This document provides disassembly and assembly instructions for the travel motor of a 390F L excavator. It outlines 40 steps to disassemble the travel motor by removing components like the head, relief valves, port plate, piston, and shaft. It then outlines 12 steps for reassembling the travel motor, starting with installing seals and bearings and finishing by reinstalling the piston and head. Precautions are provided around spring loaded components.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 390F L EXCAVATOR MGF
Configuration: 390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine
Disassembly and Assembly
390F Excavator Machine Systems
Media Number -UENR0165-05 Publication Date -01/01/2018 Date Updated -24/01/2018
i05680270
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0074 Slide Hammer Puller Gp 1
C 123-4370 Threaded Rod M20 - 2.5 2
D 1P-1864 Pliers 1
E 1P-1858 Pliers 1
F 1P-0520 Driver Group 1
G 8T-0349 Bolt 2
Start By:
a. Remove the travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
1. Place an alignment mark across all housings of the travel motor for assembly purposes.
Illustration 1 g01282832
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. Remove two socket head bolts (2) from head (1) that are 180 degrees from each other.
Replace these two bolts with Tooling (G). Tooling (G) will retain the brake cover when the
remaining socket head bolts (2) are removed.
3. Carefully remove the remaining socket head bolts (2) that retain head (1) in position.
Remove socket head bolts (2) evenly, in a crisscross pattern.
4. Remove Tooling (G) from head (1).
2/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g01283040
5. Install Tooling (A) and a suitable lifting device to head (1).
6. Remove head (1) from the travel motor. The weight of head (1) is approximately 68 kg
(150 lb).
Illustration 3 g01283045
7. Remove relief valve (3).
Illustration 4 g01283049
3/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove cap (4) from body (9). Remove piston (5), spring (6), spool (7), and spring (8) from
body (9).
9. Remove O-ring seals (10), (12), and (14). Remove backup rings (11) and (13).
10. Remove the other relief valve from the other side of the head.
11. Repeat Steps 8 and 9 for the disassembly of the other relief valve.
Illustration 5 g01283057
12. Remove plug (15).
Illustration 6 g01283060
4/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 13. Remove spool (16).
Illustration 7 g01283070
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
14. Remove plug (17).
Illustration 8 g01283075
15. Remove spool (21) from the head. Remove O-ring seal (22) from plug (17).
16. Remove plug (18) from the other side of the head. Remove spring (20). Remove O-ring seal
(19) from plug (18).
5/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 9 g01283083
17. Remove cap (23) and pressure reducing valve (24).
Illustration 10 g01283088
18. Remove O-ring seals (25), (26), and (27) from pressure reducing valve (24).
Illustration 11 g01283096
19. Use Tooling (B) in order to remove bearing (28) from the head.
6/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 12 g01283101
20. Remove port plate (29) from the travel motor.
Note: Note the location of springs (30) before removal.
21. Remove springs (30) from the travel motor.
22. Remove O-ring seals (31).
Illustration 13 g01283110
23. Place alignment marks on piston (32) and the housing. The dowel hole in piston (32) must
be reinstalled to the original location.
7/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 14 g01283120
24. Install Tooling (C) to the threaded holes in piston (32). Install Tooling (A) and a suitable
lifting device on Tooling (C), as shown. Remove piston (32) from the travel motor.
Illustration 15 g01283129
25. Remove O-ring seals (33) and (34) from the travel motor.
Illustration 16 g01283133
26. Remove separator plates (35) and friction plates (36) from the travel motor.
Illustration 17 g01283138
8/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 18 g01283139
Note: Barrel assembly (37), piston assemblies (39), and retainer (40) must remain intact
during removal.
27. Position the travel motor sideways. Carefully remove barrel assembly (37) from shaft (38).
Illustration 19 g01283155
28. Place identification marks on piston assemblies (39), retainer (40), and barrel assembly (37).
These components must be reinstalled in the original location.
29. Remove retainer (40) and piston assemblies (39) from barrel assembly (37).
9/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 20 g01283175
Illustration 21 g01283193
30. Remove guide (41).
31. Remove springs (42).
Illustration 22 g01283187
32. Turn swashplate (43) counterclockwise in order to provide clearance for the removal of
swashplate (43).
33. Remove swashplate (43) from the travel motor housing.
10/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 23 g01283195
34. Remove piston (44) and pivots (45).
Illustration 24 g01283206
35. Use Tooling (D) in order to remove retaining ring (46) from shaft (38).
Illustration 25 g01283209
36. Use a soft hammer in order to drive shaft (38) and bearing (47) from the motor housing.
11/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 26 g01283212
37. Use Tooling (E) in order to remove retaining ring (48) from bearing (47).
Illustration 27 g01283232
38. Use a suitable press in order to remove bearing (47) from shaft (38).
Illustration 28 g01283244
39. Remove retaining ring (49) and bearing race (50).
12/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 29 g01283253
40. Use Tooling (F) in order to remove lip seal (51) from the travel motor housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 09:22:23 UTC+0800 2020
13/13
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 390F L EXCAVATOR MGF
Configuration: 390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine
Disassembly and Assembly
390F Excavator Machine Systems
Media Number -UENR0165-05 Publication Date -01/01/2018 Date Updated -24/01/2018
i02563228
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
D 1P-1864 Pliers 1
E 1P-1858 Pliers 1
F 1P-0520 Driver Group 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Apply a light film of 10W oil to all components before assembly.
1/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01283253
1. Use Tooling (F) in order to install lip seal (51) in the travel motor housing.
Illustration 2 g01283244
2. Install bearing (50) and retaining ring (49).
Illustration 3 g01283329
3. Raise the temperature of bearing (47). Install bearing (47) onto shaft (38).
2/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g01283212
4. Use Tooling (E) in order to install retaining ring (48) onto bearing (47).
Illustration 5 g01283209
5. Install shaft (38) and bearing (47) into the motor housing.
Illustration 6 g01283206
6. Use Tooling (D) in order to install retaining ring (46) onto shaft (38).
3/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 10 g01283175
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
9. Install springs (42).
10. Install guide (41).
Illustration 11 g01283155
11. Install retainer (40) and piston assemblies (39) into barrel assembly (37). These components
must be reinstalled in the original location.
5/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 12 g01283139
Note: Barrel assembly (37), piston assemblies (39), and retainer (40) must remain intact
during installation onto shaft (38).
12. Position the travel motor sideways.
Illustration 13 g01283138
13. Carefully install barrel assembly (37) onto shaft (38).
Illustration 14 g01283133
14. Install separator plates (35) and friction plates (36) into the travel motor.
6/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 15 g01283129
15. Install O-ring seals (33) and (34) into the travel motor.
Illustration 16 g01283110
Note: Piston (32) must be reinstalled in the original location.
16. Install piston (32).
Illustration 17 g01283350
7/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Note the location of springs (30) for installation.
17. Install springs (30) and O-ring seals (31) to the travel motor.
Illustration 18 g01283096
18. Lower the temperature of bearing (28). Install bearing (28) in the head.
Illustration 19 g01283088
19. Install O-ring seals (25), (26), and (27) on pressure reducing valve (24).
8/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 20 g01283083
20. Install pressure reducing valve (24). Tighten pressure reducing valve (24) to a torque of
44 ± 4 N·m (33 ± 3 lb ft).
21. Install cap (23).
Illustration 21 g01283075
22. Install O-ring seal (22) onto plug (17). Install spool (21) and plug (17) to the head.
23. Install O-ring seal (19) onto plug (18). Install spring (20) and plug (18) to the head.
24. Tighten plugs (17) and (18) to a torque of 74 ± 7 N·m (55 ± 5 lb ft).
9/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP65...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 22 g01283060
25. Install spool (16).
Illustration 23 g01283057
26. Install plug (15).
Illustration 24 g01283049
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install O-ring seals (10), (12), and (14) and backup rings (11) and (13).
28. Install piston (5), spring (6), spool (7), and spring (8) in body (9). Install cap (4) in body (9).
29. Repeat Steps 27 and 28 for the assembly of the other relief valve.
10/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 25 g01283045
30. Install relief valves (3). Tighten relief valves (3) to a torque of 177 ± 18 N·m
(131 ± 13 lb ft).
Illustration 26 g01283396
31. Use light grease to install port plate (29) on the head.
11/12
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine(SEBP...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...