𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 651E WHEEL SCRAPER 5XR
Configuration: 651E Scraper 5XR00001-UP (MACHINE)
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i03335401
Gear Group (Rear) - Remove
SMCS - 1206-011; 1212-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-0483(1)
Drive Plate 1
1U-5839 Bearing Puller 1
B FT-1342 Guide Bolt 2
(1)
Part of the 1P-0510 Driver Group
Start By:
a. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: There are many possible configurations of the rear gear group and flywheel housing. The
following procedure illustrates a typical example.
1. Use the following procedure for disassembly of the adapter assemblies.
1/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00586481
Typical example
a. Support adapter assembly (1) so that the gear assembly can be pressed out of the
adapter assembly. Press gear assembly (2) out of the adapter assembly.
Illustration 2 g00586630
Typical example
b. Use Tooling (A) in order to remove bearing (3) from the gear assembly.
Illustration 3 g00586904
Typical example
2/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. c. Use a press in order to remove bearing (4) from adapter assembly (1).
Illustration 4 g00586907
Typical example
d. Remove bolts (5) and ring (6) from adapter assembly (1).
e. Remove O-ring seal (7) from adapter assembly (1).
Illustration 5 g00586910
Typical example
f. If necessary, remove race (8) from adapter assembly (1).
3/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 6 g00587590
Typical example
2. With the flywheel housing in a horizontal position, remove bolts (9) from shafts (10).
Note: The bearings that are located toward the flywheel will fall when gear (11) and gear
(12) are removed. Hold these bearings in position when the gears are removed.
3. Remove balancer gear (12) and idler gear (11).
4. Use the following procedure for disassembly of balancer gear (12).
Illustration 7 g00587608
Typical example
a. Remove shaft (13), spacer (15), bearing (14), and bearing (16) from balancer gear
(12).
Illustration 8 g00587624
Typical example
b. Remove bearing cup (17) from balancer gear (12).
Note: The bearing cups will be damaged from the removal. Use new parts for
replacement.
4/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 9 g00587629
Typical example
c. Remove spacer (18) from gear (12).
d. Remove bearing cup (19).
e. If necessary, remove ring (20) from gear (12).
5. Use the procedure in Step 4 in order to disassemble idler gear (11).
Illustration 10 g01712733
6. Install Tooling (B) in the crankshaft. Remove gear (20A).
7. Remove the O-ring seal from gear (20A).
5/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 11 g00587666
Typical example
8. Remove bolts (21). Remove camshaft gear (22).
Illustration 12 g00587668
Typical example
9. If necessary, remove dowel (23).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 16:35:20 UTC+0800 2021
6/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 651E WHEEL SCRAPER 5XR
Configuration: 651E Scraper 5XR00001-UP (MACHINE)
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i03335022
Gear Group (Rear) - Install
SMCS - 1206-012; 1212-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B FT-1342 Guide Bolt 2
C 1P-0524(1)
Drive Plate 1
D 1P-0513(1)
Drive Plate 1
(1)
Part of the 1P-0520 Driver Group
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: There are many possible configurations of the rear gear group and flywheel housing. The
following procedure illustrates a typical example.
1/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g00587668
Typical example
1. Install dowel (23) in the camshaft if the dowel was removed.
Illustration 2 g00587666
Typical example
2. Install camshaft gear (22) in position on the camshaft. Install four bolts (21).
Illustration 3 g01712733
3. Install the O-ring seal on gear (20A).
2/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 4. Lightly lubricate the seal on the end of the crankshaft with clean engine oil.
5. Install Tooling (B) in the crankshaft. Install gear (20A).
6. Use the following procedure for assembly of balancer gear (12).
Illustration 4 g01717018
a. Install ring (20), bearing cup (19), and spacer (18) in balancer gear (12).
Note: Spacer (18) must be installed on the deepest side of gear (12) and against ring
(20).
Illustration 5 g01712754
b. Use a press and Tooling (C) in order to install bearing cup (17). Install bearing cup
(17) on the side of the gear that is stamped with the timing mark. Bearing cup (17)
should be in contact with the spacer.
3/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 6 g00587608
Typical example
c. Install bearing (16), spacer (15), bearing (14), and shaft (13) in gear (12).
7. Use the procedure in Step 6 in order to assemble idler gear (11).
Illustration 7 g00587895
Typical example
8. Place idler gear (11) and balancer gear (12) in position on the flywheel housing. Make sure
that the oil holes in shafts (10) are in alignment with the holes that are in the flywheel
housing.
Note: Install balancer gear (12) with the timing mark toward the flywheel housing.
9. Install bolts (9).
10. Use the following procedure in order to assemble adapter assemblies (1).
4/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 8 g00586910
Typical example
a. If the bearing race was removed, install race (8). Install race (8) in adapter assembly
(1) until the race makes contact with the counterbore.
Illustration 9 g00586907
Typical example
b. Install ring (6), bolts (5), and O-ring seal (7) on adapter assembly (1).
Illustration 10 g01712644
c. Heat bearing (3) to 135 °C (275 °F) for approximately 30 minutes.
5/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. d. Install bearing (3) on gear (2) until the bearing makes contact with the counterbore.
Illustration 11 g00588013
Typical example
e. Install gear (2) and the bearing in adapter assembly (1).
Illustration 12 g01712873
f. Use a press and Tooling (D) in order to install bearing (4) in adapter assembly (1).
Install the bearing until the bearing makes contact with the counterbore.
End By:
a. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 16:36:15 UTC+0800 2021
6/6(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 651E WHEEL SCRAPER 5XR
Configuration: 651E Scraper 5XR00001-UP (MACHINE)
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i04406249
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
FT-1341 Bracket Assembly 1
1B-3623 Bolt 2
B FT-1342 Guide Bolt 2
C 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g00578443
Typical example
1. Remove six bolts (1) that hold the flywheel in position.
2. Install Tool (A) in order to hold the crankshaft gear in position.
3. Remove the remainder of bolts (1) .
Illustration 2 g00578444
Typical example
4. Install Tools (B) .
2/3(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 3 g00578445
Typical example. Tooling (C) is not the tooling called out in the Table.
5. Fasten Tool (C) to a hoist and place the tool in position in the groove of flywheel (2) .
6. Pull flywheel (2) onto Tool (A) .
7. Remove Tool (A) .
8. Remove Flywheel (2) with Tool (C) .
The weight of the flywheel is approximately 78 kg (172 lb).
9. If necessary, remove the ring gear from flywheel (2) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 16:37:11 UTC+0800 2021
3/3(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 651E WHEEL SCRAPER 5XR
Configuration: 651E Scraper 5XR00001-UP (MACHINE)
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i04406250
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1342 Guide Bolt 2
B 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Heat the ring gear to a maximum temperature of 300 °C (572 °F), and install the ring gear
on the flywheel. Ensure that the chamfer of the gear teeth will be toward the starter pinion
after the flywheel is installed.
1/3(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 1 g00578491
Typical example. Tooling (B) shown is not the tooling called out in the Table.
2. Install Tool (A) in the crankshaft.
3. Fasten Tool (B) to a hoist. Install the tool in the groove of flywheel (2) .
The weight of the flywheel is approximately 78 kg (172 lb).
4. Place flywheel (2) in position on Tools (A) .
Illustration 2 g00578492
Typical example
5. Apply clean engine oil or 5P-0960 Molybdenum Grease to the threads of bolts (2) .
6. Install six of the bolts.
2/3(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 7. Remove Tools (A) and (B) .
8. Install the remainder of bolts (2) . Tighten all of the bolts to a torque of 270 ± 40 N·m (200
± 30 lb ft).
9. Check the runout of the flywheel.
Note: For information on checking for flywheel runout, refer to Testing and Adjusting,
"Flywheel-Inspect".
Note: For more detailed information regarding the flywheel, refer to Specifications, "Flywheel".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 16:38:07 UTC+0800 2021
3/3(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 651E WHEEL SCRAPER 5XR
Configuration: 651E Scraper 5XR00001-UP (MACHINE)
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i07051211
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Ensure that the rear gear remains in place when the crankshaft rear seal and
crankshaft wear sleeve are removed.
1. Install two bolts from the flywheel and suitable washers through the rear gear in the
crankshaft.
1/2(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g01195516
Illustration 2 g00515624
2. Use a punch or Tooling (A) to puncture a hole in seal assembly (1). Use Tooling (A) to
remove seal assembly (1).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 16:39:03 UTC+0800 2021
2/2(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 651E WHEEL SCRAPER 5XR
Configuration: 651E Scraper 5XR00001-UP (MACHINE)
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i01493839
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools for Engines with Rear Gear Train
Tool Part Number Part Description Qty
A
5P-7301 Locator 1
5P-7309 Bolt 2
5P-7310 Bolt 2
8T-2683 Seal Installer 1
9S-8858 Nut 1
Required Tools for Engines without Rear Gear Train
Tool Part Number Part Description Qty
B
5P-1733 Locator 1
5P-1737 Bolt 3
6V-6143 Seal Installer 1
9S-8858 Nut 1
NOTICE
Keep all parts clean from contaminants.
1/5(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Contaminants may cause rapid wear and shortened component life.
Note: Once the seal and the wear sleeve are separated, these components cannot be used again.
Refer to Special Instruction, SMHS8508, "Special Handling Information and Installation
Instructions for Crankshaft Seal Groups that Have Hydrodynamic Grooves In the Sealing Lip"
before the seal is serviced.
Note: Do not use any type of lubricant during the installation of the crankshaft seal and the wear
sleeve.
Note: Before you install the wear sleeve, inspect the crankshaft for scratches or any distortion on
the surface of the crankshaft that may lead to an out of round condition. Use a polishing cloth and
remove any imperfections on the crankshaft.
2/5(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 1 g00477681
1. Install crankshaft rear seal (6) and wear sleeve (1) with Tool (A) or Tool (B), as follows:
3/5(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 2 g00582512
Typical example
a. Use 169-5464 Quick Cure Primer to clean the outside diameter of crankshaft (3) and
the inside diameter of wear sleeve (1).
b. Apply 4C-9507 Retaining Compound to the outside diameter of crankshaft (3). Apply
4C-9507 Retaining Compound to the inside diameter of wear sleeve (1).
c. Put locator (2) in position on crankshaft (3). Install the bolts (7) that hold the locator
in position on the crankshaft.
Illustration 3 g00565570
Typical example
d. Install wear sleeve (1) and seal (6) on crankshaft (3). Put installer (4) on locator (2).
4/5(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 4 g00565576
Typical example
e. Lubricate the face of nut (5). Install nut (5) on locator (4).
f. Tighten nut (5) until installer (4) contacts locator (2).
g. Remove Tool (A) or (B) and check the crankshaft seal and the wear sleeve for the
correct installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 16:39:58 UTC+0800 2021
5/5(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 651E WHEEL SCRAPER 5XR
Configuration: 651E Scraper 5XR00001-UP (MACHINE)
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -SENR1013-11 Publication Date -01/07/2015 Date Updated -22/08/2016
i04977629
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 138-7573 Link Bracket 2
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
B. Remove the crankshaft rear seal and the wear sleeve. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal - Remove".
C. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: There are many possible configurations of the rear gear group and the flywheel housing.
The following procedure illustrates a typical example.
1/14(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 1 g00585225
Typical example
1. Remove exhaust clamp (1) from the right side of the engine.
Illustration 2 g00585471
Typical example
2. Remove exhaust clamp (2) from the left side of the engine.
2/14(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 3 g00585475
Typical example
3. Remove bolts (6), cover (3), bolts (7), cover (4), bolts (8), cover (5), and the gaskets.
Illustration 4 g00585472
Typical example
4. Remove bolts (9) .
3/14(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. Illustration 5 g00585510
Typical example
5. Install Tools (A), and a suitable lifting device to adapter assembly (11) .
6. Use the correct sized forcing screws (10) in order to separate adapter assembly (11) from
the flywheel housing.
The weight of the adapter assembly is approximately 31 kg (68 lb).
Illustration 6 g00585514
Typical example
7. Remove two nuts (14) and the washers.
8. Remove adapter assembly (15) .
4/14(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Illustration 7 g00585525
Typical example
9. Remove O-ring seal (16) from adapter assembly (15), if necessary.
Illustration 8 g00585528
Typical example
10. Remove pin (20), bolts (18), washer (17), and gear (19) from adapter assembly (15), if
necessary.
5/14(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
33. Illustration 9 g00585611
Typical example
11. Remove bolts (21) from adapter assembly (22) .
Illustration 10 g00585651
Typical example
12. Install Tools (A). Attach a suitable lifting device to adapter assembly (22) .
13. Use the correct sized forcing screws (10) in order to remove adapter assembly (22) .
6/14(W)
w
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...