Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. 1400 SRM 1215 Drive Axle Removal
General
This manual covers the repair of the drive axle, dif-
ferential, and the wet disc brake.
IDENTIFICATION PLATE
See Figure 1.
1. CARRARO PART NUMBER 2. HYSTER PART NUMBER 3. CARRARO SERIAL NUMBER
Figure 1. Identification Plate
Drive Axle Removal
WARNING
When putting the lift truck on blocks, make
sure the surface is solid, even, and level. Any
blocks used to support the lift truck must be
solid, one-piece units.
1. Put blocks on each side (front and back) of the
steering tires to prevent movement of the lift
truck.
2. Raise the lift truck and put blocks under the
frame so that the drive wheels do not touch the
floor. Put blocks under the counterweight for
stability.
3. Remove the mast assembly as described in the
section Mast Repairs, 2, 3, and 4-Stage Masts
4000 SRM 1148.
WARNING
On lift trucks with pneumatic tires, completely
remove air from tires before removing them
from lift truck. Air pressure in tires can cause
tire and rim parts to explode, which can cause
serious injury or death. Never loosen nuts that
hold together inner and outer wheel halves
when there is air pressure in tire.
4. Remove the wheels.
5. Remove the oil fill/level plugs on both sides of the
drive axle. See Figure 2.
6. Remove the oil drain plug (LH) from the drive
axle to drain the oil from the left-hand side of the
drive axle into a suitable container. See Figure 2.
7. Remove the oil drain plug (RH and center sec-
tion) to drain the oil from the right-hand side
and center section of the drive axle into a suit-
able container. See Figure 2.
8. Remove the brake discs oil drain plug from the
drive axle to drain the brake oil into a suitable
container. See Figure 2.
1
3. Drive Axle Removal 1400 SRM 1215
1. OIL FILL/LEVEL PLUG (LH)
2. OIL DRAIN PLUG (LH)
3. OIL BREATHER (LH)
4. OIL FILL/LEVEL PLUG (RH)
5. OIL DRAIN PLUG (RH AND CENTER SECTION)
6. OIL BREATHER (RH)
7. COOLING OIL INLET PORT
8. COOLING OIL OUTLET PORT
9. MASTER CYLINDER RELIEF PORT
10. SERVICE BRAKE INLET PORT
11. BRAKE DISCS OIL DRAIN PLUG
12. BRAKE OIL BLEEDER VALVE
Figure 2. Oil Fill Plugs and Drain Plugs
9. Remove the parking brake cable. Refer to the
section Brake System 1800 SRM 1135.
10. Disconnect the cooling inlet hose from the mani-
fold on top of the drive axle. See Figure 3.
11. Disconnect the brake inlet hose from the drive
axle. See Figure 3.
12. Disconnect the brake return hose from the drive
axle. See Figure 3.
13. Disconnect the cooling return hose from the man-
ifold on top of the drive axle. See Figure 3.
14. Place blocks under the axle assembly and con-
nect slings and lifting device.
15. Place blocks under the transmission to support
the transmission while removing the drive axle.
16. Remove the capscrews retaining the drive shaft
and remove the drive shaft.
17. Remove the transmission isolator mounting bolt
located on top of the assembly. See Figure 4.
2
5. Drive Axle Removal 1400 SRM 1215
Figure 4. Transmission to Differential
Mounting Bolt
Legend for Figure 4
1. ISOLATORS
2. WASHER
3. WASHER
4. CAPSCREW
5. TRANSMISSION
6. DRIVE AXLE
18. Remove the four mounting capscrews and wash-
ers from the drive axle. See Figure 5.
19. Remove blocks and lower the drive axle assem-
bly. Pull axle forward and away from frame.
20. Place blocks under the differential assembly.
21. Disconnect the cooling outlet crossover hose from
the manifold and the drive axle and remove the
hose. See Figure 6.
22. If necessary, remove the capscrews retaining the
manifold to the center section of the drive axle
and remove the manifold. See Figure 6.
4
10. 1400 SRM 1215 Reduction Gear Assembly
Remove
STEP 1.
Remove the plug using a prybar.
NOTE: Once the lockwasher has been flattened, a new lockwasher must be used.
STEP 2.
Flatten the lockwasher using a punch and hammer.
9
11. Thank you very much
for your reading. Please
Click Here Then Get
More Information.
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
12. Reduction Gear Assembly 1400 SRM 1215
CAUTION
Install two nuts or suitable plastic pipes on the studs to prevent damage to the threads of the studs
from the support bar.
STEP 3.
Install a support bar on the studs to hold the wheel
hub in place as shown. Using a torque multiplier,
loosen the reduction gear assembly retaining nut.
STEP 4.
Remove the socket-head screws fastening the reduc-
tion gear assembly to the wheel hub support.
STEP 5.
Remove the reduction gear assembly from the wheel
hub support.
10
13. 1400 SRM 1215 Reduction Gear Assembly
STEP 6.
Remove and discard the O-ring.
STEP 7.
Remove the ring gear.
1. AXLE SHAFT
2. RING GEAR
STEP 8.
Place the reduction gear assembly in a soft jawed vise
and lock the wheel hub. Remove the retaining nut.
1. RETAINING NUT
11
14. Reduction Gear Assembly 1400 SRM 1215
STEP 9.
Remove the lockwasher.
1. LOCKWASHER
STEP 10.
Remove the washer.
1. WASHER
STEP 11.
Remove the planetary carrier from the wheel hub.
1. PLANETARY CARRIER
12
15. 1400 SRM 1215 Reduction Gear Assembly
STEP 12.
Remove the snap rings.
1. SNAP RING
STEP 13.
Remove the pins with a punch and hammer as shown.
STEP 14.
Remove the reduction gears.
Remove the needle bearings, spacer, and washers
from each reduction gear.
13
16. Reduction Gear Assembly 1400 SRM 1215
STEP 15.
Remove the disk from the planetary carrier.
1. PLANETARY CARRIER
2. DISK
STEP 16.
Remove the wheel hub from the support using a suit-
able extractor and special tool driver ( Hyster Part
Number 1641516). Refer to the section Special Tools.
1. SUPPORT
2. WHEEL HUB
STEP 17.
Remove the bearing cone.
1. BEARING CONE
14