service manual instant download

1. SL30B
SKID STEER LOADER
SERVICE MANUAL
ENGLISH
Serial No. 604.13.057.01
Edition: 07/2002
English- Printed in Italy
Printed by Studio ti

2. 06202
60413057
AVOID ACCIDENTS
Most accidents, whether they occur in industry, on the farm, at home or
on the highway, are caused by the failure of some individuals to follow
simple and fundamental safety rules or precautions. For this reason
MOST ACCIDENTS CAN BE PREVENTED by recognising the real
cause and doing something about it before the accident occurs.
Regardless of the care used in the design and construction of any type
ofequipmentthereareconditionsthatcannotbecompletelysafeguarded
against without interfering with reasonable accessibility and efficient
operation.
Carefully read indications, cautions and safety warning quoted in the
“SAFETY RULES” section.
A careful operator is the best insurance against an accident.
The complete observance of one simple rule would prevent many
thousand serious injuries each year.
That rule is:
Never attempt to clean, oil or adjust a machine while it is in motion.
ATTENTION
On machines having hydraulically, mechanically and/or cable
controlled equipment (such as showels, loaders, dozers, scrapers
etc.) be certain the equipment is lowered to the ground before
servicing, adjusting and/or repairing.
If it is necessary to have the equipment partially or fully raised to
gain access to certain items, be sure the equipment is suitably
supported by means other than the hydraulic lift cylinders, cable
and/or mechanical device used for controlling the equipment.
COPYRIGHT BY FIAT KOBELCO CONSTRUCTION MACHINERY S.p.A.
Product Support - Documentation Centre
Strada di Settimo, 323 - S. Mauro T.SE (TO) ITALY
All rights reserved. Reproduction of text and illustrations in whole or in part, is
strictly prohibited.

3. SL30B
Service Manual
Table of Contents
Description Section No.
General Tab 1
Section Index - General
Safery Precautions I-VIII
Standard Torque Specifications 1001
Fluids and Lubricants 1002
Loctite Product Chart
Engines Tab 2
Section Index - Engines
Engine and Radiator Removal and Installation 2000
Engine Accessories 2001
Fuel System Tab 3
Section Index - Fuel System
Fuel System and Filters 3002
Electrical Tab 4
Section Index - Electrical
Removal and Installation of Electrical Components 4000
Electrical Specifications and Troubleshooting 4002
Battery 4005
Power Train Tab 6
Section Index - Power Train
Removal and Installation of Power Train Components 6000
Hydrostatic System Troubleshooting 6002
Pressure Reducing Valve and Sequence Valve 6003
Piston Pumps 6004
Drive Motors 6005
Sprocket, Chains, and Axle Housings 6007
Brake Valve 6008
Wheels and Tires 6011
Hydraulics Tab 8
Section Index - Hydraulics
Removal and Installation of Hydraulic Components 8000
Hydraulic System Troubleshooting 8002

4. Cleaning the Hydraulic System and Hydrostatic System 8003
Hydraulic Pump 8004
Loader Control Valve 8005
Auxiliary Control Valve 8006
Cylinders 8007
Mounted Equipment Tab 9
Section Index - Mounted Equipment
Pedals and Levers 9000
Loader 9002
ROPS Canopy, Seat, Seat Belts, and Operators Compartment 9003
Auxiliary Hydraulic Installation 9004
Hydraulic and Electrical Schematic
SL30B
Service Manual
Table of Contents
Description Section No.

5. I
PRECAUTIONARY STATEMENTS PERSONAL SAFETY
Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION”, “WARNING”,
and “DANGER”) followed by specific instructions. These precautions are intended for the personal safety of you and
those working with you. Please take the time to read them.
CAUTION: The word “CAUTION” is used where a safe behavioral practice according to operating and
maintenance instructions and common safety practices will protect the operator and others from
accident involvement.
WARNING: The word “WARNING” denotes a potential or hidden hazard which has a potential for
serious injury. It is used to warn operators and others to exercise every appropriate means to avoid
a surprise involvement with machinery.
DANGER: The word “DANGER” denotes a forbidden practice in connection with a serious hazard.
Failure to follow the “CAUTION”, “WARNING”, and “DANGER” instructions may result in serious bodily injury or
death.
MACHINE SAFETY
Additional precautionary statements (“ATTENTION” and “IMPORTANT”) are followed by specific instructions.
These statements are intended for machine safety.
ATTENTION: The word “ATTENTION” is used to warn the operator of potential machine damage if a certain
procedure is not followed.
IMPORTANT: The word “IMPORTANT” is used to inform the reader of something he needs to know to prevent minor
machine damage if a certain procedure is not followed.

6. II
SAFETY PRECAUTIONS
Equipmentshouldbeoperatedonlybythosewhoareresponsibleandinstructedtodoso.Unsafeoperatingpractices
and improper use of the skid-steer loader and its attachments on the part of the operator can result in injuries.
Observe the following safety precautions at all times:
1. Give complete and undivided attention to the job
at hand so that complete control of the loader is
maintained at all times.
2. Be aware of ground conditions, drive slowly over
rough ground and on slopes, keep alert for holes,
ditches and other irregularities that may cause
the loader to overturn.
3. Avoid steep hillside operation which could cause
the loader to overturn.
4. Never transport a loaded bucket at full height.
Operate the loader with the load as low as
possible until it becomes necessary to raise the
boom to discharge the load into a truck, container,
etc.

7. III
5. Reduce speed when turning so there is no danger
of the loader overturning.
6. Never drive up or back up a hill or incline with a
raised boom or the loader could overturn.
7. Always look behind you before backing the loader.
8. Maintain proper transmission oil level to prevent
loss of hydrostatic braking. Check fluid levels on
a regular basis as directed in this manual.
9. Do not allow passengers to ride on the loader at
any time.

8. IV
10. Do not allow children to operate the loader or ride
on the loader at any time.
11. Do not allow anyone to operate the loader without
proper instruction. Legislation in many countries
require that all operators be instructed on the
proper procedures and operation of the machine
before use.
12. Do not operate the loader in any position other
than while in the operator’s seat with the seat belt
securely fastened.
13. Before starting the engine, be sure that all
operating controls are in neutral and parking brake
is engaged.
14. Never operate the loader engine in a closed
building without adequate ventilation.

9. V
15. Refuel the loader outdoors with the engine shut
off. Replace the fuel cap securely. Use an
approved fuel container. Do not smoke when
handling fuel. Avoid spilling fuel.
16. After operating the engine, never touch the
muffler, exhaust pipe, engine or radiator until they
have had time to cool.
17. Dress appropriately - wear relatively tight-fitting
clothing when operating the loader. Loose or torn
clothing can catch in moving parts or controls.
18. Before servicing the loader or any of its attached
equipment, be sure that the attachments are
lowered to the ground or that the boom arms are
supported by the boom lock pins.

10. VI
19. Do not work under overhangs, electric wires, or
where there is danger of a slide.
20. Wear an approved safety hat when operating the
machine and while in any work area. Wear a
suitable hearing protective device such as
earmuffs or earplugs if you are exposed to noise
exceeding 85dBa.
In the interests of safety and personnel comfort,
protective clothing, boots and gloves should be
worn where appropriate.
21. When driving the loader on a road or highway,
use warning lights or warning devices as may be
required by local or state government regulations.
Warning lights and signs are available through
your dealer.
22. Keep the loader clean. Do not allow trash, debris
or other articles to accumulate in the cab, floor or
foot control pedal area that may hinder safe
machine operation.

11. VII
23. Under no circumstances should the frame,
screens, or protective structures be modified.
Never operate the loader with any of the shielding
removed. Never operate the loader without
windows and/or screens in place. Never extend
any part of the body outside of the operator’s area.
24. Always properly tie down the skid-steer loader to
a truck or trailer before transport.
25. Make sure all bystanders are at a safe distance
away from the loader before starting the engine.
26. Do not allow anyone near the loader while the
engine is running and the loader is operational.

12. VIII
27. When using the skid-steer loader to crane objects,
do not allow any person to ride on objects being
craned.
28. Do not use the skid-steer loader as a work platform
for supporting materials.
29. Do not lift personnel or allow personnel to work
while standing in the bucket or on other
attachments. This is not a man-lift.
IMPORTANT: Legislation in many countries state it is the employer’s responsibility to fully instruct each
operator in the proper and safe operation of all operative equipment. Both employer and employee should
therefore thoroughly familiarise themselves with the contents of this manual.
IMPORTANT: Legislation in many countries state it is an employees' responsibility to fully understand the
vehicle operation and ensure safe handling and prevent harm to themselves or others. Therefore thoroughly
familiarise yourself with the contents of this manual.
IMPORTANT: ``Do not put the machine into service until the machinery into which it is to be incorporated
has been declared in conformity with the provisions of the directive’’ 89/392/EEC.

13. SECTION INDEX - GENERAL
Section Title
Section Number
Standard Torque Specifications .................................................................................................................................. 1001
Fluids and Lubricants ............................................................................................................................................... 1002
Loctite Product Chart

14. Section
1001
1001
STANDARD TORQUE SPECIFICATIONS

15. 1001-2
TABLE OF CONTENTS
TORQUE SPECIFICATIONS - DECIMAL HARDWARE ....................................................................................................... 3
Grade 5 Bolts, Nuts, and Studs .................................................................................................................................. 3
Grade 8 Bolts, Nuts, and Studs .................................................................................................................................. 3
TORQUE SPECIFICATIONS - METRIC HARDWARE ........................................................................................................ 4
Grade 8.8 Bolts, Nuts, and Studs ................................................................................................................................ 4
Grade 12.9 Bolts, Nuts, and Studs .............................................................................................................................. 4
Grade 10.9 Bolts, Nuts, and Studs .............................................................................................................................. 4
TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS ........................................................................................... 5
37 Degree Flare Fitting ............................................................................................................................................. 5
Straight Threads with O-ring ...................................................................................................................................... 5
Split Flange Mounting Bolts ....................................................................................................................................... 6
O-Ring Face Seal End .............................................................................................................................................. 6
O-Ring Boss End
Fitting or Lock Nut .................................................................................................................................................... 6
Pipe fittings ............................................................................................................................................................. 7

16. 1001-3
Temp ate Date: 1997_01_13 A t+ to disp ay temp ate i ormatio
TORQUE SPECIFICATIONS - DECIMAL HARDWARE
Use the torques in this chart when special torques
are not given. These torques apply to fasteners with
both UNC and UNF threads as received from
suppliers dry, or when lubricated with engine oil. Not
applicable if special graphities, Molydisulfide
greases, or other extreme pressure lubricants are
used.
Grade 5 Bolts, Nuts, and Studs
Size
Newton
metres
1/4 inch 10 to 12
5/16 inch 21 to 24
3/8 inch 38 to 43
7/16 inch 61 to 69
1/2 inch 94 to 104
9/16 inch 132 to 149
5/8 inch 183 to 210
3/4 inch 325 to 370
7/8 inch 530 to 595
1.0 inch 790 to 890
1-1/8 inch 980 to 1100
1-1/4 inch 1385 to 1555
1-3/8 inch 1810 to 2030
1-1/2 inch 2400 to 2700
Grade 8 Bolts, Nuts, and Studs
Size
Newton
metres
1/4 inch 15 to 16
5/16 inch 30 to 34
3/8 inch 54 to 60
7/16 inch 86 to 97
1/2 inch 132 to 149
9/16 inch 191 to 213
5/8 inch 260 to 293
3/4 inch 480 to 515
7/8 inch 745 to 835
1.0 inch 1120 to 1280
1-1/8 inch 1585 to 1785
1-1/4 inch 2215 to 2235
1-3/8 inch 2930 to 3295
1-1/2 inch 3895 to 4375
NOTE: Use thick nuts with Grade 8 bolts.

17. 1001-4
Temp ate Date: 1997_01_13 A t+ to disp ay temp ate i ormatio
TORQUE SPECIFICATIONS - METRIC HARDWARE
Use the following torques when specifications are not
given.
These values apply to fasteners with both coarse and
fine threads as received from supplier, plated or
unplated, or when lubricated with engine oil. These
values do not apply if graphite or Molydisulfide
grease or oil is used. Use of a click type torque
wrench, or better is required.
Grade 12.9 Bolts, Nuts, and Studs
Usually the torque values specified for grade 10.9
fasteners can be used satisfactorily on grade 12.9
fasteners.
Grade 8.8 Bolts, Nuts, and Studs
Size
Newton
metres
M4 3 to 4
M5 5 to 6
M6 10 to 11
M8 23 to 26
M10 46 to 51
M12 80 to 90
M14 128 to 145
M16 200 to 220
M20 400 to 450
M24 690 to 780
M30 1375 to 1545
M36 2400 to 2700
8.8
Grade 10.9 Bolts, Nuts, and Studs
Size
Newton
metres
M4 5 to 6
M5 8 to 9
M6 14 to 15
M8 33 to 37
M10 65 to 74
M12 114 to 128
M14 183 to 205
M16 285 to 320
M20 555 to 620
M24 955 to 1075
M30 1900 to 2140
M36 3315 to 3730
10.9
12.9

18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

19. 1001-5
Temp ate Date: 1997_01_13 A t+ to disp ay temp ate i ormatio
TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS
37 Degree Flare Fitting
Nom. SAE
Dash Size Tube OD/Hose ID Thread Size Newton metres
-2 5/16 - 24 8 to 9
-3 3/8 - 24 11 to 12
-4 6.4 mm 7/16 - 20 14 to 16
-5 7.9 mm 1/2 - 20 18 to 21
-6 9.5 mm 9/16 - 18 27 to 33
-8 12.7 mm 3/4 - 16 46 to 56
-10 15.9 mm 7/8 - 14 77 to 85
-12 19.0 mm 1-1/16 - 12 107 to 119
-14 22.2 mm 1-3/16 - 12 127 to 140
-16 25.4 mm 1-5/16 - 12 131 to 156
-20 31.8 mm 1-5/8 - 12 197 to 223
-24 38.1 mm 1-7/8 - 12 312 to 338
Straight Threads with O-ring
Nom. SAE
Dash Size Tube OD/Hose ID Thread Size Newton metres
-2 5/16 - 24 8 to 9
-3 3/8 - 24 11 to 12
-4 6.4 mm 7/16-20 20 to 25
-5 7.9 mm 1/2-20 27 to 33
-6 9.5 mm 9/16-18 43 to 54
-8 12.7 mm 3/4-16 73 to 90
-10 15.9 mm 7/8-14 100 to 124
-12 19.0 mm 1-1/16-12 138 to 173
-14 22.2 mm 1-3/16-12 173 to 216
-16 25.4 mm 1-5/16-12 203 to 253
-20 31.8 mm 1-5/8-12 308 to 357
-24 38.1 mm 1-7/8-12 492 to 542

20. 1001-6
Temp ate Date: 1997_01_13 A t+ to disp ay temp ate i ormatio
Split Flange Mounting Bolts
Size Newton metres
5/16-18 20 to 27
3/8-16 27 to 34
7/16-14 47 to 61
1/2-13 74 to 88
5/8-11 190 to 203
O-Ring Face Seal End
O-Ring Boss End
Fitting or Lock Nut
Nom. SAE
Dash Size Tube OD Thread Size
Newton
metres Thread Size
Newton
metres
-4 6.4 mm 9/16-18 23 to 26
-6 9.5 mm 11/16-16 34 to 40 9/16-18 48 to 54
-8 12.7 mm 13/16-16 52 to 57 3/4-16 70 to 78
-10 15.9 mm 1-14 81 to 90 7/8-14 102 to 114
-12 19.0 mm 1-3/16-12 117 to 128 1-1/16-12 142 to 160
-16 25.4 mm 1-7/16-12 152 to 174 1-5/16-12 237 to 254
-20 31.8 mm 1-11/16-12 179 to 201
-24 38.1 mm 2-12 213 to 235

21. 1001-7
Temp ate Date: 1997_01_13 A t+ to disp ay temp ate i ormatio
NOTE: Apply sealant/lubricant to male pipe threads.The first two threads should be left uncovered to avoid system
contamination. Screw pipe fitting into female pipe port to the finger tight position. Wrench tighten fitting to the
appropriate turns from finger tight (TFFT) shown in table above, making sure the tube end of an elbow or tee fitting
is aligned to receive incoming tube or hose fitting.
Pipe fittings
Nom. SAE
Dash Size Thread Size TFFT (Turns For Finger Tight)
-2 1/8 - 27 2.0 - 3.0
-3 1/8 - 27 2.0 - 3.0
-4 1/8 - 27 2.0 - 3.0
-5 1/8 - 27 2.0 - 3.0
-6 1/4 - 18 1.5 - 3.0
-8 3/8 - 18 2.0 - 3.0
-10 1/2 - 14 2.0 - 3.0
-12 3/4 - 14 2.0 - 3.0
-14 3/4 - 14 2.0 - 3.0
-16 1 - 11 1/2 1.5 - 2.5
-20 1 1/4 - 11 1/2 1.5 - 2.5
-24 1 1/2 - 11 1/2 1.5 - 2.5
-32 2 - 11 1/2 1.5 - 2.5