This document provides instructions for removing and installing camshaft bearings, engine oil pans, piston cooling jets, pistons, and connecting rods on a 3054C engine. It outlines the required tools and parts, removal and installation procedures with illustrations, and safety notices to keep parts clean and contain fluids. The summary focuses on the high-level steps and does not include part numbers or other specific details.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 424D BACKHOE LOADER RXA
Configuration: 424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02299758
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00546333
Illustration 2 g00546238
1. Use the Tooling (A) in order to remove the camshaft bearing (1) from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00546238
Illustration 4 g00546333
1. Use the Tooling (A) in order to install the camshaft bearing (1) into the bore in the cylinder
block.
Note: Align the oil hole in camshaft bearing (1) with the oil hole in the bore in the cylinder
block.
Note: The camshaft bearing must be inserted until the front edge of the bearing is flush with
the face of the recess in the cylinder block.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 6 16:34:10 UTC+0800 2019
3/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 424D BACKHOE LOADER RXA
Configuration: 424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i05003149
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00956531
1. Remove all dirt, oil, and grease from the exterior surfaces of the oil pan (5).
2. Operate the engine until the engine is warm. Stop the engine.
3. Remove the oil drain plug (6) and the O-ring seal. Drain the engine oil into a suitable
container for storage or disposal.
Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for information
on the capacity of the lubrication system.
Note: Ensure that the engine oil pan is fully supported before the oil pan is removed.
Particular care must be taken with the cast iron version of the engine oil sump as this
version is heavy.
4. Remove the setscrews (3) and the setscrews (4) from the engine oil pan (5).
5. Remove the engine oil pan (5) and remove the gasket (1) from the cylinder block. Discard
the gasket (1).
6. If necessary, remove the nut (2), the seal, and the tube assembly from the engine oil pan.
7. Clean the engine oil pan (5) with a suitable cleaning fluid. Ensure that all of the cleaning
fluid is removed.
Installation Procedure
2/5
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(M8 x 1.25 x 70 mm)
4
B - Loctite 5900 -
C - Loctite 243 -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the flange face of the engine oil pan (5) and the flange face of the cylinder block.
Illustration 2 g00541498
2. When the gasket for the oil pan is removed, damage may occur to the existing seal in the
groove of the bridge. If the seal is damaged, apply a sufficient amount of Tooling (B) in
order to fill the groove. The groove must be completely filled.
3. Apply Tooling (B) to the joint between the cylinder block and the front housing.
3/5
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00956479
4. Install Tooling (A) in the cylinder block in Hole (X).
Note: New setscrews have sealant on the first 13 mm (0.5 inch) of the threads. In order to
reuse the old setscrews, clean the old sealant from the bolts and apply Tooling (C) to the
setscrews.
Note: Ensure that the engine oil pan is properly supported while the engine oil pan (5) is
installed onto the cylinder block.
5. Position a new gasket (1) and the engine oil pan (5) on the cylinder block. Install the
setscrews (3 and 4) in order to secure the engine oil pan to the cylinder block. Tighten the
setscrews finger tight.
6. Remove the Tooling (A) and install the remaining setscrews (3 an 4). Tighten the setscrews
(3) in Hole (Y) to a torque of 22 N·m (16 lb ft).
7. Tighten the remaining setscrews (3 and 4) to a torque of 22 N·m (16 lb ft).
8. Inspect the O-ring for the drain plug (6). Replace the O-ring if it is necessary. Install the O-
ring seal and drain plug (6). Tighten the drain plug to a torque of 34 N·m (25 lb ft).
9. If necessary, install the seal and the tube assembly in the engine oil pan. Tighten the nut (2)
to a torque of 18 N·m (13 lb ft).
10. Fill the engine oil pan to the correct level that is indicated on the engine oil level gauge.
4/5
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for the
lubrication system capacity of the engine.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 6 16:35:06 UTC+0800 2019
5/5
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 424D BACKHOE LOADER RXA
Configuration: 424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02300831
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01152129
1. Remove the setscrew (1). Remove the piston cooling jet assembly (2) from the cylinder
block.
Note: The engine crankshaft may be rotated in order to access all of the piston cooling jet
assemblies.
Note: Ensure that the ball moves freely within the valve assembly of the piston cooling jet.
Check that the tube of the piston cooling jet assembly is not damaged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g01152132
1. Install piston cooling jet assembly (2) to the cylinder block. Install the setscrew (1). Tighten
the setscrew (1) to a torque of 9 N·m (80 lb in).
Note: Ensure that piston cooling jet assembly (2) is properly located on the cylinder block.
Refer to the Specifications Manual, "Piston Cooling Jet" for the correct procedure for the
alignment of the piston cooling jet.
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 6 16:36:02 UTC+0800 2019
3/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 424D BACKHOE LOADER RXA
Configuration: 424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02301207
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2269 Ridge Reamer 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
b. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
c. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
d. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 1. Use Tooling (A) in order to remove the carbon ridge from the top inside surface of the
cylinder liners.
2. Rotate the crankshaft until the pistons that are being removed are at the bottom center
position.
Illustration 1 g00970465
3. Remove the setscrews (1).
Note: Do not reuse the setscrews (1). Use new setscrews in order to secure the connecting
rod cap for reassembly.
4. Remove the connecting rod cap (2) and the connecting rod bearing.
Note: Inspect the connecting rod and connecting rod cap for the proper identification mark.
The connecting rod and the connecting rod cap should have an etched number on the side.
The number should match the cylinder number. Mark the connecting rod and the connecting
rod cap, if necessary.
Note: Do not stamp the connecting rod assembly. Stamping or punching the connecting rod
assembly could cause the connecting rod to fracture.
5. Put a temporary identification mark on the top of the piston in order to indicate the cylinder
number that is shown on the connecting rod. Put the temporary mark on the same side as the
mark that is on the connecting rods in order to ensure correct assembly of the piston and the
connecting rod.
Note: Do not etch the top surface of the piston. Do not allow scratches or stamped markings
in the top surface of the piston.
6. Push the pistons and the connecting rods through the top of the cylinder block.
7. Repeat Steps 2 through 6 in order to remove the remaining pistons and connecting rods.
2/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 424D BACKHOE LOADER RXA
Configuration: 424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i01880507
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1857 Retaining Ring Pliers 1
C 1P-0510 Driver Group 1
Start By:
a. Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston
and Connecting Rods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00970499
1. Remove the lower connecting rod bearing from the connecting rod cap. Remove the upper
connecting rod bearing from the connecting rod.
Note: The forged marks (X) must be installed toward the front of the engine.
Illustration 2 g00964585
2. Use Tooling (A) in order to remove compression rings (1) and (2), and oil control ring (3)
from piston (6).
3. Use Tooling (B) in order to remove retaining rings (8) that hold the piston pin in position.
4. Remove piston pin (7) from the piston.
2/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Note: If the piston pin cannot be removed by hand, heat the piston to a temperature of
45 ± 5 °C (113 ± 9 °F). Do not use a torch to heat the piston.
5. Use Tooling (C) and a suitable press in order to remove bushing (4) from connecting rod
(5).
6. Repeat Steps 1 through 5 in order to disassemble the remaining pistons and connecting rods.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 6 16:37:54 UTC+0800 2019
3/3
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 424D BACKHOE LOADER RXA
Configuration: 424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i07489015
Pistons and Connecting Rods - Assemble
SMCS - 1225-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Installation of the piston pin bushing must be carried out by personnel
with the correct training. Also special machinery is required.
Note: A new piston pin bushing is in a shape of a wedge. For further information on installation of
the piston pin bushing, refer to your authorized Caterpillar dealer or your Caterpillar distributor
for assistance.
1/4
424D Backhoe Loader RXA00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2019/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...