This document provides specifications for the CLAAS Dominator 106 combine harvester, including technical data, dimensions, weights, settings, capacities, and descriptions of components. Key details include a 638 cubic inch engine producing 205 horsepower, a cutting width ranging from 13 to 25 feet, a grain tank capacity of 184.6 US bushels, a transport width of 171-363 inches depending on configuration, and hydraulic oil, transmission oil, and engine oil capacities.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
2. GROUP
INDEX
1 Specifications
2 Sectional View of Machine
3 Drive Schematic
4 Cutterbar
5 Threshing Mechanism
6 Elevators and Crop Delivery
7 Engine and Drives
8 Transmission and Chassis
9 Hydraulic System
10 Steering and Rear Axle
11 Electrical System
12 Auxiliary Equipment
Special Notes
4. DO 106 .... 56
1 SPECIFICATIONS DOMINATOR 106
Technical data 1. 1
Weights 1. 4
Dimensions 1. 5
Settings and capacities 1. 7
DOMINATOR 96
Technical data 1. 9
Weights 1.12
Dimensions 1.13
Settings and capacities 1.15
DOMINATOR 86
Technical data 1.17
Weights 1.20
Dimensions 1.21
Settings and capacities 1.23
DOMINATOR 76
Technical data 1.25
Weights 1.28
Dimensions 1.29
Settings and capacities 1.31
DOMINATOR 66
Technical data 1.33
Weights 1.36
Dimensions 1.37
Settings and capacities 1.39
DOMINATOR 56
Technical data 1.41
Weights 1.44
Dimensions 1.45
Settings and capacities 1.47
5. SPECIFICATIONS DOMINATOR 106
Technical data, dimensions and weights are
given as an indication only. CLAAS reserve
the right to make changes in design and
specifications at any time without previous
notice and rejects all responsibility in case
of errors.
NOTE: Front, rear, right and left refer to
direction of travel.
Cutterbar
Cutting widths
Height adjustment
Cutting height range
Clearance height under
cutterbar skid
Reel drive
Reel height adjustment
Feeder house
Cutterbar clutch
Threshing Equipment
Stone trap
Concave
Disawning
Threshing drum
Threshing mechanism clutch
DO 106 . .,. ,.56
To be sure, always compare settings and filling'
capacities with specifications stated in the
appropriate Operator's Manual for the machine
concerned.
3.90 m 4.50 m 5.10 m 5.70 m 6.60 m 7.50 m
(13ft) (15ft) t17ft) (19ft) (22ft) (25ft)
hydraulic
from 360 mm (14 1/4 in) below ground level
to 1300 mm (51 1/4 in) above ground level.
with floatation springs in use 950 mm (37 112 in)
with floatation springs blocked 1100 mm (43 1/2 in)
belt-operated variable speed drive
hydraulic
chain-type feed rake
hydraulic
standard equipment
adjustable from operator's platform
rear of concave separately adjustable (2nd lever)
width 1580 mm (621/4 in), 12 bars
disawning plates underneath the concave, two and three
disawning plates can be engaged separately
width 1580 mm (62 1/4 in)
diameter 450 mm (17 3/4 in)
six rasp bars, seven drum discs
speed infinitely variable from 650 to 1500 1/min (rpm)
Optional:
a) step pulley drive - 750, 1000, 1200, 1500 1Imin (rpm)
b) slow-speed threshing drum drive kit (chain drive)
from 290 to 680 1/min (rpm)
hydraulic
1.1
6. 00 106 .... 56
SPECIFICATIONS DOMINATOR 106
Straw Walkers
Type
No. of walker racks
No. of walker crankshafts
Speed of walker crankshafts
No. of tine crankshafts
No. of tines per crankshaft
Walker area
Separating area
Cleaning
Type
Wind volume control
Total cleaning area
Grain tank
Capacity
Unloading tube
Engines
Cubic capacity
Max. speed l/min (rpm)
Idle speed 1/min (rpm)
kW (DIN H.P.)
Cooling
Fuel tank capacity
Battery
1.2
step type walkers and intensive separation system
(crankshaft with tines)
six
two
220_5 1/min (rpm)
two
six
7.00 m2
(10 850 sq in)
7.95m2
(12322sqin)
forced air cleaning fan
by infinitely variable fan speed
additional fan shutters (optional)
5.10 m2
(7905 sq in)
6500 litres (178.75 U.K. bushels; 184.6 U.S. bushels)
hydraulically operated position control
Mercedes DM 401.901
10455 cm3
(638 in3
)
2390
1150
151 (205)
water
300 litres (66 Imp. gal, 79 U.S. gaU
12 Volt, 143 Ah
7. 00 106 .... 56
SPECIFICATIONS DOMINATOR 106
Ground drive
Transmission
Ground speeds in kilometers per hour
Forward travel
Reverse travel
Ground speeds in miles per hour
Forward travel
Reverse travel
Traction Wheel Drive
Steering
hydrostatic, controlled by lever on operator's platform
three gear ranges in either forward or reverse
1. and 2. gear range for field operations
3. gear range for road travel
on 23.1-26 R1 / 18.4-34 R1 tyres
1. from 0 to 6.1 km/h (from 0 to 7.7 km/h)
2. from 0 to 8.9 km/h (from 0 to 11.1 km/h)
3. from 0 to 20.0 km/h (from 0 to 25.5 km/h)
1. from 0 to 4.6 km/h (from 0 to 5.8 km/h)
2. from 0 to 6.6 km/h (from 0 to 8.8 km/h)
3. from 0 to 15.3 km/h (from 0 to 19.0 km/h)
on 23.1-26 R1 / 18.4-34 R1 tyres
1. from 0 to 3.8 mph (from 0 to 4.8 mph)
2. from 0 to 5.5 mph (from 0 to 6.9 mph)
3. from 0 to 12.4 mph (from 0 to 15.8 mph)
1. from 0 to 2.9 mph (from 0 to 3.6 mph)
2. from 0 to 4.1 mph (from 0 to 5.5 mph)
3. from 0 to 9.5 mph (from 0 to 11.8 mph)
Figures in brackets are only applicable for certain countries.
In countries with a speed limit of 20 km/h (12.4 mph) for
self-propelled machinery of husbandry, the hydrostatic drive
system incorporates a device that limits the ground speed
accordingly.
via final drive gears in oil bath
hydrostatic
Brakes
Tyres and Tyre Pressures
Foot brake
Hand brake
hydraulic, designed to work independently when the pedal
lock is removed
mechanical, independent of foot brakes
maximum minimum tyre pressure
tyre size tyre maize picker head grain cutterbar
pressure six-row five-row 7.50 m 6.60 m 5.70 m 5.10 m 4.50m 3.90m
four-row (25 ft) (22 ft) (19 ft) (17 ft) (15 ft) (13 ft)
bar (psi) bar (psi) bar (psi) bar (psi) bar (psi) bar (psi)
18.4-3414PR 3.3 (48) - 3.2 (46) 3.2 (46) 3.0 (43) 2.8 (41)
23.1-26 14 PR 2.5 (36) 2.5 (36) 2.3 (33) 2.3 (33) 2.1 (30) 1.9 (27)
28.1-26 12 PR 1.8 (26) 1.8 (26) 1.7 (25) 1.7 (25) 1.6 (23) 1.5 (22)
30.5-32 12 PR 1.5 (22) 1.2 (17) 1.1 (16) 1.1 (16) 1.1 (16) 1.1 (16)
14.5/75-20 8 PR - 3.0 (43) 3.0 (43) 3.0 (43) 3.0 (43) 3.0 (43)
Where ground conditions allow maximum tyre pressure, the maximum tyre pressure should be maintained in order to
obtain the longest possible service life of the tyre.
Torque Settings of Wheel
Bolts and Wheel Nuts
Front wheels wheel nuts with thrust piece H 22
DIN 74361-10 =860 Nm (622 ft Ib)
Rear wheels wheel bolts M 18 x 1.5 =325 Nm (235 ft Ib)
1.3
8. DO 106 .... 56
SPECIFICATIONS DOMINATOR 106
Weights
Combine equipped with 18.4-34 Rl and 14.5/75-20
tyres, empty fuel tank and six cylinder engine:
Determine the total weight of the machine by adding
the weight of the equipment used on the combine to
the weight of the basic machine.
Basic machine (without cutterbar)
With cutterbar and spring tine reel
3.90 m (13 ft)
4.50 m (15 ft)
5.10 m (17 ft)
5.70 m (19 ft)
With bat-type reel
6.60 m (22 ft)
7.50 m (25 ft)
Two cpl. divider assemblies
With straw chopper
With four-row maize picker head
With five-row maize picker head
With six-row maize picker head
With maize head stalk chopper
With wheel weights (one set)
With liquid ballast (magnesium chloride solution) filled into tyres
With extra weights in compliance with road regulations (not for all countries)
Combine Dimensions
9060 kg (19974 Ib)
add 960 kg ( 2116 Ib)
add 1040 kg ( 2292 Ib)
add 1120 kg ( 2469 Ib)
add 1200 kg ( 2446 Ib)
add 1320 kg ( 2910 Ib)
add 1440 kg ( 3175 Ib)
add 50 kg ( 110 Ib)
add 284 kg ( 626 Ib)
add 1260 kg ( 2778 Ib)
add 1510 kg ( 3329 Ib)
add 1740 kg ( 3836 Ib)
add 250 kg ( 551 Ib)
add 104 kg ( 2291b)
add 254 kg ( 560 Ib)
add 300 kg ( 661 Ib)
Turning Diameter, conforming to DIN 70020 Specifications
Wheel Thread
Width over Tyres
Wheel Base
Ground Clearance
front
rear
on 18.4-34 tyres
on 23.1-26 14 PR tyres and
DW 20-26 wheels
on 28.1-26 tyres
adjustable axle
on 18.4-34 tyres
on 23.1-26 14 PR tyres and
DW 20-26 wheels
on 28.1-26 tyres
2510 mm (98 3/4 in)
2550 mm (100 1/2 in)
2780 mm (109 1/2 in)
2300 mm (90 1/2 in)
2980 mm (117 1/4 in)
3140 mm (123 1/2 in)
3500 mm (137 3/4 in)
3650 mm (143 3/4 in)
420 mm (16 1/2 in)
16800 mm (661 1/2 in)
1.4
9. 00 106 .... 56
SPECIFICATIONS DOMINATOR 106
~-----------L------------.....&
Operatjng Position
3760 mm (148 in)
add 415 mm ( 16 3/8 in)
3720 mm (146 1/2 in)
WIDTH B
HEIGHT H
Cutting width 3.90 m 4.50 m 5.10 m 5.70 m 6.60 m 7.50"m
(13 ft) (15ft) (17ft) (19 ft) (22ft) ("25ft)
Overall width 5565 mm 6175 mm 6785 mm 7395 mm 8310 mm 9225 mm
(219 in) (243 in) (267 1/4) (291 1/4) (327 1/4) (363 1/4 in)
Overall widths are with deflectors set out on each side by
600 mm (23 3/4 in).
With four-row (3 m) maize picker head 3260 mm (128 1/4 in)
With five-row maize picker head 4060 mm (159 3/4 in)
With six-row maize picker head 5200 mm (204 3/4 in)
To top of grain tank
When grain tank lid is open
To top of cab
To bottom edge of grain tank
unloading tube 4020 mm (158 1/4 in)
On 23.1-26 or 28.1-26 tyres the height dimensions are being
reduced by approx. 40 mm (1 1/2 in).
LENGTH L Without dividers
With hoop dividers
With long dividers
With short dividers
Witz maize picker head
, With straw hood back panel
adjusted to rearward position
With straw spreader
9190 mm (361 3/4 in)
9550 mm (376 in)
10540 mm (415 in)
10290 mm (405 in)
10220 mm (402 1/4"in)
add 300 mm ( 11 3/4 in)
add 500 mm ( 19 3/4 in)
1.5
10. 00 106 .... 56
SPECIFICATIONS DOMINATOR 106
.......-----------L--------------..
Transport Position
WIDTH B
HEIGHT H
Cutting width 3.90 m 4.50 m 5.10 m 5.70 m 6.60 m 7.50 m
(13ft) (15ft) (17ft) (19 ft) (22ft) (25ft)
Overall width 4365 mm 4975 mm 5585 mm 6195 mm 7110 mm 8025 mm
(171 3/4) (1953/4) (220 in) (244 in) (280 in) (315 in)
With cutterb6r detached 3000 mm (118 in)
With four-row (3 m) maize picker head 3000 mm (118 in)
With five-row maize pic.ker head 3800 mm (149 1/2 in)
With six-row maize picker head 4940 mm (194 1/2 in)
Ta top of grain tank 3760 mm (148 in)
Ta top of cab 3720 mm (146 1/2 in)
On 23.1-26 or 28.1-26 tyres the height dimensions are being
reduced by approx. 40 mm (1 1/2 in).
LENGTH L
1.6
With cutterbar detached
Without dividers
With hoop dividers
With long dividers
With short dividers
With maize picker head
7770 mm (306 in)
9290 mm (365 3/4 in)
9650 mm (380 in)
10640 mm (419 in)
10390 mm (409 in)
10320 mm (406 in)
11. SPECIFICATIONS DOMINATOR 106
SETTINGS AND CAPACITIES
Hydraulic Oil Pressures
Lift hydraulic system
pressure relief valve
Hydrostatic steering system
pressure relief valve
Hydrostatic ground drive:
(LINDE hydrostatic pump BPV 100 S)
Charge pressure
Operating pressure
(SAUER hydrostatic pump SPV 23)
Charge pressure
Operating pressure
Oil Capacities
Transmission gearbox
Final drive gearboxes
Lift hydraulic system
LINDE hydrostatic
ground drive system
SAUER hydrostatic ground
drive system
Engines
Slip clutches
Reel
Main table auger
Upper feed rake shaft
Returns elevator
180 bar (2610 psi)
90+5 bar (1305+72.5 psi)
16 bar ( 232 psi)
420 bar (6091 psi)
14 bar ( 203 psi)
420 bar (6091 psi)
5 litres (4.4 Imp. qt; 5.28 U.S. qt) SAE 90
(M IL-L-21 05 B) API-G L-5-90
Hypoid Transmission Oil
4 litres each (3.5 Imp. qt; 4.2 U.S. qt) SAE 90
(M IL-L-21 05 B) API-G L-5-90
Hypoid Transmission Oil
approx.7 litres (6.2 Imp.qt; 7.4 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to
(DI N 51524) ISO-VG 68 Specifications
approx. 8 litres (7 Imp. qt; 8.5 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to
(DIN 51524) ISO-VG 68 Specifications
approx. 27 litres (23.76 Imp. qt; 28.5 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to
(DI N 51524) ISO-VG 68 Specifications
consult engine instruction book and combine
operator's manual
200 Nm (145 ft Ib)
200 Nm (145 ft Ib)
220 Nm (159 ft Ib)
adjust ratchet clutch so that no play exists
DO 106 .... 56
1.7
12. DO 106 .... 56
SPECIFICATIONS DOMINATOR 106
Shear Bolt
Grain tank unloading system
Knife Register
Reel
Basic setting
Main table auger
Basic setting
Concave
Control (initial) setting
M 10 x 45 DIN 931-8.8
the center of the knife sections should line up with the center
of the cutterbar fingers at each end of the knife stroke
reel drive shaft placed vertically over the knife. The tines
should be adjusted to vertical position.
approx. 15 mm (19/32 in) clearance between auger flights
and bottom of cutterbar
concave entrance: 13 mm (1/2 in)
clearance measured at third concave bar
concave exit:
concave main
adjusting lever:
concave rear
adjusting lever:
3 mm (1/8 in)
clearance measured at third last concave
bar
locked in 3rd hole of quadrant
locked in 1st hole of quadrant
(e = narrow)
Brakes
Steering
1.8
Foot brake
Hand brake
brake must grip when the pedal is depressed through one
third of its total travel
brake should be effective with the..hand-l-e·locked in the first
three to four teeth in the segment
with the steering cylinder piston rod fully extended, the
adjustable stop bolts must be contacting the steering arms
13. DO 106 .... 56
SPECIFICATIONS DOMINATOR 96
Technical data, dimensions and weights are
given as an indication only. CLAAS reserve
the right to make changes in design and
specifications at any time without previous
notice and rejects all responsibility in case
of errors.
NOTE: Front, rear, right and left refer to
direction of travel.
To be sure, always compare settings and filling
capacities with specifications stated in the
appropriate Operator's Manual for the machine
concerned.
5.70 m
(19 ft)
5.10 m
(17 ft)
4.50 m
(15 ft)
3-.90 m
(13 ft)
3.60 m
(12 ft)
hydraulic
from 360 mm (14 114 in) below ground level
to 1300 mm (51 114 in) above ground level
with floatation springs in use 925 mm (36 112 in)
with floatation springs blocked 1075 mm (42 114 in)
belt-operated variable speed drive
hydraulic
chain-type feed rake
belt-operated
Height adjustment
Cutting height range
Clearance height under
cutterbar skid
Reel drive
Reel height adjustment
Feeder house
Cutterbar clutch
Cutterbar
Cutting widths
Threshing Equipment
Stone trap
Concave
Disawning
Threshing drum
standard equipment
adjustable from operator's platform
rear of concave separately adjustable (2nd lever)
width 1320 mm (52 in), 12 bar
disawning plates underneath the concave, two and
three disawning plates can be engaged separately
width 1320 mm (52 in)
diameter 450 mm (17 3/4 in)
six rasp bars, six drum discs
speed infinitely variable from 650 to 1500 1Imin (rpm)
Threshing mechanism clutch
Optional:
a) step pulley drive 800, 1000, 1200, 1500 1Imin (rpm)
a1) additional speed 650 1/min (rpm)
b) slow speed threshing drum drive kit, 3-speed chain
drive: 300, 430 and 550 1/min (rpm)
belt-operated
1.9
14. 00 106 .... 56
SPECIFICATIONS DOMINATOR 96
Straw Walkers
Type
No. of walker racks
No. of walker crankshafts
Speed of walker crankshafts
No. of tine crankshafts
No. of tines per crankshaft
Walker area
Separating area
Cleaning
Type
Wind volume control
Total cleaning area
Grain tank
Capacity
Unloading tube
Engine
Cubic capacity
Max. speed 1Imin (rpm)
Idle speed 1Imin (rpm)
kW (DIN H.P.)
Cooling
Fuel tank capacity
Battery
Ground Drive
a) Mechanical
Clutch
Transmission
Speed range
1.10
step type walkers and intensive separation system
(crankshaft with tines)
five
two
220_5 1/min (rpm)
two
five
5.80 m2
(8990 sq in)
6.60 m2
(10230 sq in)
forced air cleaning fan
by infinitely variable fan speed
additional fan shutters (optional)
4.25 m2
(6588 sq in)
5200 litres (143 Imp. bushels, 147.7 U.S. bushels)
hydraulically operated position control
Mercedes OM 352 A
5675 cm3 (346 in3 )
2600
1150
110 (150)
water
300 litres (66 Imp. gal, 79 U.S. gal)
12 Volt, 110 Ah
variable ground speed, hydraulically controlled
dry single disc clutch
three forward, one reverse gear
on 23.1-26 R 1 tyres
1. Gear 1.6 to 4.0 km/h (0.9 to 2.5 mph)
2. Gear 3.5 to 8.6 km/h (2.4 to 5.3 mph)
3. Gear 8.0 to 19.7 km/h (5.0 to 12.2 mph)
R.-Gear 2.8 to 6.9 km/h (1.7 to 4.3 mph)
15. DO 106 .... 56
SPECIFICATIONS DOMINATOR 96
b) Hydrostatic
Transmission
Ground speeds in kilometers per hour
Forward travel
Reverse travel
Ground speeds in miles per hour
Forward travel
Reverse travel
Traction Wheel Drive
Steering
controlled by lever on operator's platform
three gear ranges in either forward or reverse
1. and 2. gear range for field operation
3. gear range for road travel
on 23.1-26 R1 tyres
1. from 0 to 5.4 km/h (from 0 to· 6.8 km/h)
2. from 0 to 9.9 km/h (from 0 to 12.6 km/h)
3. from 0 to 19.9 km/h (from 0 to 25.3 km/h)
1. from 0 to 4.0 km/h (from 0 to 4.9 km/h)
2. from 0 to 7.4 km/h (from 0 to 8.9 km/h)
3. from 0 to 15.0 km/h (from 0 to 18.0 km/h)
on 23.1-26 R1
1. from 0 to 3.4 mph (from 0 to 4.2 mph)
2. from 0 to 6.2 mph (from 0 to 7.8 mph)
3. from 0 to 12.4 mph (from 0 to 15.7 mph)
1. from 0 to 2.5 mph (from 0 to 3.0 mph)
2. from 0 to 4.6 mph (from 0 to 5.5 mph)
3. from 0 to 11.2 mph (from 0 to 11.2 mph)
Figures in brackets are only applicable for certain countries.
In countries with a speed limit of 20 km/h (12.4 mph) for
self-propelled machinery of husbandry, the hydrostatic drive
system incorporates a device that limits the ground speed
accordingly.
via final drive gears in oil bath
hydrostatic
Brakes
Tyres and Tyre Pressures
Foot brakes
Hand brake
hydraulic, designed to work independently when the pedal
lock is removed
mechanical, independent of foot brake
maximum minimum tyre pressure
tyre maize picker head grain cutterbar
tyre sizes pressure six-row five-row 5.70 m 5.10 m 4.50m 3.90m 3.60 m
four-row (19 ft) (17 ft) (15 ft) (13 ft) (12 ft)
and up
bar (psi) bar (psi) bar (psi) bar (psi) bar (psi) bar (psi)
18.4-34 14 PR 3.3 (48) 3.1 (45) 3.0 (43) 3.0 (43) 2.8 (41) 2.6 (38)
23.1-2612PR 2.1 (30) 2.1 (30) 2.0 (29) 2.0 (29) 1.9 (27) 1.7 (25)
23.1-26 14 PR 2.5 (36) 2.1 (30) 2.0 (29) 2.0 (29) 1.9 (27) 1.7 (25)
28.1-26 12 PR 1.8 (26) 1.6 (23) 1.6 (23) 1.6 (23) 1.5 (22) 1.4 (20)
30.5-3210PR 1.5 (22) 1.1 (16) 1.1 (16) 1.1 (16) 1.1 (16) 1.1 (16)
12.5/80-18 6 PR - 2.7 (39) 2.7 (39) 2.7 (39) 2.7 (39) 2.7 (39)
12.5/80-18 10 PR - 3.0 (43) 3.0 (43) 3.0 (43) 3.0 (43) 3.0 (43)
14.5/75-20 8 PR - 2.4 (35) 2.4 (35) 2.4 (35) 2.4 (35) 2.4 (35)
Where ground conditions allow maximum tyre pressure, the maximum tyre pressure should be maintained in order to
obtain the longest possible service life of the tyre.
Torque Settings of Wheel
Nuts and Wheel Bolts
Front wheels wheel nuts with thrust piece H 22
DIN 74361-10 = 520 Nm (376 ft Ib)
Rear wheels wheel bolts M 18 x 1.5 =325 Nm (235 ft Ib)
1.11
16. DO 106 .... 56
'SPECIFICATIONS DOMINATOR 96
Weights
Combine equipped with 23.1-26 R1 and 12.5/80-18
15 tyres, empty fuel tank and six cylinder engine:
Determine the total weight of the machine·by adding
the weight of the equipment used on the combine to
the weight of the basic machine.
Basic machine (without cutterbar)
With cutterbar and spring tine reel
3.60 m (12 ft)
3.90 m (13 ft)
4.50 m (15 ft)
5.10 m (17 ft)
5.70 m (19 ft)
Two cpl. divider assemblies
With straw chopper
With cab and ventilating system
With four-row maize picker head
With five-row maize picker head
With six-row maize picker head
With maize head stalk chopper
With wheel weights (one set)
With liquid ballast (magnesium chloride solution) filled into tyres
With extra weights in compliance with road regulations
(not for all countries)
Combine Dimensions
7432 kg (16385 Ib)
add 920 kg ( 20281b)
add 960 kg ( 2116 Ib)
add 1040 kg ( 22931b)
add 1120 kg ( 2469 Ib)
add 1200 kg ( 2646 Ib)
add 50 kg ( 11 0 Ib)
add 264 kg ( 582 Ib)
add 260 kg ( 573 Ib)
add 1260 kg ( 2778 Ib)
add 1510 kg ( 3329 Ib)
add 1740 kg ( 3836 Ib)
add 250 kg ( 551 Ib)
add 104 kg ( 229 Ib)
add 210 kg ( 4631b)
add 300 kg ( 661 Ib)
Turning Diameter, conforming to DIN 70020 Specifications
Wheel Tread
Width over Tyres
Wheel Base
Ground Clearance
front
rear
on 23.1-26 12 PR tyres
and DW 16-26 wheels
on 23.1-26 14 PR tyres
and DW 20-26 wheels
on 18.4-34 tyres
on 28.1-26 tyres
wide axle
adjustäble axle
on 23.1-26 12 PR tyres
and DW 16-26 wheels
on 23.1-26 14 PR tyres
and DW 20-26 wheels
on 18.4-34 tyres
on 28.1-26 tyres
2450 mm (96 1/2 in)
2550 mm (100 1/2 in)
2510 mm (98 3/4 in)
2780 mm (109 1/2 in)
2050 mm (80 3/4 in)
2300 mm (90 1/2 in)
2500 mm (98 1/2 in)
2700 mm (106 1/4 in)
3000 mm (118 in)
3140 mm (123 1/2 in)
2980 mm (117 1/4 in)
3500 mm (137 3/4 in)
3650 mm (143 3/4 in)
420 mm (16 1/2 in)
16800 mm (661 1/2 in)
1.12
17. Da 106 .... 56
SPECIFICATIONS DOMINATOR 96
.......-----------L--------------..
Operating Position
WIDTH B Cutting width 3.60 m 3.90 m 4.50 m 5.10 m 5.70 m
(12ft) (13ft) (15ft) (17ft) (19ft)
Overall width 5190 mm 5565 mm 6175 mm 6785 mm 7395 mm
(204 1/4 in) (219 in) (243 in) (267 1/4 in) (291 1/4 in)
Overall widths are with deflectors set out on each side by
600 mm (23 3/4 in).
With four-row (3 m) maize picker head 3260 mm (128 1/4 in)
With five-row maize oicker head 4060 mm (159 3/4 in)
With six-row maize picker head 5200 mm (204 3/4 in)
HEIGHT H
LENGTH L
Ta top of grain tank
When grain tank lid is open
To top of cab
To bottom edge of gran tank
Without dividers
With hoop dividers
With long dividers
With short dividers
With maize picker head
With straw hood back panel
adjusted to rearward position
With straw spreader
3720 mm (146 1/2 in)
add 415 mm ( 16 11/32 in)
3680 mm (144 3{4 in)
3530 mm (139 in)
9190 mm (361 3/4 in)
9550 mm (376 in)
10540 mm (415 in)
10290 mm (405 in)
10220 mm (402 1/4 in)
add 300 mm (11 3/4 in)
add 500 mm (19 3/4 in)
1.13
18. 00 106 .... 56
SPECIFICATIONS DOMINATOR 96
...---- B------.e
Transport Position
......- - - - - - - - - - - L---------------l..
WIDTH B Cutting width 3.60 m 3.90 m 4.50 m 5.10 m 5.70 m
(12ft) (13 ft) (15ft) (17ft) (19 ft)
Overall width 3990 mm 4365 mm 4975 mm 5585 mm 6195 mm
(157 in) (171 3/4) '( 195 3/4) (220 in) (244 in)
With cutterbar detached 3000 mm (118 in)
With four-row (3 m) maize picker head 3000 mm (118 in)
With five-row maize picker head 3800 mm (149 1/4 in)
With six-row maize picker head 4940 mm (194 1/2 in)
HEIGHT L
LENGTH L
1.14
To top of grain tank
To top of cab
With cutterbar detached
Without dividers
With hoop dividers
With long dividers
With short dividers
With maize picker head
3720 mm (146 1/2 in)
3680 mm (144 3/4 in)
7770 mm (306 in)
9290 mm (365 3/4 in)
9650 mm (380 in)
10640 mm (419 in)
10390 mm (409 in)
10320 mm (406 1/4 in)
19. SPECIFICATIONS DOMINATOR 96
SETTINGS AND CAPACITIES
Hydraulic Oil Pressures
Lift hydraulic system
pressure relief valve
Hydrostatic steering system
pressure relief valve
Hydrostatic ground drive:
(LINDE hydrostatic pump BPV 70 S)
Charge pressure
Operating pressure
(SAUER hydrostatic pump SPV 22)
Charge pressure
Operating pressure
Oil capacities
Transmission gearbox
Final drive gearboxes
Lift hydraulic system
LI NDE hydrostatic
ground drive system
SAUER hydrostatic
ground drive system
Engines
Slip clutches
Reel
Main table auger
Upper feed rake shaft
Returns elevator
180 bar (2610 psi)
90+5 bar (1305+72.5 psi)
16 bar ( 232 psi)
420 bar (6091 psi)
14 bar ( 203 psi)
420 bar (6091 psi)
• 6 litres (5.3 Imp. qt; 6.3 U.S. qt) SAE 90
(M IL-L-21 05) API-G L-4-90
Transmission Oil
3 litres each (2.6 Imp. qt; 3.2 U.S. qt) SAE 90
(MIL-L-2105) API-GL-4-90
Transmission Oil
approx.6 litres (5.3 Imp. qt, 6.3 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to
(DIN 51524) ISO-VG 68 Specifications
approx. 8 litres (7 Imp. qt; 8.5 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to
(DIN 51524) ISO-VG 68 Specifications
approx. 27 litres (23.76 Imp. qt; 28.5 U.S. qt)
Hydraulic Oil, H-LP Oils conforming to
(DIN 51524) ISO-VG 68 Specifications
consult engine instruction book and combine
operator's manual
200 Nm (145 ft Ib)
200 Nm (145 ft Ib)
220 Nm (159 ft Ib)
adjust ratchet clutch so that no play exists
DO 106 .... 56
1.15
20. 00 106 .... 56
SPECIFICATIONS DOMINATOR 96
Shear Bolt
Grain tank unloading system
Knife Register
Reel
Basic setting
Main table auger
Basic setting
Concave
Control (initial) setting
M 10 x 45 DIN 931-8.8
the center of the knife sections should line up with the center
of the cutterbar fingers at each end of the knife stroke
reel drive shaft placed vertically over the knife. The tines
should be adjusted to vertical position.
approx. 15 mm (19/32 in) clearance between auger flights
and bottom of cutterbar
concave entrance: 13 mm (1/2 in)
clearance measured at third concave bar
concave exit:
concave main
adjusting lever:
concave rear
adjusting lever:
3 mm (1/8 in)
clearance measured at third last concave
bar
locked in 3rd hole of quadrant
locked in 1st hole of quadrant
(e =narrow)
Brakes
Steering
1.16
Foot brake
Hand brake
brake must grip when the pedal is depressed through one third
of its total travel
brake should be effective with the handle locked in the first
three to four teeth in the segment.
with the steering cylinder piston rod fully extended, the
adjustable stop bolts must be contacting the steering arms
21. DO 106 .... 56
SPECIFICATIONS DOMINATOR 86
TechniCaI data, dimensions and weights are
given as an indication only. CLAAS reserve
the right to make changes in design and
specifications at any time without previous
notice and ejects all responsibilit'! in case
of errors.
NOTE: Front, rear, right and left refer to
direction of travel.
To be sure, always compare settings and filling
capacities with specifications stated in the
appropriate Operator's Manual for the machine
concerned.
5.70 m
(19 ft)
5.10 m
(17 ft)
4.50m
(15 ft)
3.90 m
(13 ft)
3.60 m
(12 ft)
hydraulic
from 360 mm (14 1/4 in) below ground level
to 1300 mm (51 114 in) above ground level
with floatation springs in use 900 mm (35 1/2 in)
with floatation springs blocked 1040 mm (41 in)
belt-operated variable speed drive
hydraulic
chain-type feed rake
belt-operated
Height adjustment
Cutting height range
Cutterbar
Cutting widths
Clearance height under
cutterbar skid
Reel drive
Reel height adjustment
Feeder house
Cutterbar clutch
Threshing Equipment
Stone trap
Concave
Disawning
Threshing drum
standard equipment
adjustable from operator's platform
rear of concave separately adjustable (2nd lever)
width 1320 mm (52 in), 12 bar
disawning plates underneath the concave, two and
three disawning plates can be engaged separately
width 1320 mm (52 in)
diameter 450 mm (17 3/4 in)
six rasp bars, six drum discs
speed infinitely variable from 650 to 1500 1/min (rpm)
Threshing mechanism clutch
Optional:
a) step pulley drive 800, 1000, 1200, 1500 1Imin (rpm)
a1) additional speed 650 1/min (rpm)
b) slow speed threshing drum drive kit, 3-speed chain
drive: 300, 430 and 550 1/min (rpm)
belt-operated
1.17
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. 00 106 .... 56
SPECIFICATIONS DOMINATOR 86
Straw Walkers
Type
No. of walker racks
No. of walker crankshafts
Speed of walker crankshafts
No. of tine crankshafts
No. of tines per crankshafts
Walker area
Separating area
Cleaning
Type
Wind volume control
Total cleaning area
Grain tank
Capacity
Unloading tube
step typ walkers and intensive separation system
(crankshaft with tines)
five
two
220_5 1/min (rpm)
two
five
5.15 m2
(7982.5 sq in)
5.95 m2 (9222.5 sq in)
forced air cleaning fan
by infinitely variable fan speed
additional fan shutters (optional)
4.25 m2
(6588 sq in)
4600 Iitres (126.5 Imp. bushels; 130.6 U.S. bushels)
hydraulically operated position control
Engines
Cubic capacity
Max. speed 1Imin (rpm)
Idle speed 1/min (rpm)
kW (DIN H.P.)
Cooling
Mercedes OM 352
5675 cm3 (346 in3 )
2600
1150
88 (120)
water
Perkins 6.3724
6100 cm3
(372 in3
)
2600
1150
88 (120)
water
Fuel tank capacity
Battery
1.18
300 Iitres (66 Imp. gal; 79 U.S. gal)
12 Volt, 110 Ah
24. DO 106 .... 56
SPECIFICATIONS DOMINATOR 86
Ground Drive
a) Mechanical
Clutch
Transmission
Speed range
Traction Wheel Drive
Steering
Brakes
Tyres and Tyre Pressures
Foot brake
Hand brake
variable ground speed, hydraulically controlled
dry single disc clutch
three forward, one reverse gear
on, 18.4-30 R1 /.23.1-26 R1 tyres
1. Gear 1.6 to 4.0 km/h (0.9 to 2.5 mph)
2. Gear 3.5 to 8.6 km/h (2.4 to 5.3 mph)
3. Gear 8.0 to 19.7 km/h (5.0 to 12.2 mph)
R.-Gear 2.8 to 6.9 km/h (1.7 to 4.3 mph)
via final drive gears in oil bath
hydrostatic
hydraulic, designed to work independently when the pedal
lock is removed
mechanical, independent of foot brake
maximum minimum tyre pressure
tyre size tyre maize picker head grain cutterbar
pressure six-row five-row 5.70 m 5.10 m 4.50m 3.90 m 3.60 m
four-row (19 ft) (17 ft) (15 ft) (13 ft) (12 ft)
bar (psi) bar (psi) bar (psi) bar (psi) bar (psi) bar (psi)
18.4-30 12 PR 2.9 (42) - - - - 2.9 (42)
18.4~34 12 PR 2.9 (42) - 2.9 (42) 2.9 (42) 2.5 (36) 2.4 (35)
23.1-26 12 PR 2.1 (30) 2.0 (29) 1.9 (27) 1.9 (27) 1.7 (25) 1.6 (23)
28.1-26 12 PR 1.8 (26) 1.5 (22) 1.5 (22) 1.5 (22) 1.1 (16) 1.1 (16)
12.5/80-18 6 PR - 2.7 (39) 2.7 (39) 2.7 (39) 2.7 (39) 2.7 (39)
12.5/80-18 10 PR - 2.7 (39) 2.7 (39) 2.7 (39) 2.7 (39) 2.7 (39)
14.5/75-20 8 PR - 2.0 (29) 2.0 (29) 2.0 (29) 2.0 (29) 2.0 (29)
Where ground conditions allow maximum tyre_pressure, the maximLam tyre pressure should be maintained in order to
obtain the longest possible service of the tyre.
Torque Settings of Wheel
Bolts and Wheel Nuts
Front wheels with flange nuts M22 x 1.5
and special washer (Limes) C 22.5 DIN 74361
= 520 Nm (376 ft lb)
Rear wheels M 18 x 1.5 wheel bolts = 325 Nm (235 ft lb)
1.19
25. DO 106 .... 56
SPECIFICATIONS DOMINATOR 86
Weights
Combine equipped with 18.4-30 R1 and 12.5/80-18
Impl. tyres, empty fuel tank, six cylinder engine.
Determine the total weight of the machine by adding
the weight of the equipment used on the combine
to the weight of th"e basic machine.
Basic machine (without cutterbar)
With long lip cutterbar and spring tine reel
3.60 m (12 ft)
3.90 m (13 ft)
4.50 m (15 ft)
5.10m(17ft)
5.70 m (19 ft)
Two cpl. divider assemblies
With straw chopper
With cab and ventilating system
With four-row maize picker head
With five-row maize picker head
With six-row maize picker head
With maize head stalk chopper
With wheel vveights (one set)
With liquid ballast (magnesium chloride solution) filled into
12.5/80-18 rear tyres
With extra weights in compliance with road regulations
(not for all countries)
Combine Dimensions
7170 kg (15807 Ib)
add 920 kg ( 20281b)
add 960 kg ( 2116 Ib)
add 1040 kg ( 2293 Ib)
add 1120 kg ( 24691b)
add 1200 kg ( 2646 Ib)
add 50 kg ( 110 Ib)
add 264 kg ( 5821b)
add 260 kg ( 5731b)
add 1260 kg ( 27781b)
add 1510 kg ( 33291b)
add 1740 kg ( 3836 Ib)
add 250 kg ( 551 Ib)
add 104 kg ( 2291b)
add 210 kg ( 4631b)
add 300 kg ( 661 Ib)
Wheel Tread
Width over Tyres
Wheel Base
Ground Clearance
front
rear
on 18.4-30 tyres
on 23.1-26 tyres
on 18.4-34 tyres
wide rear axle
adjustable rear axle
on 18.4-30 tyres
on 23.1-26 tyres
on 18.4-34 tyres
2522 mm (99 1/4 in)
2450 mm (96 1/2 in)
2510 mm (99 in)
2050 mm (80 3/4 in)
2300 mm (90 1/2 in)
2500 mm (98 1/2 in)
2700 mm (106 1/4 in)
2967 mm (116 3/4 in)
2985 mm (117 1/2 in)
2975 mm (117 in)
3650 mm (143 3/4 in)
380 mm (15 in)
Turning Diameter, conforming to DIN 70020 Specifications
1.20
15900 mm (626 in)