Caterpillar Cat 336 GC Excavator (Prefix EBJ) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
336 GC Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336 GC EXCAVATOR EBJ
Configuration: 336 GC Excavator EBJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
336 Excavator Machine Systems
Media Number -M0087649-02 Publication Date -01/10/2018 Date Updated -22/10/2018
i05103849
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
D 5P-3931 Anti-Seize Compound -
E 1U-9895 Crossblock 1
F 6V-2012 Depth Micrometer 1
G 6V-7059 Micrometer () 1
H - Loctite 242 -
J 6V-2055 Grease -
K - Loctite 17430 -
L 8T-9206 Seal Installer 1
1/12
336 GC Excavator EBJ00001-UP (MACHINE) POWERED BY C7.1 Engine(M00904...
2020/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

Illustration 1 g02132155
1. Apply Tooling (D) to the surface of dowels (46) . Install dowels (46) .
2. Raise the temperature of roller bearing (47) . Install the roller bearing (47) on motor housing
(48) .
3. Install Duo-Cone seal (45) .
4. Lower the temperature of bearing races (43) . Install bearing races (43) in sprocket housing
(41) .
5. Install Duo-Cone seal (44) .
2/12
2020/9/9

6. Attach Tooling (C) and a suitable lifting device to sprocket housing (41) . The weight of
sprocket housing (41) is approximately 107 kg (235 lb). Install sprocket housing (41) .
7. Raise the temperature of roller bearing (42) . Install the roller bearing (42) .
3/12
2020/9/9

8. Use Tooling (E) and a suitable press in order to apply force to roller bearing (42) . Apply a
force of 4000 kg (8818 lb) to the top of Tooling (E) . Rotate sprocket housing (41) in order
to seat the roller bearings.
9. Reduce the force on top of Tooling (E) to 3000 ± 300 kg (6614 ± 661 lb). Use Tooling (F)
in order to measure Dimension (X) . Record Dimension (X) .
4/12
2020/9/9

10. Use Tooling (F) in order to measure Dimension (W) on gear (39) . Record Dimension (W) .
11. Remove Tooling (E) .
5/12
2020/9/9

12. Subtract Dimension (X) from Dimension (W) and record the difference as Dimension (V) .
The correct shim thickness is Dimension (V) . Use Tooling (G) in order to measure the
correct thickness of shims (40) . The tolerance of Dimension (V) is 0 ± 0.05 mm (0 ± 0.002
inch).
Note: Use a maximum of two shims (40) . If two shims (40) are used to achieve the proper
dimension, install the thinner of the two shims toward gear (39) .
13. Install shims (40) .
14. Apply Tooling (G) to the threads of bolts (38) . Install gear (39) and bolts (38) . Tighten
bolts (38) to a torque of 900 ± 100 N·m (665 ± 75 lb ft).
6/12
2020/9/9

Note: Make sure that the spring pin hole in planetary shaft (32) is aligned with the spring
pin hole in the carrier.
15. Install roller bearings (35) , planetary gear (36) , washer (37) , washer (33) , planetary shaft
(32) , and spring pin (31) into carrier assembly (34) . Install spring pin (31) until spring pin
(31) is even with the outside surface of the carrier. Align the split in spring pin (31) to the
top or the bottom.
16. Make a stake mark on each side of the spring pin hole in the carrier, as shown. The stake
mark will prevent the spring pin from falling out of the spring pin hole. Make a stake mark
at Dimension (Y) . Dimension (Y) is 2.25 ± 0.75 mm (0.089 ± 0.030 inch).
17. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (30) . The
weight of planetary gear assembly (30) is approximately 57 kg (125 lb). Install planetary
gear assembly (30) .
18. Install O-ring seal (29) .
7/12
2020/9/9

19. Attach Tooling (A) and a suitable lifting device to ring gear (27) . The weight of ring gear
(27) is approximately 70 kg (155 lb). Install ring gear (27) and bolts (28) . Tighten bolts
(28) to a torque of 520 ± 70 N·m (385 ± 52 lb ft).
20. Install spacer (26) .
8/12
2020/9/9

21. Install roller bearing (22) , planetary gear (23) , washer (24) , washer (20) , planetary shaft
(18) , and spring pin (17) into carrier assembly (21) . Install spring pin (17) until spring pin
(17) is even with the outside surface of the carrier. Align the split in spring pin (17) to the
top or the bottom.
22. Make a stake mark on each side of the spring pin hole in the carrier, as shown. The stake
mark will prevent the spring pin from falling out of the spring pin hole. Make a stake mark
at Dimension (Y) . Dimension (Y) is 2.25 ± 0.75 mm (0.089 ± 0.030 inch).
23. Install sun gear (25) and retaining ring (19) .
24. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (15) . The
weight of planetary gear assembly (15) is approximately 32 kg (70 lb). Install planetary gear
assembly (15) .
25. Install spacer (16) .
9/12
2020/9/9

26. Install sun gear (14) and retaining ring (10) .
27. Install washer (12) , roller bearing (11) , planetary gear (9) , washer (8) , and retaining ring
(7) on carrier assembly (13) .
28. Install planetary gear assembly (6) , spacer (5) , and sun gear (4) .
10/12
2020/9/9

29. Use the correct plate (3) in order to achieve Dimension (Z) . Dimension (Z) is 1.00 to 2.00
mm (0.039 ± 0.079 inch).
11/12
2020/9/9

30. Use Tooling (J) in order to secure plate (3) in cover (2) .
31. Apply Tooling (K) to the mating surface of cover (1) . Attach Tooling (A) and a suitable
lifting device to cover (2) . The weight of cover (2) is approximately 20 kg (45 lb). Install
cover (2) and bolts (1) . Tighten bolts (1) to a torque of 105 ± 20 N·m (80 ± 15 lb ft).
32. Remove Tooling (A) and the suitable lifting device. Apply Tooling (H) to the threads of the
set screws. Install the set screws so that the setscrews are flush with cover (1) .
End By: Install the final drive and the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 9 10:05:07 UTC+0800 2020
12/12
2020/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07223777
Swivel - Remove and Install
SMCS - 5060-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5473 Lifting Eye Assembly 2
B 8C-8422 Sealant -
C - LOCTITE 243 -
Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" M0066576.
1. Drain hydraulic fluid. Refer to operation maintenance manual hydraulic system oil change
M0068104.
1/9
2020/9/9

2/9
2020/9/9

3/9
2020/9/9

4/9
2020/9/9

5/9
2020/9/9

6/9
2020/9/9

7/9
2020/9/9

Installation Procedure
1. Install swivel in the reverse order of removal.
8/9
2020/9/9

Wed Sep 9 10:06:03 UTC+0800 2020
9/9
2020/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07223810
Swivel - Disassemble
SMCS - 5060-015
Disassemble Procedure
Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" , M0066576.
1/4
2020/9/9

2/4
2020/9/9

3/4
2020/9/9

Wed Sep 9 10:06:58 UTC+0800 2020
4/4
2020/9/9

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07223813
Swivel - Assemble
SMCS - 5060-016
Assemble Procedure
Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" , M0066576.
1/4
2020/9/9

Caterpillar Cat 336 GC Excavator (Prefix EBJ) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 336 GC Excavator (Prefix EBJ) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 336 GC Excavator (Prefix EBJ) Service Repair Manual Instant Download.pdf (12)

More from 8foskkdjdkdm3e

More from 8foskkdjdkdm3e (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 336 GC Excavator (Prefix EBJ) Service Repair Manual Instant Download.pdf