The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00894497
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2244 Pump Extractor 1
B 6V-4186 Fuel Pump Timing Pin 1
C 8T-5287 Wrench 1
D
6V-9128 Rack Position Tool Group
1
3S-3270 Indicator Contact Point 1
C-clamp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00507964
1. Install spacer (1) in the fuel injection pump housing.
Illustration 2 g00507989
Illustration 3 g00508002
2. Install Tool (B) in the fuel injection pump housing. Move the rack until Tool (B) can be
installed in order to hold the rack in the center position. The rack must be in the center
position in order to install the fuel injection pumps.
2/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 3. Turn the camshaft until the lobe of the camshaft is downward so that the fuel injection pump
can be installed.
4. Install Tool (A) on the bonnet of the fuel injection pump.
5. Install the fuel injection pump in the fuel injection pump housing. Ensure that slot (3) that is
cut in the gear is aligned with the small pin (2) and groove (4) in the barrel. The small pin
(2) and groove (4) in the barrel are aligned with dowel (5) in the fuel injection pump
housing.
Illustration 4 g00508005
6. Put clean engine oil on O-ring seal (6) and install the O-ring seal in the fuel injection pump
housing.
Illustration 5 g00508057
7. Install bushing (7) by hand until the bushing is even with the top of the fuel injection pump
housing. If bushing (7) cannot be installed by hand, remove bushing (7). Remove the fuel
injection pump. Put the pump in alignment and reinstall bushing (7) .
8. Install Tool (C) on bushing (7) and tighten the bushing to a torque of 163 ± 14 N·m (120 ±
10 lb ft).
3/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 9. Install Tool (D) in order to measure the total travel of the rack. The correct travel for the
rack is 15.70 mm (.618 inch). A smaller measurement is an indication of improper fuel
injection pump installation.
10. Repeat Steps 1 through 9 in order to install the remaining fuel injection pumps.
11. Install the cover and the gasket on the fuel injection pump housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:13:16 UTC+0800 2020
4/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01117604
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 1 g00537468
1. Remove bolt (2) and the clamp that holds the oil supply tube and the oil drain tube in
position.
2. Remove two bolts (1) that hold the oil supply tube to the turbocharger. Remove two bolts
(3) that hold the oil drain tube to the turbocharger.
3. On the 3304B, loosen the two hose clamps and remove the hose from the turbocharger.
Slide the hose onto the pipe that goes to the cylinder head.
4. Loosen nut (4) and remove the oil supply tube from the engine.
Illustration 2 g00537495
5. Loosen four bolts (6) and the nuts that hold turbocharger (5) to the exhaust manifold.
Remove turbocharger (5) and the gasket from the exhaust manifold. Remove oil drain tube
(7) from the engine and check the O-ring seal for damage. If the O-ring seal is worn or
damaged, use a new part for replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:14:12 UTC+0800 2020
2/2(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01009195
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-6363 Turbocharger Fixture Group 1
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g00517570
1. Install the turbocharger onto Tool (A) .
2. Apply alignment marks to the two housings and the cartridge assembly for correct
alignment during assembly.
3. Loosen clamp (3) and remove compressor housing (4) from cartridge assembly (2) .
4. Loosen the remaining clamp on turbine housing (1) and remove cartridge assembly (2) from
the turbine housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:15:07 UTC+0800 2020
2/2(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01009564
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-6363 Turbocharger Fixture Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 1 g00517570
1. Put cartridge assembly (2) in position on turbine housing (1). Make sure that the
identification marks are in alignment. Tighten the clamp that secures cartridge assembly (2)
to turbine assembly (1) to a torque of 14 ± 1.1 N·m (125 ± 10 lb in).
2. Put compressor housing (4) in position on cartridge assembly (2). Make sure that the
identification marks are in alignment. Tighten clamp (3) that secures compressor housing
(4) to cartridge assembly (2) to a torque of 14 ± 1.1 N·m (125 ± 10 lb in).
3. Remove the turbocharger from Tool (A) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:16:03 UTC+0800 2020
2/2(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01117656
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00537495
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets or the O-ring
seals are worn or damaged, use new parts for replacement.
1/2(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 1. Install oil drain tube (7) on the engine. Position the gasket and turbocharger (5) on top of the
exhaust manifold and install four bolts (6) and the nuts.
Illustration 2 g00537468
2. Install the gasket and two bolts (3) that hold the oil drain tube to the turbocharger. Put the
oil supply tube in position and install the gasket and two bolts (1) that hold the oil supply
tube to the turbocharger. Tighten nut (4) .
3. On the 3304B, slide the hose into position on the turbocharger and the pipe that goes to the
cylinder head. Tighten the hose clamp.
4. Install the clamp that holds the oil supply tube and the oil drain tube in position and install
bolt (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:16:59 UTC+0800 2020
2/2(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01041426
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00537836
1/5(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. 1. Remove two nuts (1), the washers and the heat shield from the exhaust manifold.
Illustration 2 g00537855
2. Remove bolt (3) from the bracket that holds two of the fuel injection lines in position.
Loosen nuts (2) and (4) and remove the two fuel injection lines from the engine. Put
protective caps on the fuel injectors and put protective caps on the fuel injection pump in
order to prevent contamination.
Illustration 3 g00537885
3. Remove the remaining ten exhaust manifold nuts (5) and the large washers. Remove
exhaust manifold (6).
2/5(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 4 g00541058
4. Remove three exhaust manifold gaskets (7) from the cylinder head and the twelve exhaust
manifold studs, if necessary. Make sure that the position of the two longer studs are marked
for proper installation.
Installation Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 5P-0144 Fuel Line Socket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. If the twelve exhaust manifold studs were removed, apply 5P-3931 Anti-Seize Compound
to both ends of the exhaust manifold studs and install the studs in the cylinder head. Make
sure that the two longer studs are installed in the correct position. Tighten the studs to a
torque of 27 ± 4 N·m (20 ± 3 lb ft).
3/5(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 5 g00541058
2. Put three exhaust manifold gaskets (7) in position on the cylinder head.
Illustration 6 g00537885
3. Install exhaust manifold (6). Install ten washers and nuts (5). The two longer studs are for
the installation of the heat shield. Tighten exhaust manifold nuts (5) to a torque of 47 ± 4
N·m (35 ± 3 lb ft).
Illustration 7 g00537855
4/5(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 4. Remove the protective caps from the fuel injectors and the fuel injection pump. Put the fuel
injection lines in position and tighten nuts (2) and (4) finger tight. Install bolt (3) in the
bracket that holds the fuel injection lines in position. Tighten nuts (3) and (4) with Tool (A)
to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
Illustration 8 g00537836
5. Install the two large washers and the spacers on the two remaining exhaust manifold studs.
Install heat shield (1) and the remaining two washers and exhaust manifold nuts that fasten
heat shield (1) to the exhaust manifold. Tighten the two nuts to a torque of 47 ± 4 N·m (35 ±
3 lb ft).
6. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel system -
Prime" topic (Maintenance Section).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:17:55 UTC+0800 2020
5/5(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00962627
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 8S-2263 Valve Spring Tester 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and assembly, "Cylinder Head - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 1 g00490614
1. Use Tool (A) to compress valve spring (2) and remove valve keepers (1) .
2. Remove Tool (A), the rotocoil, the valve spring and the valve stem oil shield. Remove the
valve from the cylinder head. Put identification marks on the valves for installation
purposes.
Illustration 2 g00490682
3. Check the valve spring force with Tool (B). Refer to Specifications, "Cylinder Head
Valves" for information on the valve springs.
4. Perform Steps 1 through 3 for the remaining inlet and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 5S-1322 Valve Keeper Inserter 1
2/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate the inlet and exhaust valves with clean engine oil. Install the inlet and exhaust
valves in the original location in the cylinder head.
Illustration 3 g00508681
2. Install valves (3), oil shield (4), valve spring (2) and rotocoil (1) in the cylinder head.
Illustration 4 g00490777
3. Use Tool (A) to compress valve spring (2). Install valve keeper (5) on the valve stem with
Tool (B) .
3/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
4. Carefully remove Tool (A). Strike the top of the valve with a soft faced hammer in order to
ensure that the valve keepers are properly installed.
5. Repeat Steps 3 through 4 for the remaining inlet and exhaust valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove
and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:18:50 UTC+0800 2020
4/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00962891
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7349 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 1 g00490787
1. Use Tool (A) to remove the inlet and exhaust valve guides from the cylinder head.
2. Repeat Step 1 for the remaining inlet and exhaust valve guides.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-7349 Valve Guide Driver 1
B 9U-6954 Valve Guide Collar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 2 g00490790
1. Put clean engine oil on the outside diameter of the valve guide. Install the valve guide with
Tool (A) and Tool (B), as shown.
Illustration 3 g00508601
2. Dimension (X) from the top of the valve guide to the cylinder head must be 22.23 ± 0.25
mm (0.875 ± 0.010 inch). For more information on the inlet and exhaust valve guides, refer
to Specifications, "Cylinder Head Valves".
Note: In order to help prevent damage to the valve guides, Tool (B) must be used during
installation.
3. Repeat Steps 1 and 2 for the remaining inlet and exhaust valve guides.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:19:46 UTC+0800 2020
3/3(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02107684
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4805 Valve Seat Extractor Tool Group 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 1 g00490857
1. Use Tooling (A) in order to remove the valve seat insert from the cylinder head.
2. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
3. Repeat Steps 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 6V-4805 Valve Seat Extractor Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...