Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4yf04000 and up)

Service Repair Manual
Models
D6H TRACK-TYPE TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6H TRACK-TYPE TRACTOR 4YF
Configuration: D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D6H TRACTOR POWER TRAIN
Media Number -SENR3242-03 Publication Date -01/11/2004 Date Updated -10/01/2017
SENR32420003
Track
SMCS - 4170-015; 4170-016; 4170-076; 4170-077
Separate Track
The machine must be on a level hard surface before a separation of the
track is made. Any time a separation of both tracks is made the
machine must have blocks correctly in position so the machine will not
move.
1. Remove track adjuster cover (1) and the O-ring seal from the roller frame.
The adjuster cylinder for the track is under high hydraulic pressure. Do
not visually inspect the relief valve to see if grease is released when it is
open. Look to see that the track has loosened. Use this warning any time
the tracks are loosened or tightened.
1/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) PO...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

2. Loosen the track as follows:
a. Turn the relief valve (2) one turn counterclockwise to permit grease to be released from the
track adjuster. If the track does not loosen go to Step b.
b. Turn fill valve (3) one turn counterclockwise to permit grease to be released from the track
adjuster. If the track still does not loosen, start the machine and move it forward and backward. If
grease is still not released go to Step c.
c. Install a piece of round bar stock between the bushing and sprocket inside the links. Move the
machine to the rear so the track will be pushed up by the round bar stock. This will put tension on
the track and move the track adjuster in.
3. Move the track until the master link is just above the centerline of rear idler (4). Put wood
blocks under the grouser bar, just below the master link. Move the track to the rear until it has
rigid contact with the wooden blocks.
4. The weight of the master shoe is from 19.5 kg to 37.5 kg (43 lbs to 825 lbs.), depending on
which track the vehicle is equipped. Remove four bolts (5) and master shoe (6).
5. Separate master link (7).
2/13
2020/3/8

Keep away from the front of the machine when the track is pushed off
of the final drive. A minimum distance of 6.1 m (20 ft) is needed in front
of the track to permit the track to move out on to the floor.
6. Fasten a chain to the end of the track and to a wheel loader, or similar machine. Turn the final
drive in a forward direction and let track (8) fall forward, as the wheel loader or similar machine is
moved forward.
7. The weight of the track is from 1676 kg to 2602 kg (3687 lbs. to 5724 lbs.) depending on
which track the machine has on it. Lift the side of the machine and remove the track if necessary.
Connect Track
1. Put the track under the machine. Lower the side of the machine on to track (8).
2. Fasten one end of a chain to track (8) and the other end to a wheel loader or similar machine.
NOTICE
To avoid damage to the track or to the machine, the track must be
pulled in a straight line.
3/13
2020/3/8

3. Pull the track until the track bushings engage with the sprocket segments on the final drive.
4. Start the machine and turn the final drive in a reverse direction to pull the track together.
5. Lift the end of the track and put wooden blocks (9) under the grouser as shown.
NOTE: Make sure the serrations on the master link are free of loose or thick rust, paint, and
lubricants.
6. Align the lower end of master link (7) with the upper end of the master link. Make sure the teeth
of both ends of the master link are engaged.
7. Put track shoe (6) in position on the master link. Put 2P2506 Thread Lubricant on the threads,
body, and washer face of the master link bolts. Install bolts (5) that hold the master link together.
Tighten the bolts to a torque of 400 ± 70 N·m (300 ± 50 lb ft). Tighten the bolts an additional 1/3
of a turn. For inspection purposes, after assembly, the final torque must be a minimum of 680 N·m
(500 lb ft)
4/13
2020/3/8

8. Tighten relief valve (2) and fill valve (3) in the track adjuster to a torque of 35 ± 7 N·m (25 ± 5
lb ft).
NOTICE
Measure the track (sag), distance from a straight line, when the
machine is in its working condition. If dirt and debris are present in its
working condition, then measure the (sag) when normal dirt and
debris are present in the track and its components.
9. Adjust the track tension as follows:
a. Move the machine forward for a distance that is two times the length of the machine. Let it
come to a stop without the use of the brakes.
b. Put a tight line between the grouser tips at the sprocket and front idler.
c. Measure distance (X) from the line to the lowest point of (sag) of the grouser tips. Put 5P960
Multipurpose Type Grease in the track adjuster and make an adjustment to the track until
distance (X) is 115 ± 10 mm (4.53 ± .40 in). This is the sag (curve) in the track between the
sprocket and the front idler.
5/13
2020/3/8

d. Do not tighten the track more if distance (Y) is 150 mm (5.9 in) or more. The track will have to
be removed and reconditioned.
10. Install the track adjuster cover (1) and the O-ring seal onto the roller frame.
Disassemble Track
1. Put the track pin, to be removed, in position behind the front idler as shown.
2. Put blocks (2) in position under the front of the track.
3. Put blocks (3) in position under the track to keep the track away from the track roller frame
when the pressure is released in the track adjuster.
4. Release the pressure in the track adjuster. See topic, Separate Track.
6/13
2020/3/8

5. Put tool (A) in position as shown. Use tool (A) to keep the track in position when the track pins
are removed.
6. Remove the bolts, and use two persons to remove three track shoes (1) over the track pins to be
removed.
7. Fasten a hoist to tooling (B). Put tooling (B) in position against the track pin.
8. Push the track pin out of the track with tool (B), and install tool (C) to hold the track together
until the other track pin is removed.
9. Put tooling (B) in position against track pin (4). Push track pin (4) out of the track, and install
tool (C). Remove tooling (B) from the track.
10. Put tooling (D) in position between links (6) and (7). Use tooling (D) to spread the links apart
far enough to move link (5) away from links (6) and (7).
11. Remove tooling (C) from links (5), (6) and (7).
NOTICE
Use care when moving the links apart so the face of the seals are not
damaged.
12. Fasten a hoist to link (5). Move the link away from links (6) and (7).
7/13
2020/3/8

13. Put a block under link (5) to keep it away from links (6) and (7).
14. Put tooling (D) in position between links (9) and (10). Use tooling (D) to spread the links apart
far enough to remove link assembly (8).
15. Fasten a hoist to link assembly (8).
16. Remove tool (C) from links (9) and (10) and link assembly (8), and remove the link assembly.
17. Remove seal assemblies (11) from the track links.
18. Put the track links and track bushing in position in tooling (E) as shown. Push the track
bushing from track link (6).
19. Put track link (7) and the track bushing in position in tooling (E). Remove the track bushing
from track link (7).
8/13
2020/3/8

20. Use a punch and hammer, and remove plug (12) from stopper (13) in the track pins.
21. Remove stoppers (13) from the track pins.
Assemble Track
NOTE: Check all parts of the track assembly for wear or damage. Make replacements if
necessary. Make sure the parts are clean and dry before assembly.
9/13
2020/3/8

1. Put 1P3482 Adapter (2) [part of tooling (A)] in frame (1) of the press arrangement [part of
tooling (A)] with the counterbore toward the ram as shown.
NOTICE
Use a maximum force of 760 kN (170 000 lb) when the track is
assembled. Excessive press force can cause damage to the thrust rings.
2. Put SAE 90 gear oil on each end of track bushing (4) for a minimum length of 5 mm (.197 in).
3. Use tooling (A), and install track bushing (4) into track link (3). Push the track bushing in until
it makes contact with tooling (A). The track bushing must extend 1.76 ± 0.13 mm (.069 ± .005 in)
above the surface of the track link.
4. Put track link (5), track bushing (4) and track link (3) in position in tooling (B). Install pin (6)
[part of tooling (B)] for alignment purposes. Use tooling (B), and install the track link on the track
bushing until the track bushing makes contact with tooling (B). The track bushing must extend
1.76 ± 0.13 mm (.069 ± .005 in) above the surface of the track link.
NOTICE
The seal assemblies must be completely sealed in the track link
counterbores. The load rings of the seal assemblies must make a
minimum amount of contact with oil. Oil causes the load rings to
expand. This is not desired until after assembly.
10/13
D6H TRACK-TYPE TRACTOR / POWERSHIFT / 4YF04000-UP (MACHINE) P...
2020/3/8

NOTICE
Make sure there is contact at area (X) between the seal and load ring.
5. Use tool (C) to install the seal assemblies (the seals and load rings) in the track links as shown
in illustration A82927P1.
6. Put oil on stoppers (7), and install them in track pins (8). The stoppers must be installed to a
depth of 8 ± 4 mm (.315 ± .157 in) below the surface of the track pins.
11/13
2020/3/8

7. Put tooling (D) in position between the track links. Use tooling (D) to spread the links apart far
enough to install link assembly (9).
8. Fasten a hoist to link assembly (9). Put the link assembly in position, and install tooling (E) to
hold it in place.
9. Put tooling (D) in position between the links in link assembly (9). Use tooling (D) to spread the
links apart far enough to install link assembly (10).
10. Fasten a hoist to link assembly (10). Put the link assembly in position in link assembly (9).
11. Align the pin hole in link assembly (10) with the hole in link assembly (9), and install tool (E).
12. Fasten a hoist to tooling (F). Put tooling (F) and track pin (12) in position on the track links.
NOTE: The pin must be installed with the hole end on the same side of the track assembly for the
entire length of the track assembly. The oil cross hole in the pin must be within 20° of the vertical
centerline of the pin bore and closest to the rail of the link. The pins have a mark on the end for
cross hole location. Also, the pin must be installed with a minimum amount of force to get a
maximum amount of end play 0.13 mm (.005 in) between the bushing and the thrust ring.
13. Install track pin (12) with tooling (F) until the pin extends a maximum of 3.22 mm (.127 in)
beyond the link assembly on both sides.
12/13
2020/3/8

14. Put track pin (11) and tooling (F) in position on the track links. Install track pin (11) until it
extends a maximum of 3.22 mm (.127 in) beyond the link assembly on both sides.
15. Use two persons, and put three track shoes (13) in position. Put 2P2506 Thread Lubricant on
the threads, body, and washer's face of the master link bolts. Install the track shoe bolts and nuts.
Make sure the radius corners of the nuts are away from the links. Tighten the bolts to a torque of
400 ± 70 N·m (300 ± 50 lb ft). Tighten the bolts 1/3turn more. For inspection purposes, after
assembly, the final torque must be a minimum of 680 N·m (500 lb ft).
16. Remove tooling (G).
17. Fill the track pins with a minimum of 50.0 mL (1.7 oz.) of SAE 90 gear oil.
18. Put oil on the plug, and install the plug in the stopper in the end of the track pin with tool (H).
Install the plug until it is even with the end of the stopper.
19. Adjust the track. See topic, Separate And Connect Track in this module for the adjustment
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 21:27:47 UTC+0800 2020
13/13
2020/3/8

Shutdown SIS
Previous Screen
SENR32420004
Sprocket Segments
SMCS - 4155-010
Remove And Install Sprocket Segments
1. Move the machine forward or backward until segment (2) to be removed, is in position as
shown.
2. Remove five bolts and nuts (1) and remove segment (2).
NOTE: The following steps are for installation of the sprocket segments.
3. Make sure the mating surfaces of the sprocket segment and the final drive are clean and free of
rust and scale.
NOTE: Install the segment so the head of the bolts are against the segment, and so the washers
and nuts (1) are against the final drive.
4. Put SAE 30 oil on the threads of the segment bolts. Put the segment in position on the final
drive and install bolts, washers, and nuts (1). Tighten nuts (1) to a torque of 175 ± 40 N·m (130 ±
30 lb ft). Tighten the nuts 1/3 of a turn more.
Sun Mar 8 21:28:37 UTC+0800 2020
1/1
2020/3/8

Shutdown SIS
Previous Screen
SENR32420005
Front Track Roller Frames
SMCS - 4151-011; 4151-012
Remove Front Track Roller Frames
Start By:
a. separate track
NOTE: The track roller frame does not have an oil drain plug. To avoid an oil spill when the front
track roller frame is removed from the rear track roller frame, use a vacuum pump in the opening,
near the track adjuster valve, to remove the oil. If a vacuum pump is not available, the oil will
drain when the front track roller frame is removed from the rear track roller frame.
1. Remove six bolts (1) and guide assembly (2) from each side of the rear track roller frame.
Remove the O-ring seal from each of the guide assemblies.
1/6
2020/3/8

2. Remove one bolt from each side of the front idlers and install tooling (A).
3. Attach one end of tooling (B) to tooling (A). Attach the other end of tooling (B) to a stationary
object. Use tooling (B) to pull the front track roller frame out of the rear track roller frame until
the bearing is free from the seal. Remove tooling (B).
4. The weight of the front track roller frame is 546 kg (1200 lb). Put a nylon strap (3) around the
front track roller frame and attach a hoist. Adjust the strap so the front track roller frame will be
level and remove it from the rear track roller frame.
5. Put the front track roller frame on blocks as shown. Use a torch and remove bearing (4) from
the front track roller frame if necessary.
6. Remove seal assembly (5), ring (6), and bearing (7) from the rear track roller frame.
2/6
2020/3/8

Install Front Track Roller Frame
1. If it is necessary to replace bearing (1), remove the track adjuster from the front track roller
frame. See Remove And Install Track Adjuster in this module for the proper procedure.
2. Put dry ice in the front track roller frame tube to lower the temperature of the tube. Heat bearing
(1) to a maximum temperature of 175° C (350° F). Install bearing (1) onto the front track roller
frame. Install the bearing so that it is a maximum of 1 mm (.039 in) away from the plate at the
front of the roller frame.
3. Install the track adjuster into the front track roller frame. See Remove And Install Track
Adjuster in this module for the proper procedure.
3/6
2020/3/8

4. Install bearing (2) and ring (3) into the rear track roller frame.
NOTICE
Make sure tooling (A) and tooling (B) put pressure on the outer ring of
seal assembly (4) when they are used to install the seal assembly into
the rear track roller frame.
5. Put 7M7456 Bearing Mount on the outer diameter of seal assembly (4). Put seal assembly (4)
and tooling (A) in position in the rear track roller frame as shown.
6. Tighten the two nuts [part of tooling (A)] evenly and pull seal assembly (4) in until it is even
with the front surface of the rear track roller frame.
7. Use tool (B) and install seal assembly (4) to the bottom of the counterbore in the rear track
roller frame.
4/6
2020/3/8

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

8. Put seal guard [tooling (C)] in position on the inner diameter of seal assembly (4).
NOTICE
Use care to avoid causing damage to seal assembly (4) and bearing (2)
when the front track roller frame is installed.
9. Put SAE 30 oil on the outer diameter of the front track roller frame bearing (1).
10. Put a nylon strap around the front track roller frame. Adjust the nylon strap so the front track
roller frame is level. Put the front track roller frame into the rear track roller frame and allow
enough room to remove tooling (C). Remove tooling (C).
11. Install tooling (D) onto the rear track roller frame. Install tooling (E) onto the front track roller
frame. Attach the ratchet pullers [part of tooling (D)] to tooling (E).
12. Evenly, pull the front track roller frame into the rear track roller frame using tooling (D) and
(E). Make sure the grooves in the front track roller frame are aligned with the guide locations.
Remove tooling (D) and (E).
13. Install the bolts that hold the front idler caps and tighten them to a torque of 475 ± 50 N·m
(350 ± 37 lb ft).
5/6
2020/3/8

NOTE: Install guide (5) on the inside of the rear track roller frame first for easier installation.
14. Make sure the guide slots are aligned. Apply Loctite 609 to the mating surface of guides (5)
and the track roller frames. Put guides (5) into the track roller frame and install the six bolts that
hold each one.
NOTE: The tracks must be installed and the correct track adjustment made before the oil level can
be checked in the recoil spring compartment.
15. Fill the recoil spring compartment with oil to the correct level. See the Operation And
Maintenance Guide for the type and capacity of oil to be used.
End By:
a. connect track
Sun Mar 8 21:29:26 UTC+0800 2020
6/6
2020/3/8

Shutdown SIS
Previous Screen
SENR32420006
Recoil Springs
SMCS - 4158-011; 4158-012
Remove Recoil Springs
NOTE: All part numbers mentioned in this operation are part of tooling (A), (B), (C), or (D).
1/11
2020/3/8

Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4yf04000 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (12)

Similar to Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4yf04000 and up)

Similar to Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4yf04000 and up) (9)

More from ufjjdjkskemem

More from ufjjdjkskemem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat d6 h track type tractor (prefix 4yf) service repair manual (4yf04000 and up)