The document provides instructions for removing, disassembling, assembling, and installing a piston motor (hydraulic fan) for Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor. Disassembly requires using various tools to remove individual components like bearings, seals, springs and pistons. Reassembly follows the reverse order, noting requirements like heating/cooling parts and using tools to install retaining rings and seals. Installation connects all hoses and mounts the assembled fan motor assembly back in place.
Caterpillar cat 336 d excavator (prefix jbt) service repair manual (jbt00001 ...fjskemdme
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to remove the fan motor by bending tabs, removing bolts and hub, and lifting the fan motor assembly. It then details disassembling the fan motor by removing the head, port plate, poppet springs, pistons, bearings and other components. Reassembly instructions are also provided, describing how to install components in reverse order and noting any special tools or precautions needed.
Caterpillar cat 336 d excavator (prefix jbt) service repair manual (jbt00001 ...fjskkkdmem
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to remove the fan motor by bending tabs, removing bolts and hub, and lifting the fan motor assembly. It then details disassembling the fan motor by removing the head, port plate, poppet springs, pistons, bearings and other components. Reassembly instructions are also provided, describing how to install components in reverse order and noting any special tools or precautions needed.
Caterpillar cat 336 d l excavator (prefix jbt) service repair manual (jbt0000...fjskemdme
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to remove the fan motor by bending tabs, removing bolts and hub, and lifting the fan motor assembly. It then details disassembling the fan motor by removing the head, port plate, poppet springs, pistons, bearings and other components. Reassembly instructions are also provided, describing how to install components in reverse order and noting precautions for spring loaded parts.
Caterpillar cat 336 d l excavator (prefix jbt) service repair manual (jbt0000...fjskkkdmem
This document provides instructions for removing, disassembling, assembling, and installing the piston motor (hydraulic fan) used in Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor off the machine. Disassembly requires removing multiple components like the head, ports, bearings, pistons, and seals. Assembly is the reverse of disassembly. Installation involves lifting and bolting the piston motor and fan motor assembly back onto the excavator.
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...zatao0179249295
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) of Caterpillar 336D and 336D L excavators. The disassembly process involves removing 15 parts in 13 steps, taking care with spring-loaded components. The assembly process reverses this, involving installing parts in the correct order over 7 pages and 15 steps. Safety precautions are provided to prevent injury from spring forces. Required tools include a bearing puller, retaining ring pliers, and driver group.
The document provides instructions for removing, disassembling, and assembling a piston motor (hydraulic fan) used in Caterpillar 336D and 336D L excavators. The removal procedure involves bending locking tabs, removing bolts and a hub, and lifting the fan motor assembly. The disassembly procedure details removing various components like pins, pistons, bearings, and seals. The assembly procedure is the reverse of disassembly and provides warnings for spring loaded parts. Cleanliness and using new replacement parts for any that are worn or damaged are emphasized.
The document provides instructions for installing and removing a piston motor (hydraulic fan) on a Caterpillar 336D excavator. The summary is:
1. The installation procedure instructs to clean all parts, use a lifting device to position the piston motor and fan motor assembly, and install bolts to secure components.
2. The removal procedure instructs to use lifting devices due to component weights, bend locking tabs, and remove bolts and hubs to detach the piston motor.
3. The disassembly and assembly procedures provide detailed steps and illustrations to disassemble and reassemble the internal components of the piston motor, including springs, seals, bearings, and other parts. Tools are required
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...kesi7153062
The document provides instructions for removing, disassembling, and assembling a piston motor (hydraulic fan) used in Caterpillar 336D and 336D L excavators. The removal procedure involves bending locking tabs, removing bolts and a hub, and lifting the fan motor assembly. The disassembly procedure details removing various components like pins, pistons, bearings, and seals. The assembly procedure is the reverse of disassembly and provides warnings for spring loaded parts. Cleanliness and using new replacement parts for any that are worn or damaged are emphasized.
Caterpillar cat 336 d excavator (prefix jbt) service repair manual (jbt00001 ...fjskemdme
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to remove the fan motor by bending tabs, removing bolts and hub, and lifting the fan motor assembly. It then details disassembling the fan motor by removing the head, port plate, poppet springs, pistons, bearings and other components. Reassembly instructions are also provided, describing how to install components in reverse order and noting any special tools or precautions needed.
Caterpillar cat 336 d excavator (prefix jbt) service repair manual (jbt00001 ...fjskkkdmem
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to remove the fan motor by bending tabs, removing bolts and hub, and lifting the fan motor assembly. It then details disassembling the fan motor by removing the head, port plate, poppet springs, pistons, bearings and other components. Reassembly instructions are also provided, describing how to install components in reverse order and noting any special tools or precautions needed.
Caterpillar cat 336 d l excavator (prefix jbt) service repair manual (jbt0000...fjskemdme
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to remove the fan motor by bending tabs, removing bolts and hub, and lifting the fan motor assembly. It then details disassembling the fan motor by removing the head, port plate, poppet springs, pistons, bearings and other components. Reassembly instructions are also provided, describing how to install components in reverse order and noting precautions for spring loaded parts.
Caterpillar cat 336 d l excavator (prefix jbt) service repair manual (jbt0000...fjskkkdmem
This document provides instructions for removing, disassembling, assembling, and installing the piston motor (hydraulic fan) used in Caterpillar 336D and 336D L excavators. The removal process involves detaching hoses and electrical connections, then lifting the fan motor assembly and piston motor off the machine. Disassembly requires removing multiple components like the head, ports, bearings, pistons, and seals. Assembly is the reverse of disassembly. Installation involves lifting and bolting the piston motor and fan motor assembly back onto the excavator.
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...zatao0179249295
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) of Caterpillar 336D and 336D L excavators. The disassembly process involves removing 15 parts in 13 steps, taking care with spring-loaded components. The assembly process reverses this, involving installing parts in the correct order over 7 pages and 15 steps. Safety precautions are provided to prevent injury from spring forces. Required tools include a bearing puller, retaining ring pliers, and driver group.
The document provides instructions for removing, disassembling, and assembling a piston motor (hydraulic fan) used in Caterpillar 336D and 336D L excavators. The removal procedure involves bending locking tabs, removing bolts and a hub, and lifting the fan motor assembly. The disassembly procedure details removing various components like pins, pistons, bearings, and seals. The assembly procedure is the reverse of disassembly and provides warnings for spring loaded parts. Cleanliness and using new replacement parts for any that are worn or damaged are emphasized.
The document provides instructions for installing and removing a piston motor (hydraulic fan) on a Caterpillar 336D excavator. The summary is:
1. The installation procedure instructs to clean all parts, use a lifting device to position the piston motor and fan motor assembly, and install bolts to secure components.
2. The removal procedure instructs to use lifting devices due to component weights, bend locking tabs, and remove bolts and hubs to detach the piston motor.
3. The disassembly and assembly procedures provide detailed steps and illustrations to disassemble and reassemble the internal components of the piston motor, including springs, seals, bearings, and other parts. Tools are required
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...kesi7153062
The document provides instructions for removing, disassembling, and assembling a piston motor (hydraulic fan) used in Caterpillar 336D and 336D L excavators. The removal procedure involves bending locking tabs, removing bolts and a hub, and lifting the fan motor assembly. The disassembly procedure details removing various components like pins, pistons, bearings, and seals. The assembly procedure is the reverse of disassembly and provides warnings for spring loaded parts. Cleanliness and using new replacement parts for any that are worn or damaged are emphasized.
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...cnp692569
The document provides instructions for installing and removing a piston motor (hydraulic fan) on a Caterpillar 336D excavator. The summary is:
1. The procedure describes removing the fan motor assembly and piston motor, which requires lifting devices due to their weights of 68kg and 23kg respectively.
2. Reinstallation requires cleaning parts, installing the piston motor using bolts and lifting devices, and reattaching the fan motor assembly with hub and bolts.
3. Proper cleaning and inspection of parts is emphasized before installation to prevent problems from lint or damaged components.
The document provides instructions for installing and removing a piston motor (hydraulic fan) on a Caterpillar 336D excavator. The summary is:
1. The installation procedure instructs to clean all parts, use a lifting device to position the piston motor and fan motor assembly, and install bolts to secure components.
2. The removal procedure instructs to use lifting devices due to component weights, bend locking tabs, and remove bolts and hubs to detach the piston motor.
3. Disassembly and assembly procedures provide detailed steps and illustrations to dismantle and rebuild the piston motor, involving springs that require special precautions.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten fasteners to the specified torques.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
This document provides instructions for disassembling and assembling the swing drive of a M316D wheeled excavator. The disassembly procedure involves removing 28 parts from the swing drive housing using various tools. The assembly procedure instructs assembling the parts in reverse order, noting to lubricate bearings and check clearances using a dial indicator.
Caterpillar cat m316 d wheeled excavator (prefix d6w) service repair manual (...ifkkdmdmdm
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant and ensuring proper torque specifications are followed for nuts and bolts. Cleanliness and use of the correct tools are emphasized throughout.
This document provides instructions for disassembling and assembling the swing drive of a M322C wheeled excavator. It describes 28 steps to disassemble the swing drive into individual components such as gears, bearings, seals and housing. It also lists the required tools. The assembly procedure is described in reverse order, with precautions around pressurized springs.
This document provides instructions for disassembling and assembling the swing drive of a M322C wheeled excavator. It describes 28 steps to disassemble the swing drive into individual components such as gears, shafts, bearings, seals and housing. It also lists the required tools. The assembly procedure is described in reverse order, with precautions noted for installing components with spring tension.
Caterpillar Cat 325C FM EXCAVATOR (Prefix Y4P) Service Repair Manual (Y4P0000...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C FM excavator. It lists the required tools and parts. The disassembly procedure involves removing over 30 components of the final drive including sprockets, gears, seals, plates, and housings. Detailed illustrations are provided to show how to remove each part correctly. The assembly procedure is not included.
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...ufs89eodkdmdm
The document provides instructions for assembling a travel motor on an excavator. It details 27 steps including installing seals, springs, pistons and other components into the motor housing. The motor is then installed onto the final drive assembly and excavator frame using bolts. Proper lubrication and torque specifications are emphasized to correctly assemble the travel motor.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It describes 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Precautions are provided to ensure fluids are contained and parts are cleaned before assembly. Tools required are listed. Lubrication and heating of some parts is specified before installation.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold and slip joints.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the cylinder head
The procedures describe draining fluids, removing bolts and hoses, cleaning parts, replacing seals, and torquing fasteners to the specified values. Special tools are listed for many of the removal and installation steps.
This document provides instructions for removing and installing inlet and exhaust valves on a C27 Industrial Engine. It describes:
- Using a valve spring compressor tool to remove the valve springs and valve spring retainers.
- Inspecting the valves and checking the spring force.
- Lubricating the valve stems before installation and compressing the springs with a tool to install the retainers.
- Cautions for wearing protective equipment when working with springs to avoid injury from parts propelled by the springs.
More Related Content
Similar to Caterpillar Cat 336D Excavator (Prefix JBT) Service Repair Manual (JBT00001 and up).pdf
Caterpillar Cat 336D L Excavator (Prefix JBT) Service Repair Manual (JBT00001...cnp692569
The document provides instructions for installing and removing a piston motor (hydraulic fan) on a Caterpillar 336D excavator. The summary is:
1. The procedure describes removing the fan motor assembly and piston motor, which requires lifting devices due to their weights of 68kg and 23kg respectively.
2. Reinstallation requires cleaning parts, installing the piston motor using bolts and lifting devices, and reattaching the fan motor assembly with hub and bolts.
3. Proper cleaning and inspection of parts is emphasized before installation to prevent problems from lint or damaged components.
The document provides instructions for installing and removing a piston motor (hydraulic fan) on a Caterpillar 336D excavator. The summary is:
1. The installation procedure instructs to clean all parts, use a lifting device to position the piston motor and fan motor assembly, and install bolts to secure components.
2. The removal procedure instructs to use lifting devices due to component weights, bend locking tabs, and remove bolts and hubs to detach the piston motor.
3. Disassembly and assembly procedures provide detailed steps and illustrations to dismantle and rebuild the piston motor, involving springs that require special precautions.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten fasteners to the specified torques.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
This document provides instructions for disassembling and assembling the swing drive of a M316D wheeled excavator. The disassembly procedure involves removing 28 parts from the swing drive housing using various tools. The assembly procedure instructs assembling the parts in reverse order, noting to lubricate bearings and check clearances using a dial indicator.
Caterpillar cat m316 d wheeled excavator (prefix d6w) service repair manual (...ifkkdmdmdm
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant and ensuring proper torque specifications are followed for nuts and bolts. Cleanliness and use of the correct tools are emphasized throughout.
This document provides instructions for disassembling and assembling the swing drive of a M322C wheeled excavator. It describes 28 steps to disassemble the swing drive into individual components such as gears, bearings, seals and housing. It also lists the required tools. The assembly procedure is described in reverse order, with precautions around pressurized springs.
This document provides instructions for disassembling and assembling the swing drive of a M322C wheeled excavator. It describes 28 steps to disassemble the swing drive into individual components such as gears, shafts, bearings, seals and housing. It also lists the required tools. The assembly procedure is described in reverse order, with precautions noted for installing components with spring tension.
Similar to Caterpillar Cat 336D Excavator (Prefix JBT) Service Repair Manual (JBT00001 and up).pdf (11)
Caterpillar Cat 325C FM EXCAVATOR (Prefix Y4P) Service Repair Manual (Y4P0000...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C FM excavator. It lists the required tools and parts. The disassembly procedure involves removing over 30 components of the final drive including sprockets, gears, seals, plates, and housings. Detailed illustrations are provided to show how to remove each part correctly. The assembly procedure is not included.
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...ufs89eodkdmdm
The document provides instructions for assembling a travel motor on an excavator. It details 27 steps including installing seals, springs, pistons and other components into the motor housing. The motor is then installed onto the final drive assembly and excavator frame using bolts. Proper lubrication and torque specifications are emphasized to correctly assemble the travel motor.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It describes 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Precautions are provided to ensure fluids are contained and parts are cleaned before assembly. Tools required are listed. Lubrication and heating of some parts is specified before installation.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold and slip joints.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the cylinder head
The procedures describe draining fluids, removing bolts and hoses, cleaning parts, replacing seals, and torquing fasteners to the specified values. Special tools are listed for many of the removal and installation steps.
This document provides instructions for removing and installing inlet and exhaust valves on a C27 Industrial Engine. It describes:
- Using a valve spring compressor tool to remove the valve springs and valve spring retainers.
- Inspecting the valves and checking the spring force.
- Lubricating the valve stems before installation and compressing the springs with a tool to install the retainers.
- Cautions for wearing protective equipment when working with springs to avoid injury from parts propelled by the springs.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap-to-connect fittings, removing and installing a muffler, and removing and installing a fuel priming pump and fuel filter base.
2) The procedures include illustrations showing the components and numbered steps for disassembly and reassembly. Safety warnings are provided at the beginning regarding relieving pressures before disconnection.
3) Torque specifications and required tools are listed for relevant installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 345D L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pins, bearing, and piston assemblies. Special care must be taken to clean parts and ensure they are reinstalled in their original locations. Proper assembly prevents damage and contamination of parts.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 345D L Excavator (Prefix RGD) Service Repair Manual (RGD00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, plates, seals, pins, and piston assemblies. The instructions describe cleaning parts and ensuring they are reinstalled in their original locations to properly reassemble the travel motor.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...ufs89eodkdmdm
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D EXCAVATOR JBT
Configuration: 336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02424411
Piston Pump (Hydraulic Fan) - Install
SMCS - 1387-012-QP; 5070-012-HFN
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01211400
1. Position piston pump (7) and install bolts (6).
2. Connect harness assembly (5).
3. Connect hose assemblies (3) and (4).
1/2
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01211399
4. Connect hose assembly (2).
Illustration 3 g01206719
5. Close door (1).
6. Fill the hydraulic system with oil. Refer to Operation and Maintenance Manual, "Refill
Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 23 09:24:21 UTC+0800 2020
2/2
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D EXCAVATOR JBT
Configuration: 336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415451
Piston Motor (Hydraulic Fan) - Remove
SMCS - 1386-011-QP; 5058-011-FM
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01207415
1. Bend locking tabs (1) backward.
2. Remove bolts (2) and hub (3).
1/2
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g01207416
3. Use a suitable lifting device to position fan motor assembly (4) onto suitable cribbing. The
weight of fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207418
4. Attach a suitable lifting device to piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
5. Remove bolts (6) and fan motor (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 23 09:25:17 UTC+0800 2020
2/2
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D EXCAVATOR JBT
Configuration: 336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415272
Piston Motor (Hydraulic Fan) - Disassemble
SMCS - 1386-015-QP; 5058-015-FM; 5058-015-HFN
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Start By:
a. Remove the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Remove".
1/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01207275
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (1) and head (2).
Illustration 2 g01207276
2. Remove O-ring seal (3), port plate (4), and bearing cup (5).
Illustration 3 g01207278
2/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (6), sleeve (7), poppet (8), spring (9), poppet (10), and O-ring seal (11).
Illustration 4 g01207279
4. Remove bearing cone (12).
Illustration 5 g01207280
5. Remove shim (13) and rotating group (14).
3/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 9 g01207284
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Use Tooling (C) and Tooling (B) in order to remove retaining ring (19).
10. Remove shim (23), spring (22), and shim (21).
Illustration 10 g01207285
11. Remove swashplate (24) and shaft (25).
5/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 11 g01207287
12. Use Tooling (A) in order to remove bearing cone (26) from shaft (25).
Illustration 12 g01207286
13. Use Tooling (C) in order to remove retaining ring (27).
14. Remove lip seal (28).
Illustration 13 g01207288
15. Remove bearing cup (29).
6/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D EXCAVATOR JBT
Configuration: 336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 12 g01207276
15. Lower the temperature of bearing cup (5).
16. Install bearing cup (5), port plate (4), and O-ring seal (3).
Illustration 13 g01207275
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install head (2) and bolts (1).
End By:
a. Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install".
6/7
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D EXCAVATOR JBT
Configuration: 336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415453
Piston Motor (Hydraulic Fan) - Install
SMCS - 1386-012-QP; 5058-012-FM
installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01207418
1. Use a suitable lifting device to install piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
2. Install bolts (6).
1/2
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01207416
3. Use a suitable lifting device to reposition fan motor assembly (4), as shown. The weight of
fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207415
4. Install hub (3) and bolts (2).
5. Bend locking tabs (1) over bolts (2).
End By:
a. Install the fan. Refer to Disassembly and Assembly, "Fan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 23 09:28:04 UTC+0800 2020
2/2
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D EXCAVATOR JBT
Configuration: 336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02554917
Hydraulic Lockout Control - Remove
SMCS - 5001-011-LK
Removal Procedure
Illustration 1 g01187398
1. Remove screws (2) and panel (1).
1/2
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g01278781
2. Remove screws (6). Cut cable strap (8) and place switch (7) aside.
3. Remove bolt (4), bolt (5), and hydraulic lockout control (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 23 09:29:00 UTC+0800 2020
2/2
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D EXCAVATOR JBT
Configuration: 336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378526
Hydraulic Lockout Control - Disassemble
SMCS - 5001-015-LK
Disassembly Procedure
Start By:
a. Remove the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Remove".
Illustration 1 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
1/3
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove retaining rings (1) and lever assembly (2).
2. Remove retaining ring (4), lever assembly (5), and spring (3).
Illustration 2 g01187383
3. Pull back cover (8) in order to remove pin (7) from pipe assembly (6).
Illustration 3 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/3
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 4. Remove pin (10) from pin (9).
5. Remove spring (11) from cover (12).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 23 09:29:56 UTC+0800 2020
3/3
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D EXCAVATOR JBT
Configuration: 336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378527
Hydraulic Lockout Control - Assemble
SMCS - 5001-016-LK
Assembly Procedure
Illustration 1 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/3
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 1. Install spring (11) to cover (12).
2. Install pin (10) to pin (9).
Illustration 2 g01187383
3. Install pin (7) to pipe assembly (6).
4. Slide cover (8) over pipe assembly (6).
Illustration 3 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Install spring (3), lever assembly (5), and retaining ring (4).
2/3
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 6. Install lever assembly (2) and retaining rings (1).
End By:
a. Install the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 23 09:30:52 UTC+0800 2020
3/3
336D & 336D L Excavators JBT00001-UP (MACHINE) POWERED BY C9 Engine(...
2020/8/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...