Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn00001 03615)

Service Repair Manual
Models
426C Backhoe Loader

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 6XN
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 6XN00001-03615 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01543773
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
B 9U-6282 Torque Wrench Extension 1
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
B. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
Note: The engine oil pump is mounted on the No. 1 crankshaft main bearing cap. The engine oil
pump can be removed without removing the front housing if the No. 1 crankshaft main bearing
cap is removed. Use Tool (B) in order to remove the No. 1 crankshaft main bearing cap. The
engine oil pump is then removed from the No. 1 crankshaft main bearing cap.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3426C Backhoe Loader Center Pivot, Single Tilt 6XN00001-03615 (MACHINE) POW...
2019/12/7https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00552238
1. Remove two bolts (1) that fasten the strainer and suction pipe to the engine oil pump.
2. Remove bolt (2) that holds the strainer in position.
3. Remove the strainer, suction pipe (3), and the gasket from the engine.
4. Remove the engine oil relief valve. Refer to the Disassembly and Assembly Module,
"Engine Oil Relief Valve - Remove".

5. Use Tool (A) to remove retaining ring (4) from the idler gear shaft.
6. Remove idler gear (5) from the idler gear shaft. Inspect the idler gear shaft for wear or
damage. If the idler gear shaft is worn or damaged, use a new part for replacement. Use a
suitable press to remove the idler gear shaft from the No. 1 main bearing cap.
7. Remove three bolts (6) from the No. 1 main bearing cap.
8. Remove engine oil pump (7) from the engine.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 7 22:48:31 UTC+0800 2019

Shutdown SIS
Previous Screen
i01052799
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
A 1P-1855 Retaining Ring Pliers 1
NOTICE
NOTICE
If any of the parts on the engine oil pump are worn or damaged, the
entire pump must be replaced.
Note: If the No. 1 crankshaft main bearing cap was removed, install the No. 1 crankshaft main
bearing cap with the engine oil pump. Tighten the bolts for the No. 1 crankshaft main bearing cap
to a torque of 265 N·m (195 lb ft).

1. If the shaft for the idler gear on the engine oil pump was removed, remove the excess
Loctite 603. Apply a new layer of Loctite 603 to the bore in the main bearing cap and install
the shaft.
2. Fill engine oil pump (7) with clean engine oil. Install engine oil pump (7) on the engine.
3. Install three bolts (6). Tighten the bolts to a torque of 22 N·m (16 lb ft).
4. Install idler gear (5) .
5. Use Tool (A) to install retaining ring (4) .
Note: After you install the engine oil pump and the idler gear, ensure that there is a
minimum of 0.08 mm (.003 inch) backlash between the gear on the engine oil pump and the
idler gear.
6. Install the engine oil relief valve. Refer to Disassembly and Assembly, "Engine Oil Relief
Valve - Install".

7. Install the strainer, suction pipe (3), and the gasket.
8. Install bolt (2). Tighten the bolt to a torque of 22 N·m (16 lb ft).
9. Install two bolts (1). Tighten the bolts to a torque of 22 N·m (16 lb ft).
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Sat Dec 7 22:49:26 UTC+0800 2019

Shutdown SIS
Previous Screen
i01644325
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
NOTICE
NOTICE
containing fluids.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.

Typical example
2. Remove eight bolts (1) and two nuts (2) that fasten the water pump to the front housing.
3. Tap water pump (3) with a soft hammer in order to loosen water pump (3) .
4. Remove water pump (3) and the gasket.
Sat Dec 7 22:50:22 UTC+0800 2019

Shutdown SIS
Previous Screen
i01081184
Water Pump - Disassemble - Type 1 Engines and 9RM
Engines
SMCS - 1361-015
Disassembly Procedure
Table 1
Required Tools
A
6V-3009 Crossbar 1
5H-9976 Screw 1
9S-9152 Bearing Pul 1
7X-0290 Bolt 2
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
Note: For a complete description of Type 1 and Type 2 engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE

NOTICE
containing fluids.
1. Remove six bolts (1). Remove cover (2) and the gasket.

2. Remove O-ring seal (3) .
3. Install Tool (A). Remove gear (4) .
4. Use a suitable lever in order to remove seal (5) .

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

5. Use a suitable press in order to remove shaft (6), seal (7), and impeller (8) from housing
(9) .
Note: The water pump for Type 2 Engines and 7BJ Engines is not serviceable. Contact your
Caterpillar dealer for more replacement information.
Sat Dec 7 22:51:18 UTC+0800 2019

Shutdown SIS
Previous Screen
i01082733
Water Pump - Assemble - Type 1 Engines and 9RM Engines
SMCS - 1361-016
Assembly Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Note: The water pump for Type 2 Engines and 7BJ Engines is not serviceable. Contact your
Caterpillar dealer for more replacement information.
1. Clean the inside of the pump body. Ensure that the bearing bore and the counterbore for the
water seal are particularly clean.
2. Apply 4C-9507 Retaining Compound to the outer surface of the bearing. Keep the
compound away from the ends of the bearing.

3. Support the gear end of the water pump body.
4. Place the bearing and shaft (6) square in the pump body. Ensure that the shortest end of
shaft (6) is in housing (9) .
5. Use a suitable press and a suitable adapter that will apply force to the bearing. The adapter
should not apply force to the shaft. Press the bearing onto the shaft until the end of the
bearing is level with the bottom of the counterbore for the water seal.
Note: Remove the excess compound from the end of the bearing.
6. Install seal (7) .
NOTICE
Ensure that the water seal is not contaminated by oil or grease. Hold
the seal only by the edge of the flange. Do not damage the ring of green
sealant that is applied to the body of the water seal behind the flange.

7. Hold water seal (5) by the edge of the flange. Push the seal onto shaft (6) until the seal is
against the chamfer of the counterbore. Only apply force to the outer flange of the seal.
Note: Ensure that the wide end of the seal is toward the bearing and that the seal is square
with the counterbore.
8. Continue to apply force and hold water seal (5) for ten seconds. This ensures that the water
seal will remain in place.
9. Hold the water pump with the gear end of the shaft on a suitable support. Use a flat bar in
order to press impeller (8) onto shaft (6) to a depth of 8.30 ± 0.20 mm (.320 ± .010 inch).
After installation, ensure that the impeller will turn freely.
Note: Apply 4C-9507 Retaining Compound to impeller (8) if the original impeller is used.
Remove excess compound after assembly.
10. Lubricate oil seal (3) with clean engine oil. Install oil seal (3) with the flat surface toward
the bearing. Press oil seal (3) into the body with a suitable adapter until the rear of the seal is
level with the end of the pump.
11. Continue to apply force and hold oil seal (3) in position for ten seconds. This ensures that
the seal will remain in place.
12. Press gear (4) onto shaft (6) to a depth of 1.60 ± 1.00 mm (.015 ± .005 inch) .
Note: Apply 4C-9507 Retaining Compound to gear (4) if the original gear is used. Remove
excess compound after assembly.

Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn00001 03615)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn00001 03615)

Similar to Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn00001 03615) (14)

More from fusjejfjskekemm

More from fusjejfjskekemm (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn00001 03615)