Caterpillar cat 428 f2 backhoe loader (prefix hwn) service repair manual (hwn00001 and up)

Service Repair Manual
Models
428F2 Backhoe Loader

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428F2 BACKHOE LOADER HWN
Configuration: 428F2 Side Shift Backhoe Loader HWN00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i06145783
Transmission (Direct Drive) - Disassemble
SMCS - 3030-015-DD
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 395-1590 Lifting Eye Assembly 2
B 422-5471 Lifting Eye Assembly 1
C 4C-3652 Spring Compressor 1
D 1P-1859 Retaining Ring Pliers 1
E 8H-0663 Bearing Puller Gp 1
F 8B-7551 Bearing Puller Gp 1
G 1U-6400 Three Jaw Puller 1
H 137-8102 Spring Compressor 1
Start By:
a. Remove the transmission.
1/33428F2 Side Shift Backhoe Loader HWN00001-UP (MACHINE) POWERED BY C4.4...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g03827943
1. Use two people to remove torque converter (1). The weight of torque converter (1) is
approximately 23 kg (51 lb). Remove torque converter (1) from transmission (2).
2. Remove bolt (4), the washer, and yoke (3) from transmission (2).
3. Remove shaft (5) from transmission (2).
4. Remove bolts (7) and gear shift (6) from transmission (2).
5. Remove bolts (10) and support assemblies (8) from transmission (2).
6. Remove bolt (11), the washer, and yoke (9) from transmission (2).

7. Remove bolts (13) and solenoid valve (12) from transmission (2).
Personal injury can result from being struck by parts propelled by a
released spring force.

Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove head (14) from solenoid valve (12). Remove O-ring seal (15) from head (14).
9. Remove spring (16), carrier (17), spring (18), and piston (19) from solenoid valve (12).

10. Remove plug (20) from solenoid valve (12). Remove O-ring seal (21) from plug (20).
11. Remove spring (22) and poppet (23) from solenoid valve (12).
12. Remove self locking nut (24), O-ring seal (26) coil assembly (25), and O-ring seal (27) from
solenoid valve (12).

13. Remove tube assembly (28) from solenoid valve (12). Remove O-ring seal (29) from tube
assembly (28).
14. Remove spring (30), push rod (31), washer (32), and spool (33) from solenoid valve (12).
15. Remove O-ring seals (34) from solenoid valve (12).
16. Repeat Step 8 through Step 14 for the opposite side of solenoid valve (12).

17. Attach Tooling (A) and a suitable lifting device to transmission (2). The weight of
transmission (2) is approximately 255 kg (562 lb). Place transmission (2) on a suitable work
bench. Secure transmission (2) to the suitable work bench.
18. Remove bolts (35) that secure the case.
19. Attach Tooling (A) and Tooling (B) to case (36). The weight of case (36) is approximately
45 kg (100 lb). Remove case (36) from the transmission.
Direct Drive, Front Output Shaft

1. Remove front output shaft (37).
2. Use suitable press to remove bearing cone (38).
3. Remove bearing cone (38), thrust washer (39), needle bearing (40), and gear (41) from the
shaft.

4. Remove roller bearing (42), spacer (43), roller bearing (44), needle bearing (45), and thrust
washer (46) from the shaft.
5. Remove retaining ring (47).
6. Remove plate (48).

7. Remove friction disks (49) and friction clutches (50).
8. Use a suitable press and Tooling (C) to compress spring assembly (52). Use Tooling (D) to
remove retaining ring (51).
10/33428F2 Side Shift Backhoe Loader HWN00001-UP (MACHINE) POWERED BY C...

9. Remove spring assembly (52) and retainer (53).
10. Release piston (54) by applying 207 kPa (30 psi) of air pressure into the lube passage as
indicated.
11. Remove seal ring (55).

12. Use Tooling (E) and a suitable press to remove bearing cone (56). Remove bearing cone
(56).
Direct Drive, Rear Output Shaft
1. Remove plug (57), spring (59), and ball (58).

2. Remove screws (60) from the shift forks. Remove rod (61) and ball (62).

Note: Reinstalling plug (57) keeps the spring and the ball from being propelled from the
transmission case.
3. Reinstall plug (57) into the transmission case.
4. Remove rod (63) and shift forks (64).

5. Remove plug (57), ball (67), and spring (66).
6. Remove rear output shaft (65).
7. Remove screw (69) and washer (68).
8. Use Tooling (F) and a suitable press to remove bearing cone (70) and gear (71).

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

9. Remove needle bearings (72) and (73).
10. Use Tooling (D) to remove lock ring (74).
11. Remove synchronizer assembly (75).
12. Remove sleeve (76).

13. Remove gear (77).
14. Remove needle bearings (78) and (79).

15. Use a suitable press to remove bearing cone (80) from the shaft. Remove bearing cone (80),
gear (89), gear (90).
16. Remove shims (81), synchronizer assembly (82), and shims (83).
17. Remove bearing (84), bearing spacer (85), and sleeve (86).
18. Remove sleeve (87), gear (88), bearing spacer (91), and bearing (92).
Direct Drive Shaft
1. Remove direct drive shaft (93).

Caterpillar cat 428 f2 backhoe loader (prefix hwn) service repair manual (hwn00001 and up)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat 428 f2 backhoe loader (prefix hwn) service repair manual (hwn00001 and up)

Similar to Caterpillar cat 428 f2 backhoe loader (prefix hwn) service repair manual (hwn00001 and up) (10)

More from jfjkskekfsmem

More from jfjkskekfsmem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 428 f2 backhoe loader (prefix hwn) service repair manual (hwn00001 and up)