2. Validity of this repair manual
This repair manual applies to the following tractor:
Description Type
Tractor serial number
From to
AXION 800 A61 A6100100 —
1/1Validité de ce manuel de réparation
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/2.1.2/210191/001/EN/T...
3. Complete engine
Technical specifications
Number Value Note – Description
1 920 kg Complete engine
For unspecified tightening torques, refer to the section entitled: "Tightening torques".
WARNING
Lifting heavy components.
Risk of death or serious injury.
► Use certified slings or chains in perfect working order.
► Use a certified hoist in perfect working order.
► Use a certified jack or stand which can support the load.
► Use the jack or stand on a flat, horizontal, sufficiently firm surface.
► Place the jack or stand in a suitable location.
NOTICE
Lubricants and fuels end up in the environment.
Environmental pollution
► Collect and store lubricants and fuels in suitable containers and dispose of them properly.
1/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
4. Special tool
Special tool – Reference no.
Carriage to be uncoupled
No. 00 1148 105 0
Special tool – Reference no.
Extension
No. 00 1148 106 0
2/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
5. Special tool – Reference no.
1
Engine lifting brackets kit
No. 00 1152 870 0
Component parts of the NEF 6 kit
2
Bracket at the front of the engine
No. 1149 878 1/1
3
Bracket at the right-hand side of the engine
No. 1149 878 1/2D
4
Bracket at the left-hand side of the engine
No. 1149 878 1/2G
3/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
6. Special tool – Reference no.
Flywheel rotating tool
No. 00 1150 142 0
Removal
► Drain the engine.
► Drain the air conditioning circuit.
► Drain the pneumatic brake circuit (optional).
► Drain the cooling circuit.
► Remove the engine bonnet.
Engine bonnet
.
► Remove the left-hand tank.
Main tankFunction:01 Engine
.
► Remove the exhaust gas post-treatment system. .
4/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
7. ► Remove bolts (1) and (2) and (6).
► Remove the protective panel (3).
► Disconnect the electric starting motor wiring harnesses (4).
► Remove the electric starting motor (5).
► Remove the bolts (1).
► Move aside the protective panel (2).
5/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
8. ► Remove the clamp (1).
► Remove the bolt (2) from the mounting clamp.
► Remove the coolant hose (3).
► Remove the mounting clamps (1), (2) and (3).
► Mark and remove the rigid pipe connectors.
6/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
9. ► Remove the clamps (1).
► Loosen the flexible pipe connector (2).
► Undo connectors (1) and (2).
► Remove the clamp (3).
► Remove the clamps (4), (5), (6) and remove the hoses (7), (8) and (9).
7/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
10. ► Remove the clamp (1).
► Remove the connector (2) and the bolt (3).
► Remove the air conditioning pipes (4) and (5).
Seal the openings of the air conditioning compressor. Attach the pipes to the cabin.
8/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
11. ► Mark and disconnect the electrical wiring harness (1) of the engine.
► Mark and disconnect the electrical wiring harness (2) of the front linkage.
► Mark and disconnect the electrical wiring harness (3) of the front axle.
► Remove the bolts (1).
► Remove the tank mounting panel (2).
9/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
12. ► Decompress the front axle suspension circuit by acting on the suspended front axle hydraulic block (1).
Decompressing the CARRARO front axle suspension hydraulic circuit
► Remove the clamps (2).
► Undo the flexible pipe connector (1).
► Remove the clamps (2).
► Undo the pipe connectors (1).
10/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
13. ► Uncouple the pipes (2), (3) and (4).
► Remove the bolts (1) from the front axle hydraulic block support.
► Remove the suspended front axle hydraulic block.
► Remove the clamps (1), (2), (3) and (4).
► Uncouple the hydraulic connectors.
► Uncouple the air connectors (5) and (6) (optional).
► Remove the bolts (7) and (8) from the air regulator support (optional).
► Remove the air regulator (9) (optional).
11/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
14. ► Remove the clamps (1).
► Mark and uncouple the hydraulic connectors (2).
► Remove the pipes (3).
► Remove the nuts (1) and (2) from the transmission shaft protective panel.
► Remove the transmission shaft protective panel (3).
12/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
15. ► Remove the bolts (1) and (2) from the transmission shaft.
► Remove the transmission shaft (3).
► Remove the bolts (1) and (2).
► Remove the clamps (3), (4), (5) and (9).
► Uncouple the pipes (6), (7) and (8).
13/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
16. ► Disconnect the connector (10).
► Remove the hose (6).
► Remove the clamps (4) and (5).
► Remove the hose (3).
► Remove the bolts (2).
► Remove the expansion bottle assembly and its support (1).
14/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
17. ► Remove the clamp (4).
► Remove the clamps (3).
► Remove the hoses (1) and (2).
► Remove the connectors (1) and (2).
► Remove the bolt (3) from the support bracket.
► Remove the pipes (4) and (5).
► Remove the bolt (1).
► Remove the wiring harness (2) of the "Visctronic" "C080" fan.
15/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. ► Remove the bolts and nuts (2).
► Remove the turbocharger protective panel (1).
► Remove the bolts (1).
► Remove the nuts (2).
► Remove the subframe (1) with a suitable lifting tool.
16/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN
20. The support weighs 36 kg.
► Remove the nuts (1).
► Remove the apron (2).
► Remove the coolant pipe (1) located at the rear of the cylinder head.
► Undo the nut (1) of the visco coupler.
17/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN