The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
Caterpillar cat 345 c l hydraulic excavator (prefix esd) service repair manua...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor. It begins with required tools and safety notices. The disassembly procedure has 31 steps that remove components like the head, plates, seals, pistons and housing pieces. The assembly procedure has 14 steps that install components in reverse order, noting to clean parts and apply lubricant before assembling. It emphasizes replacing all seals and O-rings with new parts.
Caterpillar cat 345 c hydraulic excavator (prefix esd) service repair manual ...fjsekqazxkdmmem
The document provides instructions for disassembling and assembling a travel motor. It begins with required tools and safety notices. The disassembly procedure has 31 steps that remove components like the head, plates, seals, pistons and housing pieces. The assembly procedure has 14 steps that install components in reverse order, noting to clean parts and apply lubricant before assembling. It emphasizes replacing all seals and O-rings with new parts.
Caterpillar cat 345 c hydraulic excavator (prefix esd) service repair manual ...fjskekmdm
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper cleaning and installation of parts is emphasized to prevent contamination of the hydraulic system and ensure correct assembly.
Caterpillar cat 345 c l hydraulic excavator (prefix esd) service repair manua...fjjskqazxedmmem
The document provides instructions for disassembling and assembling a travel motor. It begins with required tools and safety notices. The disassembly procedure has 31 steps that remove components like the head, plates, disks, seals and pins. The assembly procedure has 16 steps that install components like seals, spacers, washers, rings and plates in reverse order of disassembly. Tolerances and torque specifications are provided for correct assembly.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...kmf9ioseodk
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and housing pieces. It notes to mark parts locations and orientations. Reassembly follows the reverse order, and notes to clean parts and avoid damaging mating surfaces.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix TDG) Service Repa...yan77xunhao
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and housing pieces. The instructions emphasize cleaning parts and marking components to ensure proper reassembly. Reassembly follows the disassembly steps in reverse order.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix TDG) Service Repair Manual...f8usiejdkmdd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, replacing components in reverse order and noting to clean all parts, apply lubricant, and measure clearances during assembly to ensure correct orientation. Tools required are listed for both disassembly and assembly.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, apply lubricant, and replace all seals and gaskets. Precise measurements and tooling are required to properly assemble the travel motor.
Caterpillar cat 345 c l hydraulic excavator (prefix esd) service repair manua...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor. It begins with required tools and safety notices. The disassembly procedure has 31 steps that remove components like the head, plates, seals, pistons and housing pieces. The assembly procedure has 14 steps that install components in reverse order, noting to clean parts and apply lubricant before assembling. It emphasizes replacing all seals and O-rings with new parts.
Caterpillar cat 345 c hydraulic excavator (prefix esd) service repair manual ...fjsekqazxkdmmem
The document provides instructions for disassembling and assembling a travel motor. It begins with required tools and safety notices. The disassembly procedure has 31 steps that remove components like the head, plates, seals, pistons and housing pieces. The assembly procedure has 14 steps that install components in reverse order, noting to clean parts and apply lubricant before assembling. It emphasizes replacing all seals and O-rings with new parts.
Caterpillar cat 345 c hydraulic excavator (prefix esd) service repair manual ...fjskekmdm
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper cleaning and installation of parts is emphasized to prevent contamination of the hydraulic system and ensure correct assembly.
Caterpillar cat 345 c l hydraulic excavator (prefix esd) service repair manua...fjjskqazxedmmem
The document provides instructions for disassembling and assembling a travel motor. It begins with required tools and safety notices. The disassembly procedure has 31 steps that remove components like the head, plates, disks, seals and pins. The assembly procedure has 16 steps that install components like seals, spacers, washers, rings and plates in reverse order of disassembly. Tolerances and torque specifications are provided for correct assembly.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...kmf9ioseodk
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and housing pieces. It notes to mark parts locations and orientations. Reassembly follows the reverse order, and notes to clean parts and avoid damaging mating surfaces.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix TDG) Service Repa...yan77xunhao
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and housing pieces. The instructions emphasize cleaning parts and marking components to ensure proper reassembly. Reassembly follows the disassembly steps in reverse order.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix TDG) Service Repair Manual...f8usiejdkmdd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, replacing components in reverse order and noting to clean all parts, apply lubricant, and measure clearances during assembly to ensure correct orientation. Tools required are listed for both disassembly and assembly.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, reinstalling these components in reverse order and noting to clean all parts, apply lubricant, and replace all seals and gaskets. Precise measurements and tooling are required to properly assemble the travel motor.
Caterpillar Cat 325C FM EXCAVATOR (Prefix Y4P) Service Repair Manual (Y4P0000...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C FM excavator. It lists the required tools and parts. The disassembly procedure involves removing over 30 components of the final drive including sprockets, gears, seals, plates, and housings. Detailed illustrations are provided to show how to remove each part correctly. The assembly procedure is not included.
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...ufs89eodkdmdm
The document provides instructions for assembling a travel motor on an excavator. It details 27 steps including installing seals, springs, pistons and other components into the motor housing. The motor is then installed onto the final drive assembly and excavator frame using bolts. Proper lubrication and torque specifications are emphasized to correctly assemble the travel motor.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It describes 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Precautions are provided to ensure fluids are contained and parts are cleaned before assembly. Tools required are listed. Lubrication and heating of some parts is specified before installation.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold and slip joints.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the cylinder head
The procedures describe draining fluids, removing bolts and hoses, cleaning parts, replacing seals, and torquing fasteners to the specified values. Special tools are listed for many of the removal and installation steps.
This document provides instructions for removing and installing inlet and exhaust valves on a C27 Industrial Engine. It describes:
- Using a valve spring compressor tool to remove the valve springs and valve spring retainers.
- Inspecting the valves and checking the spring force.
- Lubricating the valve stems before installation and compressing the springs with a tool to install the retainers.
- Cautions for wearing protective equipment when working with springs to avoid injury from parts propelled by the springs.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap-to-connect fittings, removing and installing a muffler, and removing and installing a fuel priming pump and fuel filter base.
2) The procedures include illustrations showing the components and numbered steps for disassembly and reassembly. Safety warnings are provided at the beginning regarding relieving pressures before disconnection.
3) Torque specifications and required tools are listed for relevant installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 345D L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pins, bearing, and piston assemblies. Special care must be taken to clean parts and ensure they are reinstalled in their original locations. Proper assembly prevents damage and contamination of parts.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 345D L Excavator (Prefix RGD) Service Repair Manual (RGD00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, plates, seals, pins, and piston assemblies. The instructions describe cleaning parts and ensuring they are reinstalled in their original locations to properly reassemble the travel motor.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...ufs89eodkdmdm
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Caterpillar Cat 325C FM EXCAVATOR (Prefix Y4P) Service Repair Manual (Y4P0000...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C FM excavator. It lists the required tools and parts. The disassembly procedure involves removing over 30 components of the final drive including sprockets, gears, seals, plates, and housings. Detailed illustrations are provided to show how to remove each part correctly. The assembly procedure is not included.
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...ufs89eodkdmdm
The document provides instructions for assembling a travel motor on an excavator. It details 27 steps including installing seals, springs, pistons and other components into the motor housing. The motor is then installed onto the final drive assembly and excavator frame using bolts. Proper lubrication and torque specifications are emphasized to correctly assemble the travel motor.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It describes 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Precautions are provided to ensure fluids are contained and parts are cleaned before assembly. Tools required are listed. Lubrication and heating of some parts is specified before installation.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold and slip joints.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the cylinder head
The procedures describe draining fluids, removing bolts and hoses, cleaning parts, replacing seals, and torquing fasteners to the specified values. Special tools are listed for many of the removal and installation steps.
This document provides instructions for removing and installing inlet and exhaust valves on a C27 Industrial Engine. It describes:
- Using a valve spring compressor tool to remove the valve springs and valve spring retainers.
- Inspecting the valves and checking the spring force.
- Lubricating the valve stems before installation and compressing the springs with a tool to install the retainers.
- Cautions for wearing protective equipment when working with springs to avoid injury from parts propelled by the springs.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap-to-connect fittings, removing and installing a muffler, and removing and installing a fuel priming pump and fuel filter base.
2) The procedures include illustrations showing the components and numbered steps for disassembly and reassembly. Safety warnings are provided at the beginning regarding relieving pressures before disconnection.
3) Torque specifications and required tools are listed for relevant installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 345D L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pins, bearing, and piston assemblies. Special care must be taken to clean parts and ensure they are reinstalled in their original locations. Proper assembly prevents damage and contamination of parts.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 345D L Excavator (Prefix RGD) Service Repair Manual (RGD00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, plates, seals, pins, and piston assemblies. The instructions describe cleaning parts and ensuring they are reinstalled in their original locations to properly reassemble the travel motor.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...ufs89eodkdmdm
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR ESD
Configuration: 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i02407350
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 3E-3879 Eyebolt 1
B 1P-0074 Slide Hammer Puller 1
C 6V-3010 Puller Group 1
D 4C-8359 Eyebolt 1
E 9S-9152 Bearing Puller 1
F 1P-1862 Pliers 1
G 1P-0510 Driver Group 1
H 1U-7600 Slide Hammer Puller 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Failure to properly assemble parts or failure to follow established
procedures can lead to damage to the parts and assembly.
To avoid damage to parts, always identify and mark the parts so that
they can be installed into the same location. Never force parts during
assembly. Keep parts clean and lubricated.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
2/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel
motor to a suitable holding fixture in a vertical position. The weight of the travel motor is
141 kg (310 lb).
Illustration 1 g00627438
2. Remove displacement change valve (1) from the head of the travel motor.
Illustration 2 g00624938
3. Remove O-ring seals (2) and rings (3) from the displacement change valve.
Illustration 3 g00628657
3/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plugs (5) from the head. Remove an O-ring seal from each plug.
5. Remove outer bolts (4) from the head of the travel motor.
Illustration 4 g00624949
6. Use Tooling (A) and a suitable lifting device to remove the head of the travel motor from
the travel motor housing. The weight of head (6) is approximately 43 kg (95 lb).
Note: There are pins (7) that may fall out of the inside of the head when the head is
removed.
Note: Be careful during the removal of head (6) from the travel motor housing. Be careful
not to scratch mating surfaces or damage the mating surfaces of the components.
4/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 5 g00624953
7. Turn over the head. If pins (7) are in the bottom side of the head, remove the pins.
Illustration 6 g00627405
8. Remove port plate (8) and O-ring seal (9) from the head.
Illustration 7 g00625967
9. Use Tooling (B) in order to remove bearing (10) from the head of the travel motor.
5/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 8 g00627391
10. Remove plate (11) and remove springs (12) from the travel motor housing.
11. Remove O-ring seals (13) from the upper surface of the travel motor housing.
Illustration 9 g00627377
12. Install Tooling (C) on the brake piston (14). Remove the brake piston.
Illustration 10 g00625888
13. Remove O-ring seals (15) and the backup rings from the brake piston.
Note: Make sure that you take note of the location of the O-rings versus the backup rings.
6/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g00625891
14. Remove separator plates (16) from the travel motor housing.
Illustration 12 g00666743
15. Remove disks (17) from the travel motor housing.
Illustration 13 g00626837
16. Install Tooling (D) to the shaft and use a suitable lifting device in order to remove the
rotating group from the travel motor housing. The weight of the rotating group is 29 kg
(65 lb).
7/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: Do not allow the components of the rotating group to come apart during the removal
from the travel motor. All of the components in the rotating group must be reinstalled in the
component's original location.
Illustration 14 g00626633
17. Turn over the rotating group. Remove shaft assembly (18) from the rotating group.
Illustration 15 g00666621
Illustration 16 g00625900
18. Use a suitable press to remove bearing (19) from shaft assembly (18).
8/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00666622
19. Use Tooling (E) and a suitable press in order to remove inner race (20) from shaft assembly
(18).
Illustration 18 g00625908
20. Remove cam plate (21) from the rotating group.
Illustration 19 g00625911
21. Retainer (22) and piston assemblies (23) are nonserviceable separately. Prior to the removal
of the retainer and the piston assemblies from barrel (24), put identification marks on the
piston assemblies, the retainer and the barrel for assembly purposes.
9/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 22. The piston assemblies must be reinstalled in the original bores in the retainer and the barrel.
23. Remove retainer (22) and piston assemblies (23) from barrel (24).
24. Separate the piston assemblies from the retainer.
Illustration 20 g00625917
Note: The orientation of the washers (25) is important. The washers must be reinstalled on
barrel (24) in the same orientation.
25. Remove guide (26) and outer spacer (27) from barrel (24).
26. Remove washers (25) and inner spacer (28) from the barrel.
Illustration 21 g00625937
27. Remove keys (29) from the travel motor housing.
10/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g00625920
28. Use Tooling (F) to remove retaining ring (30) from the shaft end of the travel motor
housing.
Illustration 23 g00625936
Illustration 24 g00636454
29. Use Tooling (G) to remove lip seal (31) from the travel motor housing if the shaft has been
removed from the travel motor.
11/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 30. Use Tooling (H) to remove lip seal (31) if the shaft has not been removed from the travel
motor. Place the travel motor in a vertical position when you use Tooling (H) to remove the
lip type seal.
Illustration 25 g00625976
31. Remove plug (33) and piston (32) from the travel motor housing. Remove O-ring seal (34)
from the plug.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 15 14:57:03 UTC+0800 2020
12/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR ESD
Configuration: 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i03778971
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 3E-3879 Eyebolt 1
D 4C-8359 Eyebolt 1
F 1P-1862 Pliers 1
G 1P-0510 Driver Group 1
J 4C-4030 Thread Lock Compound 1
K 180-6533 Seal Driver 1
L 6V-7030 Micrometer Depth Gauge 1
M 8T-0447 Calipers 1
N 1U-6396 O-Ring Assembly Compound 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
1/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-ring seals , gaskets, and seals should always be replaced. A used O-ring seal may not
have the same sealing properties as a new O-ring seal. Use Tooling (H) during the assembly
procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
Illustration 1 g01204890
1. Install O-ring seal (34) on plug (33).
2. Install piston (32) and the plug in the travel motor body. Tighten the plug to a torque of
430 ± 40 N·m (317 ± 30 lb ft).
2/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01204916
Illustration 3 g01204919
3. Apply a thin coat of Tooling (J) on the outer surfaces of lip seal (31).
4. Use Tooling (K) and a suitable hammer to drive the lip seal into the travel motor body.
Drive the seal downward until Tooling (K) makes contact with the travel motor housing.
5. Use Tooling (F) to install retaining ring (30) to the shaft end of the travel motor body.
Illustration 4 g01204923
6. Install keys (29) inside the travel motor body.
3/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g01204924
7. Assemble washers (25), inner spacer (28) and outer spacer (27) in the proper orientation, as
shown.
Illustration 6 g01204931
8. Use Tooling (L) to measure the distance from the outer spacer to the surface of the table.
The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check
orientation of the washers. If orientation is correct, replace washers and spacers with new
parts.
4/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g00625917
9. Install inner spacer (28), washers (25), and outer spacer (27) to barrel (24).
10. Install guide (26) to the barrel.
Illustration 8 g00625911
11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in
barrel (24).
Illustration 9 g00625908
12. Install cam plate (21) on the rotating group.
5/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 10 g00666621
Illustration 11 g00628062
13. Use a suitable press to install bearing (19) onto shaft assembly (18).
Illustration 12 g00668076
14. Use a suitable press in order to install inner race (20) onto shaft assembly (18).
Note: Place the two support plates under the lip of shaft assembly (18).
6/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g00626633
15. Insert shaft assembly (18) in the rotating group.
Illustration 14 g00625891
Illustration 15 g00666743
16. Alternate disks (17) and separator plates (16) into the travel motor housing. Start with a
separator plate and end with a separator plate.
7/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 16 g00626837
17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel
assembly into the travel motor body.
Note: Align the notches of the cam plate with the keys in the travel motor body before you
lower the barrel assembly into the travel motor body.
Illustration 17 g01204938
18. Use Tooling (M) to measure the depth from the top surface of the travel motor body to the
bronze face of the barrel assembly. The distance should be 32.2 ± 2 mm (1.27 ± 0.08 inch).
If this measurement is off, check orientation of the barrel assembly. Also check if the cam
plate is properly seated on the keys.
8/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g00625888
Illustration 19 g00667938
(15) O-Ring seals
19. Install O-ring seals (15) and the backup rings on the brake piston.
Note: Make sure that you install the backup ring and the O-ring seal in the original position.
Refer to Illustration 19.
9/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 20 g00629015
20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use
a soft faced hammer to seat the brake piston correctly.
Illustration 21 g01204953
21. Use Tooling (M) to measure the distance from the top of the brake piston (14) to the top
surface of the travel motor body. The distance should be 20.8 ± 1.0 mm (0.82 ± 0.04 inch).
If this measurement is off, drive the brake piston further into the travel motor body.
Illustration 22 g00627391
22. Install springs (12) and plate (11).
10/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 23. Install O-ring seals (13).
Illustration 23 g01204965
24. Use Tooling (G) to drive the bearing into the head.
Illustration 24 g00627405
25. Install O-ring seal (9) onto the head.
26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to
the port plate in order to hold the port plate in place during the installation of the head.
Illustration 25 g01205007
11/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 27. Turn over head (6). Install Tooling (A) onto the head. Use a suitable lifting device to install
the head onto the travel motor.
Illustration 26 g00631594
28. Install Pins (7) into the head.
Illustration 27 g00628657
29. Install an O-ring on each plug (5).
30. Install bolts (4) which hold the head in place. Tighten the six bolts to a torque of
530 ± 70 N·m (391 ± 52 lb ft).
31. Install plugs (5) that hold the pins in the head. Tighten the plugs to a torque of 75 ± 7 N·m
(55 ± 5 lb ft).
12/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 28 g00624938
32. Install O-ring seals (2) and rings (3) on the displacement change valve.
Illustration 29 g00627438
33. Install displacement change valve (1) onto the head of the travel motor. Tighten the
displacement change valve to a torque of 50 ± 3 N·m (37 ± 2 lb ft).
34. To prevent possible damage to the travel motor, the unit should be filled with oil at least up
to the fill port prior to operation. Refer to Operation and Maintenance Manual for the
correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 15 14:58:00 UTC+0800 2020
13/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...