The brakes are not engaging or holding the machine. Check the park brake lock lever for wear or damage. If not damaged, check the brake linkage adjustment and condition of the brake return springs. The brakes consist of plates and disks inside the axle housing that are activated by depressing the brake pedal, which is connected to linkage in each axle shaft housing. Rotating brake cams apply pressure to friction disks when the pedal is depressed.
This document provides information about personal protective equipment (PPE) requirements. It discusses that employers must provide PPE to employees when hazards are present that could cause injury. The document outlines employer responsibilities to assess hazards, select appropriate PPE, provide training to employees, and maintain equipment. It then focuses on eye and face protection, describing common hazards, types of protective equipment like safety glasses and goggles, and proper use and fit. The goal is to educate about protecting eyes from workplace dangers.
Este documento presenta una guía para el desarrollo de procedimientos seguros para tareas de alto riesgo que involucran el manejo de energías peligrosas. Explica la necesidad de tales procedimientos para evitar accidentes y describe el método recomendado, que incluye realizar un inventario de tareas con energías peligrosas, establecer una política de seguridad, y desarrollar procedimientos específicos que cubran aspectos como el aislamiento, bloqueo y verificación de equipos. El objetivo final es entregar una
This document provides resources for applying for a release manager position, including two sample cover letters, tips for writing an effective cover letter, resume samples, and interview preparation materials such as common interview questions, thank you letter samples, and interview dos and don'ts.
Experience Certificate Concierge Supervisor at Red Sea Hotels Group.PDFHassan Samir
Mr. Hassan Samir Hassan Sharaf worked as a Concierge Supervisor and Services Department employee at the Palace Port Ohalib hotel in Marsa Alam, Egypt from February 1, 2015 to June 2, 2016. The hotel issued him a certificate of experience at his request, noting his good performance, reliability, and quality of service provided during his time there, and wishing him good luck in future endeavors.
This document provides information about personal protective equipment (PPE) requirements. It discusses that employers must provide PPE to employees when hazards are present that could cause injury. The document outlines employer responsibilities to assess hazards, select appropriate PPE, provide training to employees, and maintain equipment. It then focuses on eye and face protection, describing common hazards, types of protective equipment like safety glasses and goggles, and proper use and fit. The goal is to educate about protecting eyes from workplace dangers.
Este documento presenta una guía para el desarrollo de procedimientos seguros para tareas de alto riesgo que involucran el manejo de energías peligrosas. Explica la necesidad de tales procedimientos para evitar accidentes y describe el método recomendado, que incluye realizar un inventario de tareas con energías peligrosas, establecer una política de seguridad, y desarrollar procedimientos específicos que cubran aspectos como el aislamiento, bloqueo y verificación de equipos. El objetivo final es entregar una
This document provides resources for applying for a release manager position, including two sample cover letters, tips for writing an effective cover letter, resume samples, and interview preparation materials such as common interview questions, thank you letter samples, and interview dos and don'ts.
Experience Certificate Concierge Supervisor at Red Sea Hotels Group.PDFHassan Samir
Mr. Hassan Samir Hassan Sharaf worked as a Concierge Supervisor and Services Department employee at the Palace Port Ohalib hotel in Marsa Alam, Egypt from February 1, 2015 to June 2, 2016. The hotel issued him a certificate of experience at his request, noting his good performance, reliability, and quality of service provided during his time there, and wishing him good luck in future endeavors.
This document provides three certificates of employment for Muhammad Aamir Shahzad. The certificates are from M/S.Descon Engineering LLC in Qatar, Technip in Abu Dhabi, and Descon Engineering in Abu Dhabi, certifying that Mr. Shahzad worked as an electrical inspector and QC inspector from 2012 to 2010. The certificates praise his job performance and contributions to various projects.
The document is a scanned receipt from a restaurant showing a total of $56.92 was spent. It lists items purchased including drinks, appetizers, entrees and dessert. The receipt details the date, time, payment method and includes a thank you message from the restaurant.
This letter certifies that Hafiz Danial Baig worked as a trainee assistant accountant from April 2016 to July 2016 and was then appointed as an assistant accountant in the finance department. The letter praises Hafiz as well-mannered, punctual, and industrious. It wishes him success in future endeavors.
Biodegradable bamboo cutlery is made from bamboo unlike plastic materials. These kitchen utensils are the most important things since most of work is done by them. Basically it includes knife, fork and spoon. These kitchen products play a very significant role in our kitchen life. You would be using these products in your day to day activities while eating your food. NinoBamboo comes into picture where you can buy bamboo cutlery at a very reasonable price.
This letter serves as a reference for Asim Iqbal, recommending him for his work as a Mechanical Inspector and Supervising Mechanical Engineer on water reservoir projects in Saudi Arabia. Asim worked on these strategic water development projects from 2012 to 2015, supervising the installation of mechanical items like pipes, valves, and pumps. The letter confirms that Asim proved himself a valuable member of the project team, diligently checking mechanical works and assisting management. He is recommended for his efforts and competence in mechanical engineering aspects of construction.
Mr. Muhammad Zubair Noor worked as a QA/QC Engineer for Engin (Pvt) Ltd from March 16, 2014 to present on two construction projects for the Pakistan Atomic Energy Commission: 1) Construction of SR, RS & EM Building for C-3/C-4 in Chashma, and 2) Construction of Internal Roads, Foot Paths, Fencing, and Covered Walkways for C-3/C-4 in Chashma. The project manager found him to be efficient, hard working, and dedicated, able to work in tough conditions and independently according to technical specifications.
El documento trata sobre seguridad industrial. Explica las actividades de planeación, organización, ejecución y evaluación para preservar la salud de los trabajadores. También cubre el marco legal, actividades de higiene industrial, seguridad, medicina preventiva, elementos de protección personal, prevención de accidentes, inspecciones, investigaciones y programas de orden y aseo para garantizar la seguridad en el trabajo.
La Unión Europea ha propuesto un nuevo paquete de sanciones contra Rusia que incluye un embargo al petróleo. El embargo se aplicaría gradualmente durante seis meses para el petróleo crudo y ocho meses para los productos refinados. Este paquete de sanciones requiere la aprobación unánime de los 27 estados miembros de la UE.
Top 8 easyjet pilot interview questions answersPilotCareer88
The document provides sample answers to common interview questions for Easyjet pilots. It discusses 8 questions: 1) importance of language skills, 2) responsibilities as a pilot, 3) behavior during emergencies, 4) modifying flight courses, 5) career goals, 6) strengths, 7) knowledge of the organization, and 8) improving pilot knowledge. For each question, it offers tips on effective answers and examples that emphasize skills like multitasking, problem-solving, safety procedures, and continuous learning. The goal is to demonstrate one's qualifications and suitability as an Easyjet pilot through well-prepared responses.
John deere 4710 compact utility tractor service repair manualfjkskmmdmme
This technical manual provides instructions and safety information for servicing Compact Utility Tractors models 4510, 4610, and 4710. It contains sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, repair, and other relevant topics. Safety is the top priority in working on these machines, and specific precautions are outlined to prevent injury from electrical, mechanical, chemical, and other hazards.
John deere 4510 compact utility tractor service repair manualfjkskmmdmme
This document provides specifications and general information related to diesel fuel and engine oil for John Deere compact utility tractors models 4510, 4610, and 4710. It specifies the recommended diesel fuel grades and properties, including cetane number, cold filter plugging point, and sulfur content. It also provides guidelines for proper diesel fuel storage and notes potential fuel contaminants. The document recommends specific John Deere engine oil brands and viscosities matched to expected operating temperature ranges. It indicates other oil brands may be used if they meet API performance standards.
This document provides three certificates of employment for Muhammad Aamir Shahzad. The certificates are from M/S.Descon Engineering LLC in Qatar, Technip in Abu Dhabi, and Descon Engineering in Abu Dhabi, certifying that Mr. Shahzad worked as an electrical inspector and QC inspector from 2012 to 2010. The certificates praise his job performance and contributions to various projects.
The document is a scanned receipt from a restaurant showing a total of $56.92 was spent. It lists items purchased including drinks, appetizers, entrees and dessert. The receipt details the date, time, payment method and includes a thank you message from the restaurant.
This letter certifies that Hafiz Danial Baig worked as a trainee assistant accountant from April 2016 to July 2016 and was then appointed as an assistant accountant in the finance department. The letter praises Hafiz as well-mannered, punctual, and industrious. It wishes him success in future endeavors.
Biodegradable bamboo cutlery is made from bamboo unlike plastic materials. These kitchen utensils are the most important things since most of work is done by them. Basically it includes knife, fork and spoon. These kitchen products play a very significant role in our kitchen life. You would be using these products in your day to day activities while eating your food. NinoBamboo comes into picture where you can buy bamboo cutlery at a very reasonable price.
This letter serves as a reference for Asim Iqbal, recommending him for his work as a Mechanical Inspector and Supervising Mechanical Engineer on water reservoir projects in Saudi Arabia. Asim worked on these strategic water development projects from 2012 to 2015, supervising the installation of mechanical items like pipes, valves, and pumps. The letter confirms that Asim proved himself a valuable member of the project team, diligently checking mechanical works and assisting management. He is recommended for his efforts and competence in mechanical engineering aspects of construction.
Mr. Muhammad Zubair Noor worked as a QA/QC Engineer for Engin (Pvt) Ltd from March 16, 2014 to present on two construction projects for the Pakistan Atomic Energy Commission: 1) Construction of SR, RS & EM Building for C-3/C-4 in Chashma, and 2) Construction of Internal Roads, Foot Paths, Fencing, and Covered Walkways for C-3/C-4 in Chashma. The project manager found him to be efficient, hard working, and dedicated, able to work in tough conditions and independently according to technical specifications.
El documento trata sobre seguridad industrial. Explica las actividades de planeación, organización, ejecución y evaluación para preservar la salud de los trabajadores. También cubre el marco legal, actividades de higiene industrial, seguridad, medicina preventiva, elementos de protección personal, prevención de accidentes, inspecciones, investigaciones y programas de orden y aseo para garantizar la seguridad en el trabajo.
La Unión Europea ha propuesto un nuevo paquete de sanciones contra Rusia que incluye un embargo al petróleo. El embargo se aplicaría gradualmente durante seis meses para el petróleo crudo y ocho meses para los productos refinados. Este paquete de sanciones requiere la aprobación unánime de los 27 estados miembros de la UE.
Top 8 easyjet pilot interview questions answersPilotCareer88
The document provides sample answers to common interview questions for Easyjet pilots. It discusses 8 questions: 1) importance of language skills, 2) responsibilities as a pilot, 3) behavior during emergencies, 4) modifying flight courses, 5) career goals, 6) strengths, 7) knowledge of the organization, and 8) improving pilot knowledge. For each question, it offers tips on effective answers and examples that emphasize skills like multitasking, problem-solving, safety procedures, and continuous learning. The goal is to demonstrate one's qualifications and suitability as an Easyjet pilot through well-prepared responses.
John deere 4710 compact utility tractor service repair manualfjkskmmdmme
This technical manual provides instructions and safety information for servicing Compact Utility Tractors models 4510, 4610, and 4710. It contains sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, repair, and other relevant topics. Safety is the top priority in working on these machines, and specific precautions are outlined to prevent injury from electrical, mechanical, chemical, and other hazards.
John deere 4510 compact utility tractor service repair manualfjkskmmdmme
This document provides specifications and general information related to diesel fuel and engine oil for John Deere compact utility tractors models 4510, 4610, and 4710. It specifies the recommended diesel fuel grades and properties, including cetane number, cold filter plugging point, and sulfur content. It also provides guidelines for proper diesel fuel storage and notes potential fuel contaminants. The document recommends specific John Deere engine oil brands and viscosities matched to expected operating temperature ranges. It indicates other oil brands may be used if they meet API performance standards.
John deere 4610 compact utility tractor service repair manualfjkskmmdmme
This document provides specifications and general information related to diesel fuel and engine oil for John Deere compact utility tractors models 4510, 4610, and 4710. It specifies the recommended diesel fuel grades and properties, including cetane number, cold filter plugging point, and sulfur content. It also provides guidelines for proper diesel fuel storage and notes potential fuel contaminants. The document recommends specific John Deere engine oil brands and viscosities matched to expected operating temperature ranges. It indicates other oil brands may be used if they meet API performance standards.
John deere 1435 front mower service repair manualdidkkmmdm
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1420 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1420 front mower service repair manualdidkkmmdm
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1445 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides instructions to check each component and make any necessary repairs or adjustments.
John deere 1565 front mower service repair manualdidkkmmdm
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1565 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1545 front mower service repair manualfjsjekkdmnem
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1565 front mower service repair manualfjsjekkdmnem
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1435 front mower service repair manualfjsjekkdmnem
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1445 front mower service repair manualfjsjekkdmnem
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1445 front mower service repair manualdidkkmmdm
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1420 front mower service repair manualfjsjekkdmnem
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1545 front mower service repair manualdidkkmmdm
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1545 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1435 front mower service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere ts and th 6x4 gator utility vehicle service repair manualfujskekfmsme
The document is a technical manual for John Deere Gator utility vehicles. It provides an overview of the manual's organization and contents. The manual is divided into specific sections covering topics like specifications, component locations, theory of operation, diagnostics, repair procedures, and safety information. It notes that the manual is intended for experienced technicians and contains all necessary information for working on particular vehicle systems.
John deere 790 compact utility tractor service repair manualfjjskekdmme
The diesel engine uses a mechanical fuel transfer pump to draw fuel from the tank and supply it to the fuel filter. The injection pump then sends the filtered fuel at high pressure to the injectors. Excess fuel and fuel leaked past the injectors is returned to the tank. Air is drawn into the air cleaner through an inlet hose and is filtered before entering the intake manifold. The injection pump meters and times the delivery of fuel to the injectors based on engine speed and load.
Similar to John deere 1420 front mower service repair manual (20)
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 330 l excavator (prefix 5ym) service repair manual (5ym00001 ...fjsjekdmmeme
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 b ln excavator (prefix 5lr) service repair manual (5lr000...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the component locations and assembly sequences.
Caterpillar cat 330 b ln excavator (prefix 3yr) service repair manual (3yr000...fjsjekdmmeme
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fjsjekdmmeme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjsjekdmmeme
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, bolts, and using a lifting device due to the head's weight of 95 kg.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjsjekdmmeme
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
Caterpillar cat 315 c excavator (prefix cfl) service repair manual (cfl00001 ...fjsjekdmmeme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) It details 21 steps for disassembly, including removing gears, shafts, seals, and housing components.
3) The 19 steps for assembly describe installing these same parts in reverse order, with notes on cleaning, lubricating, and using various tools to set proper torque and clearance.
Caterpillar cat 311 c u excavator (prefix pad) service repair manual (pad0000...fjsjekdmmeme
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 311 c u excavator (prefix cke) service repair manual (cke0000...fjsjekdmmeme
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new seals. It also includes instructions for removing and installing the engine oil filter base and engine oil cooler.
Caterpillar cat 311 c excavator (prefix pad) service repair manual (pad00001 ...fjsjekdmmeme
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjsjekdmmeme
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new seals. It also includes instructions for removing and installing the engine oil filter base and engine oil cooler.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjsjekdmmeme
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate
2. Camshaft
3. Camshaft bearings
4. Connecting rod bearings
5. Crankshaft main bearings
The instructions describe each removal and installation step in detail and include notes about proper procedure, tool usage, torque specifications and checks to perform.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
1. TM1806 NOVEMBER 2002
JOHN DEERE
WORLDWIDE COMMERCIAL & CONSUMER
EQUIPMENT DIVISION
1806
November 2002
Front Mowers
1420, 1435, 1445, 1545 and 1565
TECHNICAL MANUAL
North American Version
Litho in U.S.A.
3. Safety - 1
SAFETY
Safety
Recognize Safety Information
MIF
This is the safety-alert symbol. When you see this symbol
on your machine or in this manual, be alert to the potential
for personal injury.
Follow recommended precautions and safe servicing
practices.
Understand Signal Words
A signal word - DANGER, WARNING, or CAUTIon - is used
with the safety-alert symbol. DANGER identifies the most
serious hazards.
DANGER or WARNING safety signs are located near
specific hazards. General precautions are listed on
CAUTIon safety signs. CAUTIon also calls attention to
safety messages in this manual.
Replace Safety Signs
MIF
Replace missing or damaged safety signs. See the
machine operator’s manual for correct safety sign
placement.
Handle Fluids Safely - Avoid Fires
Be Prepared For Emergencies
MIF
• When you work around fuel, do not smoke or work near
heaters or other fire hazards.
• Store flammable fluids away from fire hazards. Do not
incinerate or puncture pressurized containers.
• Make sure machine is clean of trash, grease, and
debris.
• Do not store oily rags; they can ignite and burn
spontaneously.
• Be prepared if a fire starts.
• Keep a first aid kit and fire extinguisher handy.
• Keep emergency numbers for doctors, ambulance
service, hospital, and fire department near your telephone.
Use Care In Handling and Servicing Batteries
MIF
4. Safety - 2
SAFETY
Prevent Battery Explosions
• Keep sparks, lighted matches, and open flame away
from the top of battery. Battery gas can explode.
• Never check battery charge by placing a metal object
across the posts. Use a volt-meter or hydrometer.
• Do not charge a frozen battery; it may explode. Warm
battery to 16°C (60°F).
Prevent Acid Burns
• Sulfuric acid in battery electrolyte is poisonous. It is
strong enough to burn skin, eat holes in clothing, and
cause blindness if splashed into eyes.
Avoid acid burns by:
1. Filling batteries in a well-ventilated area.
2. Wearing eye protection and rubber gloves.
3. Avoiding breathing fumes when electrolyte is added.
4. Avoiding spilling or dripping electrolyte.
5. Use proper jump start procedure.
If you spill acid on yourself:
1. Flush your skin with water.
2. Apply baking soda or lime to help neutralize the acid.
3. Flush your eyes with water for 10 - 15 minutes.
4. Get medical attention immediately.
If acid is swallowed:
1. Drink large amounts of water or milk.
2. Then drink milk of magnesia, beaten eggs, or vegetable
oil.
3. Get medical attention immediately.
Wear Protective Clothing
MIF
Wear close fitting clothing and safety equipment
appropriate to the job.
Prolonged exposure to loud noise can cause impairment or
loss of hearing. Wear a suitable hearing protective device
such as earmuffs or earplugs to protect against
objectionable or uncomfortable loud noises.
Operating equipment safely requires the full attention of the
operator. Do not wear radio or music headphones while
operating machine.
Use Care Around High-Pressure Fluid Lines
Avoid High-Pressure Fluids
MIF
Escaping fluid under pressure can penetrate the skin
causing serious injury.
Avoid injury from escaping fluid under pressure by stopping
the engine and relieving pressure in the system before
disconnecting or connecting hydraulic or other lines.
Tighten all connections before applying pressure.
Search for leaks with a piece of cardboard. Protect hands
and body from high pressure fluids.
If an accident occurs, see a doctor immediately. Any fluid
injected into the skin must be surgically removed within a
few hours or gangrene may result. Doctors unfamiliar with
this type of injury should reference a knowledgeable
medical source. Such information is available from Deere &
Company Medical Department in Moline, Illinois, U.S.A.
Avoid Heating Near Pressurized Fluid Lines
MIF
Flammable spray can be generated by heating near
pressurized fluid lines, resulting in severe burns to yourself
and bystanders. Do not heat by welding, soldering, or using
a torch near pressurized fluid lines or other flammable
materials. Pressurized lines can be accidentally cut when
heat goes beyond the immediate flame area.
5. Safety - 3
SAFETY
Service Machines Safely
MIF
Tie long hair behind your head. Do not wear a necktie,
scarf, loose clothing, or necklace when you work near
machine tools or moving parts. If these items were to get
caught, severe injury could result.
Remove rings and other jewelry to prevent electrical shorts
and entanglement in moving parts.
Use Proper Tools
Use tools appropriate to the work. Makeshift tools and
procedures can create safety hazards. Use power tools
only to loosen threaded parts and fasteners. For loosening
and tightening hardware, use the correct size tools. Do not
use U.S. measurement tools on metric fasteners. Avoid
bodily injury caused by slipping wrenches. Use only service
parts meeting John Deere specifications.
Park Machine Safely
MIF
Before working on the machine:
1. Lower all equipment to the ground.
2. Stop the engine and remove the key.
3. Disconnect the battery ground strap.
4. Hang a “Do Not Operate” tag in operator station.
Support Machine Properly and Use Proper
Lifting Equipment
MIF
If you must work on a lifted machine or attachment,
securely support the machine or attachment.
Do not support the machine on cinder blocks, hollow tiles,
or props that may crumble under continuous load. Do not
work under a machine that is supported solely by a jack.
Follow recommended procedures in this manual.
Lifting heavy components incorrectly can cause severe
injury or machine damage. Follow recommended
procedure for removal and installation of components in the
manual.
Work In Clean Area
Before starting a job:
1. Clean work area and machine.
2. Make sure you have all necessary tools to do your job.
3. Have the right parts on hand.
4. Read all instructions thoroughly; do not attempt
shortcuts.
Using High Pressure Washers
Directing pressurized water at electronic/electrical
components or connectors, bearings, hydraulic seals, fuel
injection pumps or other sensitive parts and components
may cause product malfunctions. Reduce pressure and
spray at a 45 to 90 degree angle.
Illuminate Work Area Safely
Illuminate your work area adequately but safely. Use a
portable safety light for working inside or under the
machine. Make sure the bulb is enclosed by a wire cage.
The hot filament of an accidentally broken bulb can ignite
spilled fuel or oil.
6. Safety - 4
SAFETY
Work In Ventilated Area
MIF
Engine exhaust fumes can cause sickness or death. If it is
necessary to run an engine in an enclosed area, remove
the exhaust fumes from the area with an exhaust pipe
extension.
If you do not have an exhaust pipe extension, open the
doors and get outside air into the area.
Warning: California Proposition 65 Warning
Gasoline engine exhaust from this product contains
chemicals known to the State of California to cause cancer,
birth defects, or other reproductive harm.
Diesel engine exhaust and some of its constituents are
known to the State of California to cause cancer, birth
defects, and other reproductive harm.
Remove Paint Before Welding or Heating
Avoid potentially toxic fumes and dust. Hazardous fumes
can be generated when paint is heated by welding,
soldering, or using a torch. Do all work outside or in a well
ventilated area. Dispose of paint and solvent properly.
Remove paint before welding or heating: If you sand or
grind paint, avoid breathing the dust. Wear an approved
respirator. If you use solvent or paint stripper, remove
stripper with soap and water before welding. Remove
solvent or paint stripper containers and other flammable
material from area. Allow fumes to disperse at least 15
minutes before welding or heating.
Avoid Harmful Asbestos Dust
Avoid breathing dust that may be generated when
handling components containing asbestos fibers.
Inhaled asbestos fibers may cause lung cancer.
Components in products that may contain asbestos
fibers are brake pads, brake band and lining assemblies,
clutch plates, and some gaskets. The asbestos used in
these components is usually found in a resin or sealed in
some way. Normal handling is not hazardous as long as
airborne dust containing asbestos is not
generated.
Avoid creating dust. Never use compressed air for cleaning.
Avoid brushing or grinding material containing asbestos.
When servicing, wear an approved respirator. A special
vacuum cleaner is recommended to clean asbestos. If not
available, apply a mist of oil or water on the material
containing asbestos. Keep bystanders away from the area.
Service Tires Safely
MIF
Explosive separation of a tire and rim parts can cause
serious injury or death.
Do not attempt to mount a tire unless you have the proper
equipment and experience to perform the job.
Always maintain the correct tire pressure. Do not inflate the
tires above the recommended pressure. Never weld or heat
a wheel and tire assembly. The heat can cause an increase
in air pressure resulting in a tire explosion. Welding can
structurally weaken or deform the wheel.
When inflating tires, use a clip-on chuck and extension
hose long enough to allow you to stand to one side and not
in front of or over the tire assembly. Use a safety cage if
available.
Check wheels for low pressure, cuts, bubbles, damaged
rims or missing lug bolts and nuts.
7. Safety - 5
SAFETY
Avoid Injury From Rotating Blades, Augers
and PTO Shafts
MIF
Keep hands and feet away while machine is running. Shut
off power to service, lubricate or remove mower blades,
augers or PTO shafts.
Service Cooling System Safely
MIF
Explosive release of fluids from pressurized cooling system
can cause serious burns.
Shut off machine. Only remove filler cap when cool enough
to touch with bare hands. Slowly loosen cap to first stop to
relieve pressure before removing completely.
Handle Chemical Products Safely
MIF
Direct exposure to hazardous chemicals can cause serious
injury. Potentially hazardous chemicals used with John
Deere equipment include such items as lubricants,
coolants, paints, and adhesives.
A Material Safety Data Sheet (MSDS) provides specific
details on chemical products: physical and health hazards,
safety procedures, and emergency response techniques.
Check the MSDS before you start any job using a
hazardous chemical. That way you will know exactly what
the risks are and how to do the job safely. Then follow
procedures and recommended equipment.
Dispose Of Waste Properly
Improperly disposing of waste can threaten the
environment and ecology. Potentially harmful waste used
with John Deere equipment include such items as oil, fuel,
coolant, brake fluid, filters, and batteries. Use leakproof
containers when draining fluids. Do not use food or
beverage containers that may mislead someone into
drinking from them. Do not pour waste onto the ground,
down a drain, or into any water source. Inquire on the
proper way to recycle or dispose of waste from your local
environmental or recycling center, or from your John Deere
dealer.
Live With Safety
MIF
Before returning machine to customer, make sure machine
is functioning properly, especially the safety systems. Install
all guards and shields.
8. Brakes Component Location - 684
BRAKES COMPONENT LOCATION
Component Location
Brake System Component Location
MX5550
A - Turnbuckle
B - Brake Link Assembly
C - Right Turn Brake Pedal
D - Left Turn Brake Pedal
E - Neutral Safety Arm
F - Neutral Safety Link
G - Support Bracket
H - Master Brake Pedal
I - Park Lock Assembly
J - Brake Pedal Shaft
K - Axle Shaft
L - Friction Disk (2 used)
M - Separator Plate (2 used)
N - Actuator Lever
O - Return Spring
P - Brake Pedal Shaft Bushing (2 used)
A
B
C
D
E
F
G
H
I
J
K
L
M
NO
P
9. Brakes Theory of Operation - 685
BRAKES THEORY OF OPERATION
Theory of Operation
Brake System Operation
Function:
To provide a means of stopping the machine and to prevent
the machine from moving when not in use.
Theory of Operation:
The brake system consists of plates and disks located
inside the axle housing on each side of the transaxle
assembly.
The brakes are activated by a common pedal hooked to
linkage connected to the individual brake assemblies
located in each of the axle shaft housings. The brakes may
be activated individually by depressing either the left turn
brake pedal or the right turn brake pedal.
Inside each axle shaft housing, the brake components
consist of a brake actuator lever/cam, actuator plate, and
pairs of alternating friction disks and separator plates.
The brake actuator plate is mounted on six steel balls,
which ride inside pockets with ramps on the actuator plate.
The brake friction disks are splined to the axle shafts. The
separator plates are keyed to the brake actuator lever/cam
shaft and cannot move.
When the brake pedal is depressed, the brake actuator
lever/cams rotate, forcing the brake actuator plate to rotate.
As the actuator plate rotates, the ramps on the plate will
allow the plate to ride up, forcing the plate against the
friction disks and separator plates, causing drag and
slowing the machine.
When the pedal is released, the return springs return the
brake actuator lever/cams to the rest position, allowing the
actuator plates to release the pressure on the friction disks
and separator plates.
The machine is equipped with a park brake lock. When the
brake pedal is depressed and held, and the park brake lock
lever is pulled up, a pawl engages with the teeth on the
pivot shaft, locking the brake linkage.
10. Brakes Diagnostics - 686
BRAKES DIAGNOSTICS
Diagnostics
Machine Will Not Move
NOTE: This condition may be caused by systems other than brakes. Check the power train system if the following
conditions do not correct the problem.
Brake Will Not Engage or Hold Machine
Test Conditions:
• Machine parked safely.
• Park brake released.
Check park brake lock lever assembly for wear or damage. Lever moves freely. Go To Next Step.
• Park brake lock lever assembly is worn or damaged.
Repair or replace as necessary.
Check brake linkage adjustment. (See “Adjusting Brakes:”
on page 688 in this section.)
Linkage is properly adjusted. Go To Next Step.
• Linkage needs adjustment. (See “Adjusting Brakes:” on
page 688 in this section.)
Check condition of brake return springs. Springs must not be stretched, broken, or missing.
• Springs are damaged or missing. Replace springs as
necessary.
Test Conditions:
• Machine parked safely.
Check brake linkage adjustment. (See “Adjusting Brakes:”
on page 688 in this section.)
Linkage is properly adjusted. Go To Next Step.
• Linkage needs adjustment. (See “Adjusting Brakes:” on
page 688 in this section.)
Check brake friction disks for wear or damage. Friction disks are not worn or damaged. Go To Next
Step.
• Friction disks are worn or damaged. Replace as
necessary.
Check brake separator plates for wear or damage. Separator plates must not be worn or damaged.
• Separator plates are worn or damaged. Replace as
necessary.
11. Brakes Diagnostics - 687
BRAKES DIAGNOSTICS
Excessive Brake Wear
Machine Pulls to One Side
NOTE: This condition may be caused by systems other than brakes. Check the power train system if the following
conditions do not correct the problem.
Test Conditions:
• Machine parked safely.
Check brake pedal shaft and bushings for wear or damage. Shaft moves freely. Go To Next Step.
• Shaft is worn or damaged. Repair or replace as
necessary.
Check park brake lock lever assembly for wear or damage. Lever moves freely. Go To Next Step.
• Park brake lock lever assembly is worn or damaged.
Repair or replace as necessary.
Check condition of brake return springs. Springs are not stretched, broken, or missing. Go To
Next Step.
• Springs are damaged or missing. Replace springs as
necessary.
Check brake separator plates for wear or damage. Plates must not be worn or damaged.
• Plates are worn or damaged. Replace as necessary.
Test Conditions:
• Machine parked safely.
• Park brake released.
Check brake linkage adjustment. (See “Adjusting
Brakes:” on page 688 in this section.)
Linkage is properly adjusted. Go To Next Step.
• Linkage needs adjustment. (See “Adjusting Brakes:” on
page 688 in this section.)
Check park brake lock lever assembly for wear or
damage.
Lever moves freely. Go To Next Step.
• Park brake lock lever assembly is worn or damaged.
Repair or replace as necessary.
Check condition of brake return springs. Springs are not stretched, broken, or missing. Go To Next
Step.
• Springs are damaged or missing. Replace springs as
necessary.
Check brake friction disks for wear or damage. Friction disks are not worn or damaged. Go To Next Step.
• Disks are worn or damaged. Replace as necessary.
Check brake separator plates for wear or damage. Separator plates must not be worn or damaged.
• Plates are worn or damaged. Replace as necessary.
12. Brakes Tests and Adjustments - 688
BRAKES TESTS AND ADJUSTMENTS
Tests and Adjustments
Turn Brake Adjustment
Checking Turn Brake Pedal Free Play:
1. Park machine on level ground.
2. Unlock park brake.
MX5609
3. Place a piece of tape (A) on the front surface of each
turn brake pedal and extending below the floor (C).
4. Make a mark (B) at the same height of the floor on the
tape.
MX5610
5. Press turn brake pedal until brake engages. Mark
position of floor (D) on tape.
6. Release brake pedal and measure the distance (E)
between the front edge of the marks on the tape to
determine pedal travel.
7. Repeat steps 3 - 6 for the other turn brake pedal.
8. If brake pedal travel is greater than 30 mm, the brakes
require adjustment.
Adjusting Brakes:
MX5610
1. Using tape installed earlier, make two marks (A) at 25
mm and 30 mm above the floor.
MX5611
2. Loosen lock nuts (B), and adjust turnbuckle (C) until
brake begins to engage when the pedal is between the 25
mm and 30 mm marks on the tape.
3. Repeat for other pedal, keeping left and right side
pedals adjusted evenly.
4. Tighten turnbuckle lock nuts.
5. If brakes cannot be adjusted within the range of the
turnbuckles, check the transaxle brake plates and disks.
B
A
C
D
E
A
B
C
13. Brakes Tests and Adjustments - 689
BRAKES TESTS AND ADJUSTMENTS
Brake Switch Adjustment
Inspection:
1. Park machine on level surface.
2. Unlock park brake.
3. Disconnect battery negative (-) cable.
4. Open service hatch.
5. Inspect brake switch. If boot, plunger and brake switch
are worn or damaged, replace brake switch.
MX5622
6. Depress master brake pedal. Plunger on brake switch
(A) should extend when mixer (B) and neutral safety arm
(C) are activated.
7. Release master brake pedal. Plunger on brake switch
should retract completely when neutral safety arm is
activated by neutral safety link (D) and ball joint (E).
Adjustment:
MX5623
1. Loosen lock nut (A) and washer (B) on inside of frame
rail.
MX5624
2. Move brake switch (C) toward front of machine until
plunger is fully retracted when contacting neutral safety
arm.
3. Tighten screw (D) and lock nut.
4. Depress master brake pedal and release. Ensure that
neutral safety arm properly contacts plunger. Adjust if
necessary.
5. Check brake switch for proper operation:
a. Operate machine with PTO switch in on position.
b. While depressing master brake pedal, ensure PTO
disengages.
c. Adjust or replace brake switch if necessary.
Removal:
MX5624
1. Disconnect connector (A) on back of brake switch.
2. Remove screw, lock nut and brake switch from machine.
3. Replace brake switch.
Installation:
• Installation is done in the reverse order of removal.
• Perform steps 2 - 5 in Adjustment section.
• Check brake switch for proper operation.
IMPORTANT: Avoid damage! Improper adjustment
may cause damage to plunger and brake switch.
Adjust brake switch with park brake lock lever in
unlocked position and brakes disengaged.
A
B
D
E
C
B
A
C
D
A
14. Brakes Repair - 690
BRAKES REPAIR
Repair
Brake Linkage Removal and Installation
MX5607
A - Left Turn Brake Arm
B - Right Turn Brake Arm
C - Center Support
D - Master Brake Pedal Support
E - Right Master Brake Arm
F - Support (2 used)
G - Pedal Shaft
H - Bushing (2 used)
I - Upper Brake Link Assembly (2 used)
J - Turnbuckle (2 used)
K - Lower Brake Link Assembly (2 used)
L - Right Brake Cam Arm
M - Brake Return Spring (2 used)
N - Left Brake Cam Arm
O - Left Master Brake Arm
A
B
C
D
E
F
G
I
J
K
LM
M
N
K
J
I
O
H
H
F
15. Brakes Repair - 691
BRAKES REPAIR
Removal:
1. Park machine on level ground.
2. Raise machine and remove front wheels.
3. Remove left brake return spring (M) from latch hook.
4. Remove cotter pin and clevis pin holding upper left
brake link assembly (I) to left master brake arm (O) and left
turn brake arm (A).
5. Remove cotter pin and clevis pin holding left lower brake
link assembly (K) to left brake cam arm (N) and remove
assembly (I, J, and K).
6. Remove right brake return spring (M) from latch hook.
7. Remove cotter pin and clevis pin holding upper right
brake link assembly (I) to right master brake arm (E) and
right turn brake arm (B).
8. Remove cotter pin and clevis pin holding right lower
brake link assembly (K) to right brake cam arm (N) and
remove assembly (I, J, and K).
9. Inspect brake link assemblies and turnbuckles for wear
and damage. Replace as necessary.
Installation:
1. Install lock nuts on upper and lower brake link rods and
connect with turnbuckle. Adjust assembled linkage to a
preset length of 34.3 cm (13.5 in.).
NOTE: The lower right side clevis pin should be
installed with its head facing outward. Place a washer
between the clevis and rue pin.
2. Install brake link assembly on machine starting with
lower clevis first, then upper clevis.
3. Install the brake return springs.
4. Check the left and right turn pedal free play and adjust
turn brake linkage. (See “Turn Brake Adjustment” on
page 688 in this section.)
16. Brakes Repair - 692
BRAKES REPAIR
Turn Brake Pedals Removal and Installation
MX5614
A
O
P
Q
R
T
U
V
B
C
D
E
G
F
H
I
J
K
L
M
N
W
X
Z
S
Y
AA
17. Brakes Repair - 693
BRAKES REPAIR
A - Right Turn Brake Arm
B - Pedal Shaft
C - Drilled Clevis Pin (2 used)
D - Clevis (2 used)
E - Cotter Pin (2 used)
F - Turnbuckle (2 used)
G - Jam Nut, M8 (2 used)
H - Brake Return Spring (2 used)
I - Screw, M8 x 25 (2 used)
J - Support
K - Lock Nut, M8 (2 used)
L - Pivot Bushing
M - Lock Nut, M8 (4 used)
N - Left Turn Brake Pedal Pad
O - Left Turn Brake Pedal
P - Lubrication Fitting
Q - Left Turn Brake Arm
R - Screw, M8 x 30 (2 used)
S - Spring Pin Set
T - Left Master Brake Arm
U - Screw, M8 x 30 (2 used)
V - Right Turn Brake Pedal
W - Right Turn Brake Pedal Pad
X - Lock Nut, M8 (2 used)
Y - Clevis Pin (2 used)
Z - Rue Pin (2 used)
AA- Jam Nut M8 (left-hand thread)
Removal:
1. Park machine on level ground.
2. Lower lift arms or attachment.
3. Open service hatch on operator’s platform.
4. Remove brake return spring (H) from hook on frame.
MX5615
5. Remove screws (R) and lock nuts (M) securing left turn
brake pedal (O) to left turn brake arm (Q).
6. Remove left turn brake pedal.
NOTE: Lower left turn brake arm to gain access and
remove screws on right turn brake pedal.
7. Remove screws (U) and lock nuts (X) securing right turn
brake pedal (V) and right master brake arm (A).
8. Remove right turn brake pedal.
9. Inspect all parts for wear or damage. Replace as
necessary.
Installation:
• Installation is done in the reverse order of removal.
• Make sure slots of inner and outer spring pins for spring
pin set (S) are 180° apart.
• Lubricate left turn brake arm and pedal shaft using
lubrication fitting (P).
• Check turn brake pedal free play and adjust. (See “Turn
Brake Adjustment” on page 688.)
A
M
R
O
Q
V U
X
P
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Brakes Repair - 694
BRAKES REPAIR
Master Brake Pedal Removal and Installation
MX5617
A - Pad
B - Master Brake Pedal
C - Pawl
D - Arm
E - Spring
F - Spring (Master Brake Pedal)
G - Neutral Safety Arm
H - Neutral Safety Link
I - Right Turn Brake Arm
J - Lubrication Fitting
K - Right Master Brake Arm
L - Lock Nut, M8 (2 used)
M - Bracket
N - Support
O - Screw, M10 x 40 (2 used)
P - Spring Pins
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
P
20. Brakes Repair - 695
BRAKES REPAIR
Removal:
1. Park machine on level ground.
2. Unlock park brake.
MX5618
3. Disconnect spring (F) from bracket (M) to release
support (N).
NOTE: Lift up on forward motion pedal to remove rear
screw on master brake pedal.
4. Remove lock nut (L) and screw (O).
5. Remove master brake pedal (B) and bracket.
6. Inspect master brake pedal and pad (A) for wear or
damage. Replace as necessary.
Installation:
• Installation is done in the reverse order of removal.
• Make sure slots of inner and outer spring pins for spring
pin sets (P) are 180° apart.
• Apply grease to lubrication fitting (J) to lubricate right
turn brake arm (I), right master brake arm (K), and pedal
shaft.
• Check master brake pedal free play and adjust. (See
“Turn Brake Adjustment” on page 688.)
• Move park brake lever to lock position. Park brake arm
(D) should activate pawl (C), and lock the support. Adjust if
necessary. (See “Park Brake Lock Lever Assembly
Removal and Installation” on page 696 for repair
procedure.)
• Check neutral safety arm (G) and neutral safety link (H)
for proper operation, and adjust if necessary. (See “F-N-R
Linkage Adjustment” in the Power Train section.)
• Check brake switch for proper operation and adjust.
(See “Brake Switch Adjustment” on page 689.)
B
C
D
E
F
M
N
O
L
21. Brakes Repair - 696
BRAKES REPAIR
Park Brake Lock Lever Assembly Removal and Installation
MX5620
A - Plate
B - Screw
C - Park Brake Lock Lever Assembly
D - Cap Screw
E - Spring
F - Arm
G - Snap Ring
H - Bushing (2 used)
I - Bracket
J - Pawl
K - Flange Nut
L - Lock Nut
L
B
C
A
F
D
E
H
I
J
K
G