remove cylinder head bolts in sequence shown.
页码,2/3(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa829c81b4.html
12. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
13. 7.
MXT003033-UN: Cylinder Head and Gasket
Remove cylinder head, cylinder head gasket and push rods. Discard the gasket.
OUO2003,0000094-19-20151130
页码,3/3(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa829c81b4.html
14. TM113419 - X115R, X135R, X155R, 92H, 107H Tractors
Install Cylinder Head Single Cylinder
Install Cylinder Head Single Cylinder
MXT003034-UN: Cylinder Head and Gasket
LEGEND:
A - Alignment Sleeves
1. Clean gasket surfaces.
2. IMPORTANT:
Do not use sealer of any kind on gaskets.
Place new gasket and cylinder head on cylinder. Align head with alignment sleeves (A) located in the cylinder.
3. Apply thin coat of clean engine oil to threads. Install eight cylinder heads bolts.
4. IMPORTANT:
Do not tighten each bolt to final torque in a single step. Incorrect tightening may cause a warped cylinder head. Step-tighten all bolts to 1/3 of the final torque value, then 2/3
of the final torque value.
页码,1/3(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa829c81b5.html
15. MXT016301-UN: Cylinder Head Bolts
Tighten all bolts down evenly by hand. Tighten cylinder head bolts in sequence shown in three even increments to specification.
5. IMPORTANT:
The exhaust valve push rod is steel and is marked with a red stripe. The intake valve push rod is aluminum.
Item Measurement Specification
Cylinder Head Bolts Torque 28.2 N·m
(250 lb·in)
页码,2/3(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa829c81b5.html
16. MXT003036-UN: Rocker Arms and Push Rods
LEGEND:
B - Nuts
C - Rocker Arms
D - Pivots
E - Push Rods
Install push rods (E), rocker arm pivots (D), rocker arms (C), and arm support nuts (B). Tighten to specification.
6. Adjust valve clearance. (See Valve Clearance Adjustment Single Cylinder .)
7.
GXT001593-UN: Valve Cover Torque Sequence
Install valve cover with new gasket. Tighten to specification using the sequence shown.
8. Install intake manifold. Tighten bolts to specification.
9. Install blower housing.
10. Install governor control bracket and linkage.
11. Install carburetor and adjust governor linkage. (See Install Carburetor Single Cylinder and Governor Static Adjustment .)
12. Install air cleaner assembly.
13. Install spark plug and plug wire.
Item Measurement Specification
Valve Cover Screws Torque 8 N·m
(70 lb·in)
Item Measurement Specification
Intake Manifold Bolts Torque 10 N·m
(90 lb·in)
OUO2003,0000095-19-20151130
页码,3/3(W)w
11/26/2019file://C:ProgramDataService ADVISORTempTM113419_09001faa829c81b5.html