This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It involves using various tools to install the weight assembly and tighten bolts to the specified torques. The instructions describe inserting a pin and bolt into the fuel pump camshaft to position the weight assembly, then tightening another bolt while maintaining a constant torque. The tools are then removed and the front housing is reinstalled.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjsjfjskeksmem
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjkskekdmmenm
The document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a washer and bolt and turning the fuel pump camshaft to insert a timing pin.
2) Installing the weight assembly and tightening the bolt to the specified torque.
3) Removing the tools and installing the front housing.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjjkskefmsemwe
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
This document provides instructions for servicing the automatic timing advance on a 517 TRACK SKIDDER model powered by a 3304 engine. It describes removing the fuel injection pump housing and governor, disassembling the housing, and reassembling the housing. The procedures involve using various tools to install and remove parts like bearings, lifters, and seals. Technicians are advised to keep parts clean and apply engine oil during assembly.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and components to access the housing. Disassembly involves using various tools to remove parts like the camshaft, bearings, and lifters. Reassembly requires installing these parts in reverse order and ensuring proper clearance and positioning.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The key steps are:
1. Remove the fuel injection pump housing from the engine using lifting slings and tools.
2. Disassemble the housing by removing components like the fuel rack, lifters, camshaft, and bearings.
3. Reassemble the housing by pressing in new bearings, installing the camshaft and washer, fitting lifters and the fuel rack, and replacing the cover.
This document provides instructions for servicing the automatic timing advance on a 517 TRACK SKIDDER model powered by a 3304 engine. It describes removing the fuel injection pump housing and governor, disassembling the housing, and reassembling the housing. The procedures involve using various tools to install and remove parts like bearings, lifters, and seals. Technicians are advised to keep parts clean and apply engine oil during assembly.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and tubes connected to the housing. Disassembly requires using several specialized tools to remove parts like the camshaft, bearings, and fuel rack. Reassembly follows the reverse order and notes to lubricate parts with clean oil and ensure proper end play and positioning of components like bearings.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjsjfjskeksmem
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjkskekdmmenm
The document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a washer and bolt and turning the fuel pump camshaft to insert a timing pin.
2) Installing the weight assembly and tightening the bolt to the specified torque.
3) Removing the tools and installing the front housing.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjjkskefmsemwe
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
This document provides instructions for servicing the automatic timing advance on a 517 TRACK SKIDDER model powered by a 3304 engine. It describes removing the fuel injection pump housing and governor, disassembling the housing, and reassembling the housing. The procedures involve using various tools to install and remove parts like bearings, lifters, and seals. Technicians are advised to keep parts clean and apply engine oil during assembly.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and components to access the housing. Disassembly involves using various tools to remove parts like the camshaft, bearings, and lifters. Reassembly requires installing these parts in reverse order and ensuring proper clearance and positioning.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The key steps are:
1. Remove the fuel injection pump housing from the engine using lifting slings and tools.
2. Disassemble the housing by removing components like the fuel rack, lifters, camshaft, and bearings.
3. Reassemble the housing by pressing in new bearings, installing the camshaft and washer, fitting lifters and the fuel rack, and replacing the cover.
This document provides instructions for servicing the automatic timing advance on a 517 TRACK SKIDDER model powered by a 3304 engine. It describes removing the fuel injection pump housing and governor, disassembling the housing, and reassembling the housing. The procedures involve using various tools to install and remove parts like bearings, lifters, and seals. Technicians are advised to keep parts clean and apply engine oil during assembly.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and tubes connected to the housing. Disassembly requires using several specialized tools to remove parts like the camshaft, bearings, and fuel rack. Reassembly follows the reverse order and notes to lubricate parts with clean oil and ensure proper end play and positioning of components like bearings.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
4) Disassembling the housing further by removing items like the fuel rack, lifters, camshaft, and bearings.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tightening it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing the removal process which includes removing various fasteners, lines, and the housing using lifting equipment.
3) It provides instructions for disassembling the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
This document provides instructions for disassembling and assembling the right planetary and brake, power train oil pump, and power train oil pump components of a D6H track-type tractor. It outlines 21 steps to disassemble the right planetary and brake, including removing gears, discs, seals, and other parts. It then provides 22 steps for reassembling these components. It also provides instructions for removing and installing the power train oil pump, which involves disconnecting hoses and removing mounting bolts. Finally, it details 23 steps for disassembling the power train oil pump and 21 steps for reassembling it.
Caterpillar Cat D4E TRACK-TYPE TRACTOR (Prefix 77W) Service Repair Manual.pdffyhsejdkkdmmd3e
The document provides instructions for removing and installing a fuel filter base on a Caterpillar 3304B or 3306B engine. The removal procedure involves using a strap wrench to remove the fuel filter, disconnecting the fuel line from the fuel filter base, and removing two bolts and the fuel filter base from the fuel injection pump housing. The installation procedure instructs to install the fuel filter base with a new gasket if needed, connect the fuel line, and secure with two bolts. Proper cleanliness is emphasized when working with fuel system components.
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdffyhsejdkkdmmd3e
This document provides instructions for removing and installing an alternator on a D4E track-type tractor with a 3304 engine. It describes disassembling the alternator by removing components like the regulator, capacitor, pulley, fan, screws, bearings, and rotor. It then describes reassembling the alternator by cleaning parts and reinstalling components in the reverse order of removal. A similar process is described for removing and installing a fuel priming pump and fuel filter base on 3304 and 3306 engines.
The documents provide instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, and disassembling and assembling the fuel transfer pump for a Caterpillar D5B track-type tractor. The procedures include removing bolts and hoses, installing new gaskets if needed, reconnecting lines, and priming the system once reassembled. Safety notices are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump and fuel filter base on a Caterpillar C9 industrial engine. Key steps include:
- Removing bolts and washers to access the fuel priming pump and remove it from the fuel filter base.
- Disconnecting hoses and sensors before removing bolts to access the fuel filter base.
- Reinstalling by reversing the removal steps, reconnecting hoses and sensors, and priming the fuel system.
The document also provides instructions for removing and installing a unit injector, including disconnecting electrical connectors, removing mounting bolts, and using special tools to access and remove the injector without damage. Reinstallation involves
This service repair manual provides instructions for removing and installing various fuel system components on a Caterpillar D4E track-type tractor with a 3304 engine, including:
1) The fuel priming pump, which is removed by turning off the fuel supply, removing securing bolts and disconnecting tubes. Installation is the reverse of removal.
2) The fuel filter base, which is removed by disconnecting the fuel line and removing securing bolts and washers. Installation includes checking and replacing gaskets if needed.
3) The fuel transfer pump, which is removed by turning off the fuel supply and removing securing bolts and tubes.
More Related Content
Similar to Caterpillar Cat 966E WHEEL LOADER (Prefix 94X) Service Repair Manual (94X06489 and up).pdf
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
4) Disassembling the housing further by removing items like the fuel rack, lifters, camshaft, and bearings.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tightening it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing the removal process which includes removing various fasteners, lines, and the housing using lifting equipment.
3) It provides instructions for disassembling the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
Similar to Caterpillar Cat 966E WHEEL LOADER (Prefix 94X) Service Repair Manual (94X06489 and up).pdf (16)
This document provides instructions for disassembling and assembling the right planetary and brake, power train oil pump, and power train oil pump components of a D6H track-type tractor. It outlines 21 steps to disassemble the right planetary and brake, including removing gears, discs, seals, and other parts. It then provides 22 steps for reassembling these components. It also provides instructions for removing and installing the power train oil pump, which involves disconnecting hoses and removing mounting bolts. Finally, it details 23 steps for disassembling the power train oil pump and 21 steps for reassembling it.
Caterpillar Cat D4E TRACK-TYPE TRACTOR (Prefix 77W) Service Repair Manual.pdffyhsejdkkdmmd3e
The document provides instructions for removing and installing a fuel filter base on a Caterpillar 3304B or 3306B engine. The removal procedure involves using a strap wrench to remove the fuel filter, disconnecting the fuel line from the fuel filter base, and removing two bolts and the fuel filter base from the fuel injection pump housing. The installation procedure instructs to install the fuel filter base with a new gasket if needed, connect the fuel line, and secure with two bolts. Proper cleanliness is emphasized when working with fuel system components.
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdffyhsejdkkdmmd3e
This document provides instructions for removing and installing an alternator on a D4E track-type tractor with a 3304 engine. It describes disassembling the alternator by removing components like the regulator, capacitor, pulley, fan, screws, bearings, and rotor. It then describes reassembling the alternator by cleaning parts and reinstalling components in the reverse order of removal. A similar process is described for removing and installing a fuel priming pump and fuel filter base on 3304 and 3306 engines.
The documents provide instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, and disassembling and assembling the fuel transfer pump for a Caterpillar D5B track-type tractor. The procedures include removing bolts and hoses, installing new gaskets if needed, reconnecting lines, and priming the system once reassembled. Safety notices are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump and fuel filter base on a Caterpillar C9 industrial engine. Key steps include:
- Removing bolts and washers to access the fuel priming pump and remove it from the fuel filter base.
- Disconnecting hoses and sensors before removing bolts to access the fuel filter base.
- Reinstalling by reversing the removal steps, reconnecting hoses and sensors, and priming the fuel system.
The document also provides instructions for removing and installing a unit injector, including disconnecting electrical connectors, removing mounting bolts, and using special tools to access and remove the injector without damage. Reinstallation involves
This service repair manual provides instructions for removing and installing various fuel system components on a Caterpillar D4E track-type tractor with a 3304 engine, including:
1) The fuel priming pump, which is removed by turning off the fuel supply, removing securing bolts and disconnecting tubes. Installation is the reverse of removal.
2) The fuel filter base, which is removed by disconnecting the fuel line and removing securing bolts and washers. Installation includes checking and replacing gaskets if needed.
3) The fuel transfer pump, which is removed by turning off the fuel supply and removing securing bolts and tubes.
The document provides instructions for removing and installing a fuel priming pump on a Caterpillar D4E track-type tractor with a 3304 engine. It describes disconnecting fuel lines, removing mounting bolts and base, and reversing the steps for installation. Separate sections cover removing and installing the fuel filter base and removing the fuel transfer pump by disconnecting lines and removing mounting bolts.
The document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. It describes removing components like lines, covers, and bolts. It explains using tools like an impeller puller and spanner wrench. The assembly section describes cleaning parts, installing bearings, camshafts, and other components in the correct order and orientations.
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap to connect fittings, removing and installing the muffler, removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing and installing the primary fuel filter base.
2) The procedures include identifying required tools, disconnecting lines and electrical connections, removing mounting hardware, and installing components in the reverse order of removal while taking appropriate safety precautions.
3) Detailed illustrations accompany each procedure to show component locations and the correct installation orientation. Torque specifications and lubrication requirements are provided where needed.
The document provides instructions for removing and installing fuel lines, filters, and pumps on a C32 industrial engine. It describes:
- Marking and removing existing fuel lines and replacing any worn or damaged lines.
- Installing new fuel lines according to best practices like preventing contact or twisting, using proper lengths and bends, and tightening securely.
- Removing the fuel filter and water separator by turning off fuel, using a strap wrench, and disconnecting hoses and bolts.
- Installing the fuel filter and water separator by reconnecting hoses and bolts, adding a new filter, and turning fuel back on.
- Removing the fuel transfer pump by turning off fuel
This document provides instructions for removing and installing various fuel system components on a C32 Industrial Engine, including:
- The fuel priming pump, fuel filter base, fuel lines, and fuel transfer pump. Detailed step-by-step removal and installation procedures are provided along with required tools. Best practices are outlined for properly installing nonmetallic fuel lines.
This document provides instructions for removing and installing various fuel system components on a C32 Industrial Engine BT4, including:
- The fuel priming pump, which involves disconnecting fuel lines and removing bolts.
- The fuel filter base, which requires disconnecting harness assemblies, hoses, and removing bolts to access sensors.
- Nonmetallic fuel lines, with details on marking, removing, and installing lines, using the proper hose length and avoiding contact with other parts.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Inlet and exhaust valves, springs, and related parts.
2) Inlet and exhaust valve guides.
3) Inlet and exhaust valve seat inserts.
4) The engine oil filter base.
The procedures describe the required tools and provide illustrations showing the parts. Safety notices are included regarding spring-loaded components.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing brackets, bolts, and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It involves the following steps:
1. Draining the coolant from the cooling system.
2. Using a strap wrench to remove the engine oil filter.
3. Disconnecting a hose assembly and removing bolts to take off the engine oil filter base and oil seal.
4. Removing the engine oil cooler and gasket.
The installation procedure is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Cleaning and installing replacement parts in the reverse order
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a 3054E industrial engine. It includes removal and installation procedures with required tools and safety notices. The procedures describe removing/installing the exhaust manifold gasket, setscrews, and turbocharger. For valves, it describes removing/installing the valve springs, retainers, keepers, and stem seals while ensuring the piston is at top dead center.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966D WHEEL LOADER 94X
Configuration: 966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935398
Automatic Timing Advance - Install
SMCS - 1272-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4186 Fuel Pump Timing Pin 1
B 0L-2070 Bolt 1
C 5P-7307 Engine Turning Tool 1
D 4C-9874 Spanner Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00476281
1. Install washer (1) and bolt (2). Ensure that the cover of the fuel pump housing is removed.
Turn the fuel pump camshaft in the direction of the engine rotation until Tool (A) can be
installed in the notch of the camshaft.
2. Install Tool (A) and (B) into position. Install the weight assembly for the timing advance on
the fuel injection pump camshaft.
Illustration 2 g00476286
3. Use Tool (D) on the automatic timing advance and maintain a constant torque of 68 N·m
(50 lb ft). Tighten the bolt that fastens the automatic timing advance to the fuel pump
camshaft to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
4. Remove Tools (A), (B), (C) and (D). Install the starting motor.
End By: Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 27 08:01:45 UTC+0800 2020
2/2
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966D WHEEL LOADER 94X
Configuration: 966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
Illustration 2 g00452289
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/5
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g00452292
3. Remove center bolt (3) and spacer (4).
Illustration 4 g00452293
4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown.
Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection
pump camshaft.
5. Remove Tool (A) and bolt (3).
Illustration 5 g00452301
3/5
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9).
Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6)
with the filter and the gasket.
Illustration 6 g00452302
7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket.
Remove tube assembly (13).
Illustration 7 g00452343
8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor.
Note: Remove the heat shield (not shown) if equipped.
9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the
washers. Remove the fuel injection pump housing and the governor from the engine. To
safely remove the fuel injection pump housing and the governor, use two technicians or a
suitable lifting device. The weight of the 3304B fuel injection pump housing and governor
is 24 kg (53 lb). The weight of the 3306B fuel injection pump housing and governor is
32 Kg (70 lb).
10. Remove the O-ring seals from the fuel injection pump housing and the governor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 27 08:02:41 UTC+0800 2020
4/5
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966D WHEEL LOADER 94X
Configuration: 966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01139602
Fuel Injection Pump Housing - Disassemble
SMCS - 1253-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
Start By:
A. Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
B. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00456860
1. Remove cover (1) and the gasket.
Illustration 2 g00456923
2. Remove fuel rack (2) from the fuel injection pump housing.
Illustration 3 g00456924
2/5
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Note: If the original lifters are being reused in the fuel injection pump housing, place
identification marks on the lifters in order to identify the locations.
3. Remove lifters (3) from the fuel injection pump housing.
Illustration 4 g00456925
4. Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order
to remove snap ring (4) .
Illustration 5 g00456926
5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump
housing in order to loosen washer (5). Remove washer (5) .
3/5
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 6 g00456927
6. Remove camshaft (6) .
Illustration 7 g00456928
7. Remove bearings (7) from the drive end of the fuel injection pump housing.
Illustration 8 g00456930
8. Remove bearings (8) from the governor end of the fuel injection pump housing.
4/5
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966D WHEEL LOADER 94X
Configuration: 966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01138035
Fuel Injection Pump Housing - Assemble
SMCS - 1253-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C
6V-2016 Plate 1
0S-1594 Bolt 2
6V-4818 Driver 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
1/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00457491
1. Use Tool (B) in order to install large bearing (1) in the governor end of the fuel injection
pump housing. Bearing joint (3) should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 0.25 ± 0.20 mm (.010 ± .008 inch) below the
surface of the fuel injection pump housing.
2. Use Tool (B) in order to install small bearing (2) in the governor end of the fuel injection
pump so that Tool (B) is 7.16 ± 0.13 mm (.282 ± .005 inch) below the surface of the fuel
injection pump housing.
Illustration 2 g00457492
3. Use Tool (B) in order to install large bearing (4) in the drive end of the fuel injection pump
housing. The bearing joint should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 1.00 ± 0.25 mm (.039 ± .010 inch) below the
surface of the fuel injection pump housing.
2/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g00457493
4. Install the plate of Tool (C) on the drive end of the fuel injection pump in order to install
small bearing (5) for the rack. Use clean grease in order to hold the new driver for the rack
bearing of Tool (C). Install the driver and the bearing in the plate. Ensure that the groove in
the driver is aligned with the pin in the plate and use a hammer to push the bearing into
position. The bearing will be installed to the correct depth when the shoulder of the driver is
against the plate.
5. Remove Tool (C) from the fuel injection pump housing. The fuel rack bearing must be
installed so that the fuel rack bearing is 0.25 ± 0.25 mm (.010 ± .010 inch) below the surface
of the housing.
Illustration 4 g00457494
6. Install camshaft (6) .
3/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g00458729
7. Put the fuel injection pump housing upright, as shown. Place a wood block under the
camshaft.
8. Put washer (7) over the end of the camshaft. Use Tool (B) and spacer (8) in order to push
the washer against the seat on the camshaft. Spacer (8) has an inside diameter of 38.1 mm
(1.50 inch) and a length of 31.75 mm (1.250 inch). The camshaft must have an end play of
0.18 ± 0.08 mm (.007 ± .003 inch) when the washer is pushed against the shoulder of the
camshaft.
Illustration 6 g00457495
9. Use Tool (A) in order to install snap ring (9) .
4/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 7 g00458730
Note: Check the condition of the new lifters. Replace the lifters, if necessary. If the original
lifters are being reused, place the lifters in the original locations. New lifters are identical,
and the new lifters can be placed in any order.
10. Install six lifters (10) in the fuel injection pump housing. Ensure that the groove in the lifter
is aligned with the pin in the fuel injection pump housing.
Illustration 8 g00458731
11. Install rack (11). Ensure that the groove in the end of the rack is aligned with the ear (tab) of
the fuel rack bearing that is at the drive end of the fuel injection pump housing.
5/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 9 g00458732
12. Install the gasket and cover (12) .
End By:
a. Assemble the governor. Refer to Disassembly and Assembly, "Governor - Assemble".
b. Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 27 08:04:32 UTC+0800 2020
6/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966D WHEEL LOADER 94X
Configuration: 966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111133
Fuel Injection Pump Housing and Governor - Install
SMCS - 1286-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 4C-9874 Spanner Wrench 1
C 6V-4186 Fuel Pump Timing Pin 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The No. 1 piston must be set at the top center position (TC) in order to perform all of the
timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft rotation is
given.
1/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00460164
1. Remove the electric starting motor.
2. Install Tool (A) into the flywheel housing, as shown.
3. To find the TC position for the No. 1 piston, perform the following procedure:
a. Turn the flywheel clockwise or turn the flywheel in the opposite direction of the
engine rotation for approximately 30 degrees. This removes all play from the timing
gears.
Note: If you go past the bolt hole, repeat Step 3.a.
Illustration 2 g00460248
b. Remove plugs (1) and (2) .
2/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g00460252
c. Turn the flywheel counterclockwise until a 3/8-16 X 3 1/2 NC bolt (4) can be
installed in the flywheel through the hole in the flywheel housing. The No. 1 and No.
6 pistons are now at the TC position. Plug (2) was removed for viewing through
inspection hole (3) .
Note: The No. 1 piston is on the compression stroke when the valves of the No. 1
cylinder are closed. The rocker arms for the inlet valves and for the exhaust valves
must have slight side-to-side movement.
d. In order to check the position of the inlet and exhaust valves, remove the valve
mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
Remove and Install".
4. If the No. 1 piston is not on the compression stroke, remove bolt (4) and turn the flywheel
for 360 degrees counterclockwise. Install bolt (4). The No. 1 piston is now at the TC
position.
Illustration 4 g00460258
Typical example
3/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 5. Install Tool (C) in the fuel injection pump housing, as shown. Push on Tool (C) and turn
fuel injection pump camshaft (8). When Tool (C) engages the groove (slot) in the camshaft,
the fuel injection pump is in the TC position for the No. 1 piston.
Note: Check the condition of the O-ring seals. Replace the O-ring seals, if necessary.
6. Ensure that O-ring seals (5), (6), (7) and (9) are in position on the fuel injection pump
housing and the governor. Put clean engine oil on the seals.
Illustration 5 g00460259
7. Attach a hoist and put the fuel injection pump housing and the governor in position on the
timing gear plate and the oil manifold. Install three nuts (11), two bolts (10) and the
washers. Ensure that Tool (C) remains in place.
Illustration 6 g00460341
8. Install washer (12) with the large side outward. Install bolt (13) finger tight. Ensure that
Tool (C) is in the notch in the camshaft of the fuel injection pump.
4/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 7 g00460342
9. Install Tool (B) on the fuel pump drive gear. Apply 68 N·m (50 lb ft) of force to the fuel
pump drive gear with timing bolt (3) in position in the flywheel and Tool (C) in position in
the fuel system. Apply this force in a clockwise direction when the engine is viewed from
the front. Use Tool (B) and a suitable torque wrench. Hold the 68 N·m (50 lb ft) of force on
Tool (B) and torque the drive gear bolt to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
Remove Tool (B) and Tool (C) from the fuel pump and remove bolt (3) from the flywheel.
10. Use Tool (A) and turn the flywheel for two complete revolutions. When bolt (3) goes in the
hole in the flywheel and Tool (C) is installed in the notch in the camshaft, the timing is
correct.
11. Install plugs (1) and (2) .
12. Remove Tool (A). Install the electric starting motor.
13. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Illustration 8 g00460343
14. Put cover (14) and the gasket in position. Install four bolts (15) .
15. Put the fuel filter base, the gasket, and fuel filter (16) in position. Install two bolts (19) and
the washers.
5/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 16. Install tube assemblies (21) and (22). Connect wire (20). Connect hoses (17) and (18) .
Illustration 9 g00589938
17. On the 3304B engines, install the strainer assembly in the turbocharger with the screen
downward. Install the gasket, the oil inlet line and the bolts. Install the O-ring seal on oil
drain line (25). Apply clean engine oil to the O-ring seal and install the gasket. Connect oil
drain line (25) and install the bolts. Install the clamps on the oil line.
Illustration 10 g00460346
18. Put cover (24) in position. Install nuts (23) and six washers. Tighten nuts (23) to a torque of
27 ± 7 N·m (20 ± 5 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 27 08:05:28 UTC+0800 2020
6/6
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966D WHEEL LOADER 94X
Configuration: 966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00886792
Governor - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 6V-2163 Spring Clamp 1
C 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the fuel injection pump housing and the governor. Refer to Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Remove".
Note: To remove the governor for the disassembly of the fuel injection pump housing, perform
Steps 1, 2, 16, 22, 24, 25, 26, 27, 30, 32 and 34.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00453006
1. Remove fuel ratio control (1) from governor (2) .
Illustration 2 g00453007
Note: Illustration 2 shows the fuel ratio control that is still connected.
2. Remove six bolts (3), two bolts (5), housing (4) and the gasket.
Illustration 3 g00453008
2/12
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 3. Remove governor spring (7), seat (6) and the washers.
Illustration 4 g00453009
4. Remove six bolts (8), cover (9) and the gasket. Use Tool (A) in order to remove seal (10) .
Illustration 5 g00453010
5. Remove low idle adjustment screw (12) and spring (11) .
3/12
966E WHEEL LOADER 94X06489-UP (MACHINE) POWERED BY 3306 ENGINE...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...