This document provides instructions for disassembling and assembling the hydraulic fan drive on a 349E excavator. The disassembly process involves removing 22 components in a specific order, taking care to contain fluids and prevent dirt entry. The assembly process reverses the disassembly steps and includes applying sealants and torquing bolts to the specified ranges. Precision and cleanliness are important to prevent damage to components.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...zatao0179249295
The document provides instructions for disassembling and assembling a hydraulic fan drive on an excavator. The disassembly process involves removing 22 components from the fan drive including bolts, seals, retainers, discs, and bearings. The assembly process reverses the disassembly steps and provides illustrations of each step. Precautions are listed regarding cleanliness, handling components, and properly assembling spring-loaded parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. The disassembly process involves removing 22 components from the fan drive including bolts, retainers, seals, discs, plates, and bearings. The assembly process is the reverse and includes applying sealant and installing the components in the proper order and orientation using various tools. Special care must be taken when handling springs and seals. Cleanliness is important to prevent contamination.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and plates. The drive flange, cover assembly, and clutch housing assembly are then separated from the case. Individual clutch components like discs and plates are removed. Reassembly involves reversing the disassembly steps and carefully reinstalling components like bearings, seals, springs, and retainers in the proper order and orientation. Precautions are outlined to prevent damage and contain fluids.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...yinranhe0814
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include:
1. Removing components like the sensor, retainer, O-rings, drive flange, and clutch housing assembly.
2. Separating the cover assembly from the case and removing internal components like seals, bearings, plates, and springs.
3. Dismantling the shaft assembly by removing seals, sleeves, and retainers.
4. Reassembling follows the reverse order, taking care to clean parts and replace worn components using the provided tools.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...wfu089267
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and bearings from the drive flange, cover assembly, case, clutch housing, and shaft assembly. The assembly procedure outlines installing these components in reverse order and notes that cleanliness is important to prevent damage to precision parts. Special care must be taken when handling spring-loaded or sealed parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and plates. The drive flange, cover assembly, and clutch housing assembly are then separated from the case. Individual parts like bearings, seals, springs, and discs are removed or installed. Precautions are outlined to prevent damage and contain fluids. The assembly procedure reverses the disassembly steps and notes to clean parts and apply sealants in the proper locations.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual Instant D...f89siekkmdmm2w
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 17 components including bolts, retainers, seals, and shafts using various tools.
3) The assembly process reverses the disassembly steps and provides notes on cleaning, inspecting, and applying sealant to parts during reassembly.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual Instant D...f8uejkdkdmm3e
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly follows the reverse order, applying sealant and pressing components back together using various tools. Proper cleaning and inspection of parts is emphasized.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...zatao0179249295
The document provides instructions for disassembling and assembling a hydraulic fan drive on an excavator. The disassembly process involves removing 22 components from the fan drive including bolts, seals, retainers, discs, and bearings. The assembly process reverses the disassembly steps and provides illustrations of each step. Precautions are listed regarding cleanliness, handling components, and properly assembling spring-loaded parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. The disassembly process involves removing 22 components from the fan drive including bolts, retainers, seals, discs, plates, and bearings. The assembly process is the reverse and includes applying sealant and installing the components in the proper order and orientation using various tools. Special care must be taken when handling springs and seals. Cleanliness is important to prevent contamination.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and plates. The drive flange, cover assembly, and clutch housing assembly are then separated from the case. Individual clutch components like discs and plates are removed. Reassembly involves reversing the disassembly steps and carefully reinstalling components like bearings, seals, springs, and retainers in the proper order and orientation. Precautions are outlined to prevent damage and contain fluids.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...yinranhe0814
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include:
1. Removing components like the sensor, retainer, O-rings, drive flange, and clutch housing assembly.
2. Separating the cover assembly from the case and removing internal components like seals, bearings, plates, and springs.
3. Dismantling the shaft assembly by removing seals, sleeves, and retainers.
4. Reassembling follows the reverse order, taking care to clean parts and replace worn components using the provided tools.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...wfu089267
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and bearings from the drive flange, cover assembly, case, clutch housing, and shaft assembly. The assembly procedure outlines installing these components in reverse order and notes that cleanliness is important to prevent damage to precision parts. Special care must be taken when handling spring-loaded or sealed parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and plates. The drive flange, cover assembly, and clutch housing assembly are then separated from the case. Individual parts like bearings, seals, springs, and discs are removed or installed. Precautions are outlined to prevent damage and contain fluids. The assembly procedure reverses the disassembly steps and notes to clean parts and apply sealants in the proper locations.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual Instant D...f89siekkmdmm2w
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 17 components including bolts, retainers, seals, and shafts using various tools.
3) The assembly process reverses the disassembly steps and provides notes on cleaning, inspecting, and applying sealant to parts during reassembly.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual Instant D...f8uejkdkdmm3e
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly follows the reverse order, applying sealant and pressing components back together using various tools. Proper cleaning and inspection of parts is emphasized.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to contain hydraulic fluids.
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, relief valves, pistons, barrel assembly, swashplate and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L XE Excavator (Prefix MTW) Service Repair Manual (MTW00...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar Cat 336F L XE Excavator (Prefix YBH) Service Repair Manual (YBH00...jdksmmdmdd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special care must be taken when removing components under spring pressure. Tools and safety precautions are listed for each step. The goal is to disassemble all parts while keeping them organized for proper reassembly.
This document provides instructions to disassemble a travel motor on a 349F and 349F L excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, port plate, springs, seals, bearings, valves and more. Precautions are provided to be aware of parts under spring force. Various specialized tools are required to properly support, attach, extract and remove components from the motor.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It details 22 steps for disassembly, removing components like bolts, retainers, seals, discs, and housing pieces. It then details 14 steps for reassembly, including pressing in bearings and seals, installing retaining rings, and pressing the shaft assembly back into place using the proper tools. Cleanliness is emphasized throughout to prevent contamination of precision components.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Personal protective equipment is recommended when removing parts with stored spring energy. Tools include lifting devices, bolts, nuts, and specialized pullers and presses. Drained fluids must be contained and disposed of properly.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...jdksmmdmdd
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation during reassembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, and more. Safety notices are included to handle parts carefully and avoid contamination when disassembling components.
Caterpillar Cat 349D2 L Excavator (Prefix GAX) Service Repair Manual (GAX0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, reinstalling these components in reverse order and noting to clean all parts and replace seals and gaskets. Precautions are provided to contain fluids, mark parts locations, and avoid contaminating the hydraulic system.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
This document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like plates and seals. It then describes removing the head, brake piston, disks, and rotating group. Components like the shaft, bearings, and pistons are then removed from the rotating group. Reassembly involves reversing these steps and ensuring components like O-rings and washers are properly installed. Precautions are provided to prevent contamination and correctly identify parts.
Caterpillar Cat 336D2 L Excavator (Prefix FAJ) Service Repair Manual (FAJ0000...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
This document provides instructions for disassembling the travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 27 steps to remove parts like the motor head assembly, springs, pistons, seals, plates and other components. Various tools are required including bolts, retaining ring pliers, drivers and pullers. Precautions are mentioned to relieve spring pressure safely and contain fluids. The process yields individual parts to allow inspection and replacement of worn items.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to contain hydraulic fluids.
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, relief valves, pistons, barrel assembly, swashplate and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L XE Excavator (Prefix MTW) Service Repair Manual (MTW00...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar Cat 336F L XE Excavator (Prefix YBH) Service Repair Manual (YBH00...jdksmmdmdd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special care must be taken when removing components under spring pressure. Tools and safety precautions are listed for each step. The goal is to disassemble all parts while keeping them organized for proper reassembly.
This document provides instructions to disassemble a travel motor on a 349F and 349F L excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, port plate, springs, seals, bearings, valves and more. Precautions are provided to be aware of parts under spring force. Various specialized tools are required to properly support, attach, extract and remove components from the motor.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It details 22 steps for disassembly, removing components like bolts, retainers, seals, discs, and housing pieces. It then details 14 steps for reassembly, including pressing in bearings and seals, installing retaining rings, and pressing the shaft assembly back into place using the proper tools. Cleanliness is emphasized throughout to prevent contamination of precision components.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Personal protective equipment is recommended when removing parts with stored spring energy. Tools include lifting devices, bolts, nuts, and specialized pullers and presses. Drained fluids must be contained and disposed of properly.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...jdksmmdmdd
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation during reassembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, and more. Safety notices are included to handle parts carefully and avoid contamination when disassembling components.
Caterpillar Cat 349D2 L Excavator (Prefix GAX) Service Repair Manual (GAX0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, reinstalling these components in reverse order and noting to clean all parts and replace seals and gaskets. Precautions are provided to contain fluids, mark parts locations, and avoid contaminating the hydraulic system.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
This document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like plates and seals. It then describes removing the head, brake piston, disks, and rotating group. Components like the shaft, bearings, and pistons are then removed from the rotating group. Reassembly involves reversing these steps and ensuring components like O-rings and washers are properly installed. Precautions are provided to prevent contamination and correctly identify parts.
Caterpillar Cat 336D2 L Excavator (Prefix FAJ) Service Repair Manual (FAJ0000...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
This document provides instructions for disassembling the travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 27 steps to remove parts like the motor head assembly, springs, pistons, seals, plates and other components. Various tools are required including bolts, retaining ring pliers, drivers and pullers. Precautions are mentioned to relieve spring pressure safely and contain fluids. The process yields individual parts to allow inspection and replacement of worn items.
Joyce M Sullivan, Founder & CEO of SocMediaFin, Inc. shares her "Five Questions - The Story of You", "Reflections - What Matters to You?" and "The Three Circle Exercise" to guide those evaluating what their next move may be in their careers.
Leadership Ambassador club Adventist modulekakomaeric00
Aims to equip people who aspire to become leaders with good qualities,and with Christian values and morals as per Biblical teachings.The you who aspire to be leaders should first read and understand what the ambassador module for leadership says about leadership and marry that to what the bible says.Christians sh
Learnings from Successful Jobs SearchersBruce Bennett
Are you interested to know what actions help in a job search? This webinar is the summary of several individuals who discussed their job search journey for others to follow. You will learn there are common actions that helped them succeed in their quest for gainful employment.
How to Prepare for Fortinet FCP_FAC_AD-6.5 Certification?NWEXAM
Begin Your Preparation Here: https://bit.ly/3VfYStG — Access comprehensive details on the FCP_FAC_AD-6.5 exam guide and excel in the Fortinet Certified Professional - Network Security certification. Gather all essential information including tutorials, practice tests, books, study materials, exam questions, and the syllabus. Solidify your knowledge of Fortinet FCP_FAC_AD-6.5 certification. Discover everything about the FCP_FAC_AD-6.5 exam, including the number of questions, passing percentage, and the time allotted to complete the test.
IT Career Hacks Navigate the Tech Jungle with a RoadmapBase Camp
Feeling overwhelmed by IT options? This presentation unlocks your personalized roadmap! Learn key skills, explore career paths & build your IT dream job strategy. Visit now & navigate the tech world with confidence! Visit https://www.basecamp.com.sg for more details.
Job Finding Apps Everything You Need to Know in 2024SnapJob
SnapJob is revolutionizing the way people connect with work opportunities and find talented professionals for their projects. Find your dream job with ease using the best job finding apps. Discover top-rated apps that connect you with employers, provide personalized job recommendations, and streamline the application process. Explore features, ratings, and reviews to find the app that suits your needs and helps you land your next opportunity.
Resumes, Cover Letters, and Applying OnlineBruce Bennett
This webinar showcases resume styles and the elements that go into building your resume. Every job application requires unique skills, and this session will show you how to improve your resume to match the jobs to which you are applying. Additionally, we will discuss cover letters and learn about ideas to include. Every job application requires unique skills so learn ways to give you the best chance of success when applying for a new position. Learn how to take advantage of all the features when uploading a job application to a company’s applicant tracking system.
Jill Pizzola's Tenure as Senior Talent Acquisition Partner at THOMSON REUTERS...dsnow9802
Jill Pizzola's tenure as Senior Talent Acquisition Partner at THOMSON REUTERS in Marlton, New Jersey, from 2018 to 2023, was marked by innovation and excellence.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i05239586
Fan Drive - Disassemble - Hydraulic Fan Drive
SMCS - 1359-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 9U-7480 Compressing Tube 1
C 1P-1859 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
Start By:
a. Remove the Hydraulic fan Drive. Refer to Disassembly and Assembly, "Fan Drive -
Remove and Install".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, thoroughly
clean the exterior of the components. This procedure will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01208862
1. Remove bolt (2) and sensor (1).
Illustration 2 g01333292
2. Remove bolts (3). Remove retainer (4).
2/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01333295
Illustration 4 g02089003
3. Remove O-ring seal (5) and drive flange (6).
4. Firmly secure drive flange (6) with a suitable vise. Protect drive flange (6) in order to
prevent damage during clamping.
5. Use a hammer and a chisel in order to break sleeve (6A). Use extreme care to prevent
damage to drive flange (6).
3/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01208866
6. Remove bolts (7). Separate cover assembly (8) from case (9).
Illustration 6 g01333297
7. Position cover assembly (8) on the opposite side.
8. Remove O-ring seal (10) from cover assembly (8).
Illustration 7 g01208919
9. Use a suitable press in order to separate cover assembly (8) and clutch housing assembly
(11).
4/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01258470
10. Remove lip seal (12). Use Tooling (A) in order to remove retaining ring (13). Use a suitable
press in order to remove bearing (14).
Illustration 9 g01208920
Note: Note the order of all the components in the clutch assembly.
11. Remove retaining ring (15). Remove retaining plate (16). Remove discs and clutch plates
(17).
Illustration 10 g01333298
5/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Use Tooling (B) and a suitable press to reposition piston (18). Use Tooling (C) in order to
remove retaining ring (19). Remove piston (18).
Illustration 11 g01333300
13. Remove seal (20) from piston (18).
Illustration 12 g01333301
14. Remove spring (21) from clutch housing assembly (11).
6/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g01333303
15. Remove seal rings (22) from shaft assembly (24). Use Tooling (D) in order to remove
retaining ring (23).
Illustration 14 g02089058
16. Use a suitable press in order to remove shaft assembly (24) from case (9).
Illustration 15 g02089073
17. Remove seal (25) from shaft assembly (24).
7/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 18. Firmly secure shaft assembly (24) with a suitable vise. Protect shaft assembly (24) in order
to prevent damage during clamping.
19. Use a hammer and a chisel in order to break sleeve (30). Use extreme care to prevent
damage to shaft assembly (24).
Illustration 16 g01333308
20. Remove tube assembly (26) from case (9).
Illustration 17 g01333310
21. Remove lip seal (27) from case (9).
8/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01333314
22. Use Tooling (A) in order to remove retaining ring (28). Use a suitable press in order to
remove bearing (29) from case (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 23:54:22 UTC+0800 2020
9/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142230
Fan Drive - Disassemble - Direct Drive
SMCS - 1359-015
Disassembly Procedure
Start By:
A. Remove the fan drive (direct drive).
Illustration 1 g02341528
1. Remove bolt (8), plate (7), bearing assembly (5), hub assembly (4), spacer (3), and bearing
assembly (2) from bracket assembly (1) .
2. Remove spring pin (6) from plate (7) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 23:55:17 UTC+0800 2020
1/2
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i06192451
Fan Drive - Assemble - Hydraulic Fan Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 9U-7480 Compressing Tube 1
C 1P-1859 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
E - Loctite Flexible Anaerobic Gasket Flange 1
F - Loctite 648 1
G 359-4915 Driver 1
H 359-4916 Driver 1
Note: Caution is required while handling the lip seals. The lip seals can be damaged if objects or
cleaning fluids contact the sealing surface.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts except the lip
seals with cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to
dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
1/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01333314
1. Use a suitable press to install bearing (29) into case (9) . Use Tooling (A) in order to install
retaining ring (28) .
Illustration 2 g01333310
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
2. Apply Tooling (E) to the outside diameter of lip seal (27) . Carefully install lip seal (27) into
case (9) .
2/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g02092525
3. Install seal (25) onto shaft assembly (24) .
4. Apply Tooling (F) to the full diameter of the shoulder on shaft assembly (24) . Position new
sleeve (30) on shaft assembly (24) . The external chamfer on sleeve (30) will be on top. Use
Tooling (G) and a suitable press in order to install sleeve (30) . Remove excess Tooling (F) .
Illustration 4 g01333308
Illustration 5 g01286111
3/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 5. Position tube assembly (26) into case (9) .
6. Position case (9) and tube assembly (26) onto shaft assembly (24) .
7. Use a suitable press and a suitable driver to press shaft assembly (24) through the bearing
and through tube assembly (26) .
Illustration 6 g01333303
8. Use Tooling (D) in order to install retaining ring (23) . Install seal rings (22) onto shaft
assembly (24) .
Illustration 7 g01333301
9. Install spring (21) on clutch housing assembly (11) .
4/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 8 g01333300
10. Install seal (20) on piston (18) .
Illustration 9 g01333298
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11. Install piston (18) . Use Tooling (B) and a suitable press in order to position piston (18) .
Use Tooling (C) in order to install retaining ring (19) . Carefully release the tension on
Tooling (B) .
5/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 10 g01208920
12. Install clutch plates (16) and discs (17) . Install retaining ring (15) .
Illustration 11 g01209073
13. Position cover assembly (8) onto clutch housing assembly (11) .
Note: Make sure that the splines of cover assembly (8) fully engage all of the clutch plates
and discs in the clutch assembly.
6/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 12 g01209125
Illustration 13 g01258534
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
14. Use a suitable press in order to install bearing (14) . Use Tooling (A) in order to install
retaining ring (13) . Install lip seal (12) .
Illustration 14 g01333297
15. Position cover assembly (8) on the opposite side.
16. Install O-ring seal (10) on cover assembly (8) .
7/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 15 g01208914
17. Position cover assembly (8) onto case (9) . Install bolts (7) and tighten bolts (7) to a
minimum torque of 18 N·m (13 lb ft) up to a maximum torque of 31 N·m (23 lb ft).
Illustration 16 g02092935
18. Apply Tooling (F) to the full diameter of the shoulder on drive flange (6) . Position new
sleeve (6A) on drive flange (6) . The external chamfer on sleeve (6A) will be on top. Use
Tooling (H) and a suitable press in order to install sleeve (6A) . Remove excess Tooling
(F) .
8/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 17 g01333295
19. Install drive flange (6) and O-ring seal (5) .
Illustration 18 g01333292
20. Install retainer (4) . Tighten retainer (4) to a minimum torque of 610 N·m (450 lb ft) up to a
maximum torque of 750 N·m (550 lb ft). After achieving the torque range, overtighten
retainer (4) as needed in order to align the next position for locking screws (3) .
21. Install locking screws (3) and tighten locking screws (3) to a minimum torque of 7 N·m (62
lb in) to a maximum torque of 10 N·m (89 lb in).
9/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 19 g01208862
22. Position sensor (1) . Install bolt (2) .
End By: Install the fan clutch. Refer to Disassembly and Assembly, "Fan Clutch - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 23:56:13 UTC+0800 2020
10/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engin...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142231
Fan Drive - Assemble - Direct Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Illustration 1 g02341528
1. Install spring pin (6) into plate (7) .
2. Apply Tooling (A) to the threads of bolt (8). Install bearing assembly (2), spacer (3), hub
assembly (4), bearing assembly (5), plate (7), and bolt (8) onto bracket assembly (1).
Tighten bolt (8) to a torque of 115 ± 15 N·m (85 ± 11 lb ft).
1/2
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. End By: Install the fan drive (direct drive).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 23:57:09 UTC+0800 2020
2/2
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04108512
Water Pump - Remove and Install
SMCS - 1361-010; 1361-011; 1361-012
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Start By:
A. Remove the water temperature regulator.
B. Remove fan drive.
Illustration 1 g02310883
1/4
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 1. Remove bolts (1) and sheet assembly (2). Remove bolts (3) and sheet assembly (4) .
Illustration 2 g02311921
2. Remove step (6), sheet assembly (5), sheet assembly (7), and sheet assembly (8) .
Illustration 3 g02311923
Note: Open the hoods to the FULLY OPEN position.
3. Disconnect support assembly (9). Use suitable cribbing to support the support assembly (9) .
4. Remove support assembly (10) and support assembly (11) .
2/4
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...