This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. The removal procedure involves using various tools to remove 11 components in 11 steps, including gears, covers, seals, and bearings. The installation procedure involves 14 steps of lowering temperatures of bearings, applying seals and lubricants, and ensuring proper dimensions when reinstalling components. Special care and tools are required to handle heavy components like the flywheel.
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...zatao0179249295
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing and installing the rear gear group components like gears, covers, seals, and bearings. Precise measurements and tooling are required for proper installation.
- Procedures for removing and installing the flywheel, which requires lifting equipment due to its weight. The ring gear must be heated for removal and cooled for installation.
- Removing and installing the crankshaft rear seal using specific bolts and torque specifications. Inspection of the crankshaft surface is also noted.
Precise measurements and use of the correct tools are emphasized for correct re
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...yinranhe0814
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a 349D L Excavator powered by a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers and bearings. The installation procedure provides steps to install these components in reverse order and includes notes about tool usage and matching dimensions.
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...wfu089267
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing and installing the rear gear group components like gears, covers, seals, and bearings. Precise measurements and tooling are required for proper installation.
- Procedures for removing and installing the flywheel, which requires lifting equipment due to its weight. The ring gear must be heated for removal and cooled for installation.
- Removing and installing the crankshaft rear seal using specific bolts and torque specifications. Inspection of the crankshaft surface is also noted.
Precise measurements and use of the correct tools are emphasized for correct re
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...zatao0179249295
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing and installing the rear gear group components like gears, covers, seals, and bearings. Precise measurements and tooling are required for proper installation.
- Procedures for removing and installing the flywheel, which requires lifting equipment due to its weight. The ring gear must be heated for removal and cooled for installation.
- Removing and installing the crankshaft rear seal using specific bolts and torque specifications. Inspection of the crankshaft surface is also noted.
Precise measurements and use of the correct tools are emphasized for correct re
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...yinranhe0814
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a 349D L Excavator powered by a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers and bearings. The installation procedure provides steps to install these components in reverse order and includes notes about tool usage and matching dimensions.
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...wfu089267
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing and installing the rear gear group components like gears, covers, seals, and bearings. Precise measurements and tooling are required for proper installation.
- Procedures for removing and installing the flywheel, which requires lifting equipment due to its weight. The ring gear must be heated for removal and cooled for installation.
- Removing and installing the crankshaft rear seal using specific bolts and torque specifications. Inspection of the crankshaft surface is also noted.
Precise measurements and use of the correct tools are emphasized for correct re
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...ifkkdkmdmd
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying loctite to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...yqen95561858
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and multi-step procedures involving removing and installing various components like bolts, seals, gears, and bearings.
3. Precise instructions are given regarding tool usage, component orientation, and torque specifications to correctly disassemble and reassemble the rear of the engine.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...ufs89eodkdmdm
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkskmmdmd1
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling, inspecting, and reassembling each component.
3. Special attention is given to bearing installation and torque specifications for fasteners.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkksmemmd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required include drivers, link brackets, guide studs, and installation tools.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...jjfksekdmejik
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...yqen95561858
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the assembly process. Torque specifications are provided for securing different fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, pressing bearings in at the proper angles and depths, and torquing bolts to the specified values.
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and compression brake valve assembly. The procedures include illustrations of the components and multi-step instructions for removal and installation, including proper torque specifications. Safety precautions are provided where necessary.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C15 or C18 engine. It describes removing components like the crankshaft rear seal, electric starting motor, and rear power take-off. It then explains how to use lifting tools to remove the flywheel housing and reinstall it, replacing seals and tightening bolts in a specific sequence and torque range. Similar instructions are provided for removing and installing just the rear power take-off components.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
More Related Content
Similar to Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual Instant Download.pdf
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...ifkkdkmdmd
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying loctite to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...yqen95561858
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and multi-step procedures involving removing and installing various components like bolts, seals, gears, and bearings.
3. Precise instructions are given regarding tool usage, component orientation, and torque specifications to correctly disassemble and reassemble the rear of the engine.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...ufs89eodkdmdm
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkskmmdmd1
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling, inspecting, and reassembling each component.
3. Special attention is given to bearing installation and torque specifications for fasteners.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkksmemmd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required include drivers, link brackets, guide studs, and installation tools.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...jjfksekdmejik
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...yqen95561858
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Similar to Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual Instant Download.pdf (14)
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the assembly process. Torque specifications are provided for securing different fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, pressing bearings in at the proper angles and depths, and torquing bolts to the specified values.
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and compression brake valve assembly. The procedures include illustrations of the components and multi-step instructions for removal and installation, including proper torque specifications. Safety precautions are provided where necessary.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C15 or C18 engine. It describes removing components like the crankshaft rear seal, electric starting motor, and rear power take-off. It then explains how to use lifting tools to remove the flywheel housing and reinstall it, replacing seals and tightening bolts in a specific sequence and torque range. Similar instructions are provided for removing and installing just the rear power take-off components.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals.
4. Disassembling the scavenge pump by removing O-rings, bearings, shafts, and gears.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before disassembling the recoil spring components.
3. Reassembling the recoil spring components and using the tooling bench to apply controlled compression for assembly. Proper centering and leveling of the assembly is critical.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 657E wheel tractor. The removal procedure involves using various tools to disassemble the rear gear components and adapter assemblies. The installation procedure describes reassembling these components and requires pressing or installing bearings and seals using a driver group or press. Special care must be taken to keep parts clean and lubricated. The flywheel removal uses tools to secure the crankshaft gear and hoist the heavy flywheel off the engine.
This document provides instructions for installing and removing various engine components on a Caterpillar 657E wheel scraper model powered by a 3408 engine, including:
1) Installing the rear gear group by placing gears and bearings on shafts and installing dowels, seals and bolts.
2) Removing the flywheel using guide bolts, brackets and a hoist to lift the heavy flywheel off the crankshaft.
3) Installing the flywheel by heating the ring gear, placing the flywheel on guide bolts, and bolting it into place.
4) Procedures for removing and installing the crankshaft rear seal using punch tools or pullers
The document provides instructions for installing the crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes heating the ring gear to 300°C before installing it on the flywheel. It also details installing guide bolts and lifting brackets to position the flywheel, applying grease to the bolt threads, and torquing the bolts to secure the flywheel. Finally, it notes to check the flywheel runout after installation.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The steps include removing the transmission transfer gears as a unit, disassembling the individual gears and bearings, inspecting and replacing parts, and reassembling the gears and bearings in the correct order with the specified torques and clearances. Precautions are provided such as cleaning and lubricating parts during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling various components of a 651B wheel scraper model, including:
1. The engine transfer gear and retarder, with steps to remove gears, bearings, and housing pieces.
2. The transmission transfer gear, with steps to remove gears, bearings, pumps, and the governor.
3. The transmission governor, with identification of parts and steps to disassemble and reassemble the governor valve bodies.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR FLA
Configuration: 349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06931709
Gear Group (Rear) - Remove and Install
SMCS - 1206-010; 1212-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp. 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the electric starting motor.
b. Remove the flywheel.
1. Support the engine.
1/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g06002548
2. Remove bolts (2) and rear crankshaft seal (1).
Illustration 2 g06002556
3. Remove bolts (4) and the washers. Remove cover (3) and the seal.
Illustration 3 g06002558
4. Remove gear (7), bolts (6), and gear (5).
Illustration 4 g06002564
2/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Remove O-ring seal (8) from gear (7).
Illustration 5 g06172622
6. Use Tooling (A) to remove bushing (7A) from gear assembly (7).
Illustration 6 g06172537
7. Remove bolts (9), adapter assembly (10), and the O-ring seal.
Illustration 7 g06172541
8. Use Tooling (B) to remove bearing (11) from adapter assembly (10).
3/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g06172549
9. Remove gear assembly (12).
Illustration 9 g06172554
10. Remove cover (13) and the O-ring seal.
Illustration 10 g06172557
11. Use Tooling (B) to remove bearing (14).
Installation Procedure
4/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Table 2
Required Tools
Tool Part Number Part Description Qty
A 095-0706 Bolt 2
Illustration 11 g06172557
Illustration 12 g06172580
5/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 13 g06172587
1. Lower the temperature of bearing (14). Be sure to match Dimension (B) and Dimension (C)
when installing bearing (14.). Dimension (B) indicates the angle of the joint on bearing (14).
Dimension (B) is 15° ± 1°. Dimension (C) shows the distance from bearing (14) to the end
of the bore. Dimension (C) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
Illustration 14 g06172554
2. Install the O-ring seal and cover (9).
6/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g06172597
3. Install gear assembly (12) with oil passage plug (12A) facing out.
Illustration 16 g06172601
Illustration 17 g06172609
4. Lower the temperature of bearing (11). Be sure to match Dimension (F) and Dimension (G)
when installing bearing (11) into adapter assembly (10). Dimension (F) indicates the angle
of the joint on bearing (11). Dimension (F) is 15° ± 1°. Dimension (G) shows the distance
from bearing (11) to the end of the bore. Dimension (G) is 3.500 ± 0.500 mm
(0.1378 ± 0.0197 inch).
7/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g06172537
5. Install the O-ring seal, adapter assembly (10), and bolts (9).
Illustration 19 g06172619
6. Lower the temperature of bearing (7A). Install bearing (7A) into gear assembly (7). Be sure
that each relief (H) is within 2° of each relief in gear assembly (7).
Illustration 20 g06002564
7. Install O-ring seal (8) onto gear (7).
8/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 21 g06002578
8. Install gear (5) and bolts (6).
Note: Tooling (A) is for supporting gear (7) during the installation of the cover and the rear
crankshaft seal.
Note: The bolt holes in gear (7) are not symmetrical. When installing Tooling (C), check
the rest of the bolts holes in gear (7) are aligned with the holes in the crankshaft.
9. Install gear (7) and Tooling (C).
Illustration 22 g06002581
10. Install cover (3), the seal, bolts (4), and the washers.
9/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g06002592
11. Install rear crankshaft seal (1) and bolts (2).
12. Remove Tooling (C).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 20:04:02 UTC+0800 2020
10/10
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR FLA
Configuration: 349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249234
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
1/2
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01132214
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 79 kg (175 lb).
2. Remove top bolt (1). Install Tooling (B).
3. Remove remaining bolts (1).
4. Remove flywheel (2).
5. Use a hammer and a punch in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 20:04:58 UTC+0800 2020
2/2
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR FLA
Configuration: 349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06123534
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
C - Loctite 242 1
Always wear protective gloves when handling parts that have been
heated.
1. Raise the temperature of the ring gear. Position the ring gear with the part number toward
the crankshaft. Install the ring gear on the flywheel. Allow the ring gear to cool. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel.
1/2
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01132214
2. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 79 kg (175 lb).
3. Position flywheel (2) on Tooling (B) .
4. Apply Tooling (C) to bolts (1) .
5. Install bolts (1) . Remove Tooling (B) . Install remaining bolt (1) . Tighten the bolts evenly
to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 20:05:54 UTC+0800 2020
2/2
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR FLA
Configuration: 349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010889
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01132235
1. Remove bolts (1).
2. Remove crankshaft rear seal (2).
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 20:06:49 UTC+0800 2020
2/2
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR FLA
Configuration: 349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010890
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place to dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 20:07:45 UTC+0800 2020
3/3
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D L EXCAVATOR FLA
Configuration: 349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249340
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
1. Support the engine.
Illustration 1 g01132273
1/3
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
23. 2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb).
3. Remove bolts (1) and flywheel housing (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Sealant 1
1. Apply Tooling (A) to the face of the cylinder block.
Illustration 2 g01132273
2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb). Position flywheel housing (2) on the rear of the cylinder
block.
3. Install bolts (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Aug 17 20:08:41 UTC+0800 2020
2/3
349D L Excavator FLA00001-UP (MACHINE) POWERED BY C13 Engine(SEBP65...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...