This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, seals, and other internal components. Technicians are instructed to mark components for alignment during reassembly and to contain any fluids removed.
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...ifoseidkkd
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean parts thoroughly, apply identification marks, and be careful not to damage mating surfaces when taking the motor apart.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and handling pressurized systems.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean and mark components for reassembly. Safety notices advise containing fluids and disposing of them properly.
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...ifoseidkkd
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean and mark components for reassembly. Safety notices advise containing fluids and disposing of them properly.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and handling pressurized systems.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...ifoseidkkd
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean parts thoroughly, apply identification marks, and be careful not to damage mating surfaces when taking the motor apart.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and handling pressurized systems.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean and mark components for reassembly. Safety notices advise containing fluids and disposing of them properly.
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...ifoseidkkd
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean and mark components for reassembly. Safety notices advise containing fluids and disposing of them properly.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and handling pressurized systems.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean and mark components for alignment during reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean and mark components for alignment during reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Safety notices are included to contain fluids and dispose of them properly when disassembling components.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean parts thoroughly, apply identification marks, and be careful not to damage mating surfaces when taking the motor apart.
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...JayHaines2
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean parts and apply identification marks to ensure correct reassembly. Safety notices advise containing fluids and disposing of them properly.
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...fjskkmemem
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators in 3 steps:
1. Clean and mark the travel motor components for assembly reference before removing bolts and separating parts.
2. Disassemble the head, brake assembly, barrel assembly, and shaft from the travel motor body while keeping matched parts together.
3. Remove seals, plates, springs and other individual parts, noting their locations for reassembly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators in 3 steps:
1. Clean and mark the travel motor components for assembly reference before removing bolts and separating parts.
2. Disassemble the head, brake assembly, barrel assembly, and shaft from the travel motor body while keeping matched parts together.
3. Remove seals, plates, springs and other individual parts, noting their locations for reassembly.
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...fjskkmemem
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators in 3 steps:
1. Clean and mark the travel motor components for assembly reference before removing parts.
2. Remove components like the head, fittings, seals, plates, and shaft from the travel motor body.
3. Disassemble further components like the barrel assembly, piston shoe assemblies, springs and seals from removed parts.
Care and identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...JayHaines2
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Proper identification and alignment of components is emphasized to ensure correct reassembly. Safety notices recommend cleaning components and containing fluids during disassembly.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined, such as containing fluids and wearing proper protective equipment.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Proper identification and alignment of components is emphasized to ensure correct reassembly. Safety notices advise containing fluids and disposing of them properly.
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...fujsekksmem
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Proper identification and alignment of components is emphasized to ensure correct reassembly. Safety notices advise containing fluids and disposing of them properly.
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor which involve installing components like the shaft assembly, cam plate, barrel assembly, brake piston and head in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar cat 325 b track type excavator (prefix 8pr) service repair manual...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor, assembling the components in reverse order and ensuring proper installation of seals, plates and alignment of parts. Safety notices are provided to properly contain fluids and avoid damage to components.
Caterpillar Cat 390F L Excavator (Prefix FEH) Service Repair Manual (FEH00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves 40 steps to disassemble the various components of the travel motor including removing seals, springs, plates, pistons, and bearings. The assembly section outlines 31 steps to reinstall these components in reverse order while ensuring proper cleaning and alignment of parts. Precision tools are required and safety precautions mentioned to avoid injury from spring forces.
Caterpillar Cat 374D L Excavator (Prefix PJA) Service Repair Manual (PJA00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 374D L Excavator. It describes 34 steps to disassemble the final drive by removing components like the ring gear, carrier assemblies, gears, shafts and seals. It then describes 8 steps for assembling the final drive, which involves cleaning parts, pressing in bearings and pins, installing housings and determining the correct shim number based on bearing preload measurements. The document contains detailed illustrations and lists required tools for each step.
Este documento contiene instrucciones para operar y mantener una máquina. Explica los números de la máquina, las señales de seguridad, cómo subirse y bajarse de la máquina, cómo operar la estación del operador, cómo conducir y operar la máquina, cómo transportarla, el mantenimiento requerido y las especificaciones técnicas.
Caterpillar Cat 374F L Excavator (Prefix DNM) Service Repair Manual (DNM00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install over 35 individual parts. Key steps include removing the ring gear, carrier assemblies, gears and shafts, and separating the main housing from the motor housing. Proper cleaning and application of sealant is emphasized throughout reassembly.
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It emphasizes cleaning parts and marking components to ensure proper reassembly.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix GPH) Service Repair Manual...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor of a 345C L Hydraulic Excavator. The disassembly procedure involves 31 steps to remove components like the head, plates, disks, rotating group, seals and more. The assembly procedure involves 13 steps and notes to clean parts, apply lubricant, set proper measurements and orientations when reinstalling components like the washers, spacers and seals. Special tools are listed for tasks like removing bearings and installing seals.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble parts like the head, plates, seals, pistons, and housing. It then lists 27 steps to reassemble these parts in reverse order, making sure to clean parts and apply lubricant. Proper installation of seals, washers, and keys is emphasized.
More Related Content
Similar to Caterpillar Cat 325L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM00001 and up) 1.pdf
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean and mark components for alignment during reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean and mark components for alignment during reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Safety notices are included to contain fluids and dispose of them properly when disassembling components.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean parts thoroughly, apply identification marks, and be careful not to damage mating surfaces when taking the motor apart.
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...JayHaines2
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs and other components. Technicians are instructed to clean parts and apply identification marks to ensure correct reassembly. Safety notices advise containing fluids and disposing of them properly.
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...fjskkmemem
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators in 3 steps:
1. Clean and mark the travel motor components for assembly reference before removing bolts and separating parts.
2. Disassemble the head, brake assembly, barrel assembly, and shaft from the travel motor body while keeping matched parts together.
3. Remove seals, plates, springs and other individual parts, noting their locations for reassembly.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators in 3 steps:
1. Clean and mark the travel motor components for assembly reference before removing bolts and separating parts.
2. Disassemble the head, brake assembly, barrel assembly, and shaft from the travel motor body while keeping matched parts together.
3. Remove seals, plates, springs and other individual parts, noting their locations for reassembly.
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...fjskkmemem
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators in 3 steps:
1. Clean and mark the travel motor components for assembly reference before removing parts.
2. Remove components like the head, fittings, seals, plates, and shaft from the travel motor body.
3. Disassemble further components like the barrel assembly, piston shoe assemblies, springs and seals from removed parts.
Care and identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...JayHaines2
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Proper identification and alignment of components is emphasized to ensure correct reassembly. Safety notices recommend cleaning components and containing fluids during disassembly.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined, such as containing fluids and wearing proper protective equipment.
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Proper identification and alignment of components is emphasized to ensure correct reassembly. Safety notices advise containing fluids and disposing of them properly.
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...fujsekksmem
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Proper identification and alignment of components is emphasized to ensure correct reassembly. Safety notices advise containing fluids and disposing of them properly.
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor which involve installing components like the shaft assembly, cam plate, barrel assembly, brake piston and head in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar cat 325 b track type excavator (prefix 8pr) service repair manual...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor, assembling the components in reverse order and ensuring proper installation of seals, plates and alignment of parts. Safety notices are provided to properly contain fluids and avoid damage to components.
Similar to Caterpillar Cat 325L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM00001 and up) 1.pdf (14)
Caterpillar Cat 390F L Excavator (Prefix FEH) Service Repair Manual (FEH00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves 40 steps to disassemble the various components of the travel motor including removing seals, springs, plates, pistons, and bearings. The assembly section outlines 31 steps to reinstall these components in reverse order while ensuring proper cleaning and alignment of parts. Precision tools are required and safety precautions mentioned to avoid injury from spring forces.
Caterpillar Cat 374D L Excavator (Prefix PJA) Service Repair Manual (PJA00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 374D L Excavator. It describes 34 steps to disassemble the final drive by removing components like the ring gear, carrier assemblies, gears, shafts and seals. It then describes 8 steps for assembling the final drive, which involves cleaning parts, pressing in bearings and pins, installing housings and determining the correct shim number based on bearing preload measurements. The document contains detailed illustrations and lists required tools for each step.
Este documento contiene instrucciones para operar y mantener una máquina. Explica los números de la máquina, las señales de seguridad, cómo subirse y bajarse de la máquina, cómo operar la estación del operador, cómo conducir y operar la máquina, cómo transportarla, el mantenimiento requerido y las especificaciones técnicas.
Caterpillar Cat 374F L Excavator (Prefix DNM) Service Repair Manual (DNM00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install over 35 individual parts. Key steps include removing the ring gear, carrier assemblies, gears and shafts, and separating the main housing from the motor housing. Proper cleaning and application of sealant is emphasized throughout reassembly.
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It emphasizes cleaning parts and marking components to ensure proper reassembly.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix GPH) Service Repair Manual...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor of a 345C L Hydraulic Excavator. The disassembly procedure involves 31 steps to remove components like the head, plates, disks, rotating group, seals and more. The assembly procedure involves 13 steps and notes to clean parts, apply lubricant, set proper measurements and orientations when reinstalling components like the washers, spacers and seals. Special tools are listed for tasks like removing bearings and installing seals.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble parts like the head, plates, seals, pistons, and housing. It then lists 27 steps to reassemble these parts in reverse order, making sure to clean parts and apply lubricant. Proper installation of seals, washers, and keys is emphasized.
This document provides instructions for disassembling and assembling the swing drive of a 340F Excavator. The disassembly procedure involves removing 27 parts from the swing drive including the cover, sun gear, carrier assembly, planetary gears, ring gear, pinion shaft, and bearings. The assembly procedure instructs installing lip seals and bearings on the cage and pinion shaft before lowering the cage over the pinion shaft and installing the bearing.
This document provides instructions for removing and installing an exhaust manifold and inlet and exhaust valves on a 325-A FM L EXCAVATOR 7LM. It describes:
1) Removing the bolts, exhaust manifold, and gaskets from the cylinder head to remove the exhaust manifold.
2) Installing new gaskets and mounting the exhaust manifold to the cylinder head, applying anti-seize compound and torqueing bolts.
3) Removing inlet and exhaust valves by compressing springs, removing retainers and springs, and removing seals and valves.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar Cat 385C L Excavator (Prefix T2E) Service Repair Manual (T2E00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. The assembly process reverses the disassembly steps and provides additional details on cleaning, lubricating, and setting bearing preloads using shims. Proper tools and lifting devices are required due to the large size and weight of many components. Cleanliness is emphasized throughout to prevent damage to precision parts from contaminants.
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure details cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash. Proper removal and installation is important to avoid engine damage.
This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves over 40 steps to fully disassemble the travel motor by removing components like the head, relief valves, pistons, plates, seals, bearings, and housing. Special tools are required and safety precautions must be followed when removing spring-loaded or heavy parts. The assembly process reverses the disassembly steps and requires cleaning and lubricating parts before reinstallation.
Caterpillar Cat 385C L Excavator (Prefix EDA) Service Repair Manual (EDA00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and parts. The disassembly process involves removing over 30 components from the final drive housing in a specific sequence, including carrier assemblies, sun gears, planetary gear sets, and seals. The assembly process reverses the disassembly steps and provides notes on cleaning, inspecting, lubricating, and installing replacement parts as needed.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325-A FM L EXCAVATOR 7LM
Configuration: 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
325, 325B and 325L Excavators
Media Number -RENR1178-03 Publication Date -01/09/2000 Date Updated -09/10/2001
i01765040
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure For The Travel Motor On CIPI
Undercarriage Arrangements Which Are Based On 325
Track Type Excavators
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in
this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel
motor to a suitable holding fixture in a vertical position. The weight of the travel motor is
approximately 71 kg (157 lb).
1/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the travel motor
body.
Illustration 1 g00510326
3. Remove nine socket head bolts (1) and head (2) from the travel motor body.
Note: During the removal of head (2) from the travel motor body, be careful not to damage
the mating surfaces of the components.
Illustration 2 g00510341
2/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g00510349
4. Turn over head (2). Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from
the head. Remove the two check valve assemblies from the head.
Note: There is a retainer that is located under spring (9). This retainer is a press fit in head
(2). Do not remove the retainer.
5. Insert a dowel rod with a small diameter into hole "X". Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
Illustration 4 g00510351
6. Remove three fittings (10) and four plugs (11) from the head. Remove the O-ring seal from
each fitting.
3/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 5 g00510352
7. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
8. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port "Y". Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the travel motor body.
Illustration 6 g00510353
9. Remove O-ring seals (15) and (17), and backup rings (16) and (18) from the brake piston.
4/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 7 g00510356
10. Remove piston guide (19), three friction plates and three steel plates (20) from the travel
motor body.
Illustration 8 g00510359
11. Remove O-ring seal (21) and backup ring (22) from the piston guide.
Illustration 9 g00510365
5/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
12. Use two large screwdrivers and slowly remove barrel assembly (23) from the travel motor
body, as shown. Do not allow the components to fall apart.
Illustration 10 g00510502
13. Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately. Prior to
the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
14. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
Illustration 11 g00510504
15. Remove guide (27), spacer (28) and nine springs (29) from the barrel.
6/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 12 g00510547
16. Remove cam plate (30) from the travel motor body.
Illustration 13 g00919084
17. Put identification marks on two balls (31) and two keys (32) in the travel motor body for
assembly purposes. Remove two balls (31) and two keys (32) from the travel motor body.
7/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 14 g00510551
18. Remove O-ring seal (33) from the travel motor body.
19. Use a soft faced hammer to remove shaft assembly (34) from the travel motor body.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 33.
Illustration 15 g00510595
20. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 16 g00510598
21. Remove inner race (37) from shaft (34) .
8/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 17 g00510599
22. Remove lip type seal (38) from the travel motor body.
Illustration 18 g00510605
Illustration 19 g00918957
23. Remove two cam plate tension adjusters from the travel motor body. Loosen two nuts (39).
Remove two adjusters (40), two springs (43), and two pistons (44) from the travel motor
body.
9/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 24. Remove O-ring seal (42) and backup ring (41) from each adjuster (40) .
Disassembly Procedure For The Travel Motor On CIPI
Undercarriage Arrangements Which Are Based On 325B
Track Type Excavators
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in
this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel
motor to a suitable holding fixture in a vertical position. The weight of the travel motor is
approximately 50 kg (110 lb).
2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the travel motor
body.
10/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 20 g00510326
3. Remove ten socket head bolts (1) and head (2) from the travel motor body.
Note: During the removal of head (2) from the travel motor body, be careful not to damage
the mating surfaces of the components.
Illustration 21 g00510341
Illustration 22 g00510349
4. Turn over head (2). Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from
the head. Remove the two check valve assemblies from the head.
Note: There is a retainer that is located under spring (9). This retainer is a press fit in head
(2). Do not remove the retainer.
5. Insert a dowel rod with a small diameter into hole "X". Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
11/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 23 g00510351
6. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 24 g00510352
7. Remove three O-ring seals (12) and washer set (13) from the travel motor body.
8. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port "Y". Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the travel motor body.
12/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 25 g00510353
9. Remove O-ring seals (15) and (17) from the brake piston. Remove backup rings (16) and
(18) from the brake piston.
Illustration 26 g00510356
10. Remove piston guide (19), five friction plates (20) and the four steel plates from the travel
motor body.
Illustration 27 g00510359
13/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 11. Remove O-ring seal (21) and backup ring (22) from the piston guide.
Illustration 28 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
12. Use two large screwdrivers and slowly remove barrel assembly (23) from the travel motor
body, as shown. Do not allow the components to fall apart.
Illustration 29 g00510502
13. Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately. Prior to
the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
14. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
14/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 30 g00510504
15. Remove guide (27), spacer (28) and nine springs (29) from the barrel.
Illustration 31 g00510547
16. Remove cam plate (30) from the body of the travel motor.
15/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 32 g00510550
17. Remove two keys (31) and the two locating pins (not shown) from the travel motor body.
Illustration 33 g00510551
18. Remove O-ring seal (33) from the travel motor body.
19. Use a soft faced hammer to remove shaft assembly (34) from the travel motor body.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 33.
Illustration 34 g00510595
20. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
16/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 35 g00510598
21. Remove inner race (37) from shaft (34) .
Illustration 36 g00510599
22. Remove lip type seal (38) from the travel motor body.
Illustration 37 g00510605
17/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. 23. Remove two cam plate tension adjusters from the travel motor body. Loosen two nuts (39).
Remove two adjusters (40), two springs (43), and two pistons (44) from the travel motor
body.
24. Remove O-ring seal (42) and backup ring (41) from each adjuster (40) .
Disassembly Procedure For The Travel Motor On CIPI
Undercarriage Arrangements Which Are Based On 325C
Track Type Excavators
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in
this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
18/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 38 g00510326
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 39 g00510341
Illustration 40 g00510349
19/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 6. Turn over head (2) .
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into Hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8), and seat (7) from the head.
Illustration 41 g00510351
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 42 g00878239
11. Remove O-ring seals (13) and washer set (12) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
20/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
Illustration 43 g00878248
13. Remove O-ring seal (16) from the brake piston. Remove backup ring (15) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
Illustration 44 g00510356
15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of
the travel motor.
21/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 45 g00510359
16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
Illustration 46 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
22/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 47 g00878253
Note: Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately.
Prior to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
Illustration 48 g00510504
19. Remove guide (27), spacer (28), and springs (29) from the barrel.
23/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 49 g00510547
20. Remove cam plate (30) from the body of the travel motor.
Illustration 50 g00510550
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
Illustration 51 g00510551
24/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. 22. Remove O-ring seal (33) from the body of the travel motor.
23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 51.
Illustration 52 g00510595
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 53 g00510598
25. Remove inner race (37) from shaft (34) .
25/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Illustration 54 g00510599
26. Remove lip seal (38) from the body of the travel motor.
Illustration 55 g00510605
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 6 11:21:23 UTC+0800 2020
26/26
325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG...
2020/8/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...