The document provides instructions to disassemble a travel motor over 27 steps. It begins by removing the travel motor and draining fluids. Various components are then removed from the motor housing, head assembly, and barrel assembly including seals, plates, springs, pistons, and bearings. Tools required include link brackets, eyebolts, pullers, threaded rods, bolts and nuts to detach components in a specific order. Personal protective equipment is recommended when removing parts under spring pressure.
Caterpillar Cat 349F and 349F L Excavator (Prefix BZ2) Service Repair Manual ...shibi1322
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It lists 27 steps to remove components like plugs, seals, springs, pistons, plates, and housing pieces. Tools required include lifting devices, bolts, nuts, and specialty pullers and presses. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy.
Caterpillar Cat 349F and 349F L Excavator (Prefix BZ2) Service Repair Manual ...f89siekkmdmm2w
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, plates, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers. Safety precautions are noted to avoid injury from released spring forces during disassembly.
Caterpillar Cat 349F and 349F L Excavator (Prefix BZ2) Service Repair Manual ...f8uejkdkdmm3e
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, plates, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers. Safety precautions are noted to avoid injury from released spring forces when removing certain parts.
Caterpillar cat 349 f l excavator (prefix bz2) service repair manual (bz20000...didkskdkmdm
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, plates, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers. Safety precautions are noted to avoid injury from released spring forces when removing certain parts.
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, plates, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers. Safety precautions are noted to avoid injury from released spring forces during disassembly.
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It details 27 steps to remove components like the motor head assembly, various plugs and seals, springs, valves, and more. Tools required include lifting devices, bolts, nuts, and pullers. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy.
Caterpillar Cat 349F L Excavator (Prefix BZ2) Service Repair Manual (BZ200001...fujsekmd9idd
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housing pieces. Safety precautions are included to warn of potential injury from released spring forces. Required tools include lifting devices, bolts, nuts, and specialized pullers and presses.
Caterpillar Cat 349F L Excavator (Prefix BZ2) Service Repair Manual (BZ200001...fuusejkddmmd3e
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, valves, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers to detach parts. Safety precautions are noted to avoid injury from released spring forces during disassembly.
Caterpillar Cat 349F and 349F L Excavator (Prefix BZ2) Service Repair Manual ...shibi1322
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It lists 27 steps to remove components like plugs, seals, springs, pistons, plates, and housing pieces. Tools required include lifting devices, bolts, nuts, and specialty pullers and presses. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy.
Caterpillar Cat 349F and 349F L Excavator (Prefix BZ2) Service Repair Manual ...f89siekkmdmm2w
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, plates, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers. Safety precautions are noted to avoid injury from released spring forces during disassembly.
Caterpillar Cat 349F and 349F L Excavator (Prefix BZ2) Service Repair Manual ...f8uejkdkdmm3e
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, plates, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers. Safety precautions are noted to avoid injury from released spring forces when removing certain parts.
Caterpillar cat 349 f l excavator (prefix bz2) service repair manual (bz20000...didkskdkmdm
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, plates, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers. Safety precautions are noted to avoid injury from released spring forces when removing certain parts.
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, plates, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers. Safety precautions are noted to avoid injury from released spring forces during disassembly.
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It details 27 steps to remove components like the motor head assembly, various plugs and seals, springs, valves, and more. Tools required include lifting devices, bolts, nuts, and pullers. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy.
Caterpillar Cat 349F L Excavator (Prefix BZ2) Service Repair Manual (BZ200001...fujsekmd9idd
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housing pieces. Safety precautions are included to warn of potential injury from released spring forces. Required tools include lifting devices, bolts, nuts, and specialized pullers and presses.
Caterpillar Cat 349F L Excavator (Prefix BZ2) Service Repair Manual (BZ200001...fuusejkddmmd3e
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, valves, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers to detach parts. Safety precautions are noted to avoid injury from released spring forces during disassembly.
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...fujkse9didkke3
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations accompany each step to show how to disassemble and reassemble the components.
3. Special attention is drawn to cleaning parts and applying threadlocker during installation to prevent contamination and ensure proper component life.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
Caterpillar Cat 330D L Excavator (Prefix NBD) Service Repair Manual (NBD00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...fujkse9didkke3
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fujkse9didkke3
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...fujkse9didkke3
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, housings and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have assistance when removing heavier components weighing over 30 kg.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...fujkse9didkke3
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fujkse9didkke3
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the fully assembled piston motor and fan assembly onto mounting brackets on the excavator.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
This document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing over 30 individual parts in a specific sequence, including gears, shafts, bearings, seals, and housing components. Special tools are required to remove some parts. Proper lifting equipment and safety precautions are needed due to the heavy weights involved, up to approximately 550 kg for the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It outlines 28 steps for disassembly, removing components like the head, brake piston, plates and discs. It then outlines 13 steps for assembly, including installing seals, bearings, springs and ensuring proper placement of parts. Cleanliness is emphasized throughout the process.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
Caterpillar Cat 330C L Excavator (Prefix JAB) Service Repair Manual (JAB00001...fujkse9didkke3
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
3) It then describes 29 steps for assembling the travel motor, providing notes on cleaning, lubrication, and proper installation of components like O-rings, pistons, seals, and bolts.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models. It outlines 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then lists 13 steps for reassembling the motor and installing components in the reverse order of disassembly while ensuring cleanliness and applying thread lock compounds as needed.
How to Prepare for Fortinet FCP_FAC_AD-6.5 Certification?NWEXAM
Begin Your Preparation Here: https://bit.ly/3VfYStG — Access comprehensive details on the FCP_FAC_AD-6.5 exam guide and excel in the Fortinet Certified Professional - Network Security certification. Gather all essential information including tutorials, practice tests, books, study materials, exam questions, and the syllabus. Solidify your knowledge of Fortinet FCP_FAC_AD-6.5 certification. Discover everything about the FCP_FAC_AD-6.5 exam, including the number of questions, passing percentage, and the time allotted to complete the test.
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...fujkse9didkke3
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations accompany each step to show how to disassemble and reassemble the components.
3. Special attention is drawn to cleaning parts and applying threadlocker during installation to prevent contamination and ensure proper component life.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
Caterpillar Cat 330D L Excavator (Prefix NBD) Service Repair Manual (NBD00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...fujkse9didkke3
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fujkse9didkke3
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...fujkse9didkke3
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, housings and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have assistance when removing heavier components weighing over 30 kg.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...fujkse9didkke3
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fujkse9didkke3
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the fully assembled piston motor and fan assembly onto mounting brackets on the excavator.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
This document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing over 30 individual parts in a specific sequence, including gears, shafts, bearings, seals, and housing components. Special tools are required to remove some parts. Proper lifting equipment and safety precautions are needed due to the heavy weights involved, up to approximately 550 kg for the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It outlines 28 steps for disassembly, removing components like the head, brake piston, plates and discs. It then outlines 13 steps for assembly, including installing seals, bearings, springs and ensuring proper placement of parts. Cleanliness is emphasized throughout the process.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
Caterpillar Cat 330C L Excavator (Prefix JAB) Service Repair Manual (JAB00001...fujkse9didkke3
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
3) It then describes 29 steps for assembling the travel motor, providing notes on cleaning, lubrication, and proper installation of components like O-rings, pistons, seals, and bolts.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models. It outlines 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then lists 13 steps for reassembling the motor and installing components in the reverse order of disassembly while ensuring cleanliness and applying thread lock compounds as needed.
How to Prepare for Fortinet FCP_FAC_AD-6.5 Certification?NWEXAM
Begin Your Preparation Here: https://bit.ly/3VfYStG — Access comprehensive details on the FCP_FAC_AD-6.5 exam guide and excel in the Fortinet Certified Professional - Network Security certification. Gather all essential information including tutorials, practice tests, books, study materials, exam questions, and the syllabus. Solidify your knowledge of Fortinet FCP_FAC_AD-6.5 certification. Discover everything about the FCP_FAC_AD-6.5 exam, including the number of questions, passing percentage, and the time allotted to complete the test.
5 Common Mistakes to Avoid During the Job Application Process.pdfAlliance Jobs
The journey toward landing your dream job can be both exhilarating and nerve-wracking. As you navigate through the intricate web of job applications, interviews, and follow-ups, it’s crucial to steer clear of common pitfalls that could hinder your chances. Let’s delve into some of the most frequent mistakes applicants make during the job application process and explore how you can sidestep them. Plus, we’ll highlight how Alliance Job Search can enhance your local job hunt.
Leadership Ambassador club Adventist modulekakomaeric00
Aims to equip people who aspire to become leaders with good qualities,and with Christian values and morals as per Biblical teachings.The you who aspire to be leaders should first read and understand what the ambassador module for leadership says about leadership and marry that to what the bible says.Christians sh
Learnings from Successful Jobs SearchersBruce Bennett
Are you interested to know what actions help in a job search? This webinar is the summary of several individuals who discussed their job search journey for others to follow. You will learn there are common actions that helped them succeed in their quest for gainful employment.
Job Finding Apps Everything You Need to Know in 2024SnapJob
SnapJob is revolutionizing the way people connect with work opportunities and find talented professionals for their projects. Find your dream job with ease using the best job finding apps. Discover top-rated apps that connect you with employers, provide personalized job recommendations, and streamline the application process. Explore features, ratings, and reviews to find the app that suits your needs and helps you land your next opportunity.
Jill Pizzola's Tenure as Senior Talent Acquisition Partner at THOMSON REUTERS...dsnow9802
Jill Pizzola's tenure as Senior Talent Acquisition Partner at THOMSON REUTERS in Marlton, New Jersey, from 2018 to 2023, was marked by innovation and excellence.
A Guide to a Winning Interview June 2024Bruce Bennett
This webinar is an in-depth review of the interview process. Preparation is a key element to acing an interview. Learn the best approaches from the initial phone screen to the face-to-face meeting with the hiring manager. You will hear great answers to several standard questions, including the dreaded “Tell Me About Yourself”.
IT Career Hacks Navigate the Tech Jungle with a RoadmapBase Camp
Feeling overwhelmed by IT options? This presentation unlocks your personalized roadmap! Learn key skills, explore career paths & build your IT dream job strategy. Visit now & navigate the tech world with confidence! Visit https://www.basecamp.com.sg for more details.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349F L EXCAVATOR HPD
Configuration: 349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349F and 352F Excavators Machine Systems
Media Number -UENR0194-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i04243909
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B - Bolt M4 x 0.7 1
C 6V-3010 Puller Gp 1
D 3E-3879 Eyebolt 1
E 9S-9152 Bearing Puller Gp 1
Start By:
a. Remove the travel motor.
1. Drain the travel motor.
1/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02419258
2. Remove O-ring seal (1) from motor housing (2).
Illustration 2 g02419296
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Attach Tooling (A) onto head assembly (3). Remove bolts (4). Use Tooling (A) and a
suitable lifting device to remove head (3). The weight of head assembly (3) is
approximately 40 kg (90 lb).
2/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g02419358
4. Remove plate (5) from head (3).
Illustration 4 g02419359
5. Remove bearing (6) from head assembly (3).
6. Remove orifice (7), spring (8), and ball (9).
7. Remove O-ring seal (10) from head assembly (3).
Illustration 5 g02419416
3/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove adapter (11), spool (12), and spring (13) from head assembly (3).
Illustration 6 g02419439
9. Use Tooling (B) in order to remove retainers (14) from head assembly (3).
10. Remove O-ring seals (16) and backup rings (15) from adapters (14).
11. Remove balls (17) from head assembly (3).
Illustration 7 g02419577
12. Remove springs (18) from brake housing (20).
4/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 13. Remove O-ring seals (19) from motor housing (2).
Illustration 8 g02420880
14. Use Tooling (C) in order to remove brake housing (20) from motor housing (2).
Illustration 9 g02419659
15. Remove backup ring (21) and O-ring seal (22) from brake piston (20).
16. Remove O-ring seal (23) and backup ring (24) from brake piston (20).
5/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g02419858
17. Attach Tooling (D) to shaft assembly (25).
18. Use Tooling (D) and a suitable lifting device in order to lift the rotating group from motor
housing (2). The weight of the rotating group is approximately 30 kg (65 lb).
Illustration 11 g02420501
19. Remove plates (26) and friction disks (27) from barrel assembly (28).
6/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g02420544
20. Remove barrel assembly (28) and swashplate (29) from shaft assembly (25).
Illustration 13 g02420578
21. Remove plate (31) and pistons (30) from barrel assembly (28).
7/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g02420596
22. Remove bearing (32), thin shim (33), Belleville washers (34), and barrel spacer (35) from
barrel assembly (28).
Illustration 15 g02420937
23. Use a suitable press in order to remove bearing (36) from shaft assembly (25).
8/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 16 g02421036
24. Use Tooling (E) and a suitable press in order to remove inner race (37) from shaft assembly
(25).
Illustration 17 g02420998
Illustration 18 g02421000
9/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 25. Remove keys (38) and pins (39) from motor housing (2).
Illustration 19 g02421056
26. Remove plug (40) and the O-ring seal. Remove actuator piston (41).
27. Remove retaining ring (42) and seal (43) from motor housing (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 23 20:12:25 UTC+0800 2020
10/10
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349F L EXCAVATOR HPD
Configuration: 349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349F and 352F Excavators Machine Systems
Media Number -UENR0194-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07203491
Travel Motor - Disassemble
SMCS - 4351-015
Disassemble Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
154-6182 M12x1.75 mm Forcing Bolt 2
6V-8149 M12x1.75 mm Nut 4
5P-8245 M12 Hard Washer 4
D
- M3x0.5 Threaded Rod 1
3K-3068 3 mm Thrust Washer 1
3C-6969 M3x0.5 Nut 2
E
8T-0276 M8x45mm Bolt 2
9M-1974 M8 Hard Washer 2
Start By:
a. Remove travel motor.
NOTICE
1/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06252257
1. Use Tooling (B) and a suitable lifting device to position travel motor (1) in a vertical
position on Tooling (A). The weight of travel motor (1) is approximately 136 kg (300 lb).
Use Tooling (C) to attach travel motor (1) to Tooling (A).
Illustration 2 g06252275
2. Remove plugs (2), plug (3), plug (4), and the O-ring seals.
2/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 3 g06252280
Illustration 4 g06252989
3. Remove plug (6) and the O-ring seal.
4. Remove plug (5), stopper (7), and ball (8).
3/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g06255756
Illustration 6 g06255791
5. Use Tooling (D) and a suitable washer to extract seat (8A).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 7 g06252992
Illustration 8 g06252996
6. Remove plugs (9) and the O-ring seals.
7. Remove plug (10), spool (11), spring (12), and the O-ring seal.
Illustration 9 g06253028
8. Remove plug (13), valve (14) , and the O-ring seals.
5/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 10 g06253047
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove the top two nuts and washers from Tooling (C).
10. Remove bolts (15).
11. Use Tooling (B) and a suitable lifting device to remove motor head assembly (16). The
weight of motor head assembly (16) is approximately 45 kg (100 lb). Remove motor head
assembly (16).
Illustration 11 g06253060
12. Remove bearing (17) and O-ring seal (18).
6/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 12 g06253330
13. Reinstall the washers and nuts from Tooling (C) that were removed in a previous Step.
14. Remove springs (19), O-ring seal (20), port plate (21), O-ring seal (22), plug (23), and the O
-ring seal.
Note: Port plate (21) may still be adhered to the bottom of motor head assembly (16).
Illustration 13 g06253333
15. Remove orifice (24) and orifice (25).
Illustration 14 g06253335
7/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 16. Remove plug (26).
Illustration 15 g06253475
17. Use Tooling (E) and suitable prying devices to remove piston assembly (27).
Illustration 16 g06253502
Illustration 17 g06253508
Typical example.
18. Remove separator plates (28) and friction plates (29). Note the alternating order of separator
plates (28) and friction plates (29) for assembly purposes.
8/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 18 g06253734
19. Remove barrel assembly (30).
Note: Do not allow the components of barrel assembly (30) to come apart while you
remove barrel assembly (30). The components of barrel assembly (30) must be reinstalled
into the original positions.
Illustration 19 g06253741
20. Remove piston assemblies (31) and retainer (32).
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 20 g06253748
21. Remove guide (33).
Illustration 21 g06253755
22. Remove springs (34).
Illustration 22 g06254252
23. Put location marks on swashplate (35) for assembly purposes. Remove swashplate (35).
10/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 23 g06254282
24. Remove snap ring (37) and roller (36).
Illustration 24 g06254306
25. Remove keys (38).
Illustration 25 g06254363
26. Remove snap ring (40).
27. Use a soft faced hammer to remove shaft assembly (39).
11/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 26 g06254423
28. Remove snap ring (41).
29. Use a suitable press to remove bearing (42) from shaft assembly (39).
Illustration 27 g06254449
30. Remove O-ring seal (43) and O-ring seal (44).
Illustration 28 g06254465
12/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 29 g06254467
31. Remove plug (45) and use compressed air to remove piston (46).
Illustration 30 g06254480
32. Remove lip seal (47).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 23 20:13:21 UTC+0800 2020
13/13
349F & 349F L Excavators HPD00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...