The document provides instructions for removing and installing a flywheel, flywheel housing, and crankshaft rear seal on a Caterpillar 320D2 L excavator engine. The flywheel removal procedure involves removing bolts and installing guide studs to lift the flywheel off. The crankshaft rear seal is replaced as a sealed assembly using a torque wrench. Reinstalling the flywheel housing and flywheel follows the reverse of the removal processes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR WBF
Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780443
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
1/2 inch - UNF by 4 inch
2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Illustration 1 g01336668
Typical example
1. Remove bolts from Position (X) from flywheel (1).
2. Install Tooling (A) in Position (X) to flywheel (1).
3. Install a suitable lifting device onto flywheel (1). Support the weight of the flywheel. The
flywheel can weigh 71 kg (156 lb).
4. If necessary, remove bolts (2) that secure the housing for pilot bearing (3) to flywheel (1).
Remove the housing for pilot bearing (3).
5. Remove remaining bolts (4).
6. Use the lifting device to remove the flywheel from the engine.
2/3(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Illustration 2 g01336669
Typical example
7. Inspect flywheel (1) and ring gear (5) for wear and damage. Replace any worn components
or damaged components.
8. To remove flywheel ring gear (5), follow Step 8.a through Step 8.b.
a. Place the flywheel assembly on a suitable support.
b. Use a hammer and a punch in order to remove ring gear (5) from flywheel (1).
Note: Identify the orientation of the teeth on the flywheel ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:13:37 UTC+0800 2020
3/3(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR WBF
Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780442
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
1/2 inch - UNF by 4 inch
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Illustration 1 g01336671
Typical example
Always wear protective gloves when handling parts that have been
heated.
1. If the flywheel ring gear was removed, follow Step 1.a through Step 1.c in order to install
ring gear (5) to flywheel (1).
a. Identify the orientation of teeth (6) on new ring gear (5).
Note: The chamfered side of ring gear teeth (6) must face toward the starting motor
when the flywheel is installed. The chamfered side of ring gear teeth ensures the
correct engagement of the starting motor.
b. Heat flywheel ring gear (5) in an oven to a maximum temperature of 250 °C (482 °F)
prior to installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (5) is correct and quickly install the ring gear
onto flywheel (1).
2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the
correct procedure.
2/4(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 2 g01336668
Typical example
3. Install a suitable lifting device onto flywheel (1). The flywheel can weigh 71 kg (156 lb).
4. Install Tooling (A) in Position (X) on the crankshaft.
5. Use the lifting device to position flywheel (1) onto Tooling (A).
6. If necessary, install pilot bearing (3) and bolts (2) to flywheel (1).
7. Install bolts (4) to flywheel (1).
8. Remove Tooling (A) and install remaining bolts (4) to flywheel (1).
9. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) and (4) to a
torque of 140 N·m (103 lb ft).
10. Remove the lifting device from flywheel (1).
11. Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further
information.
End By:
a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install" for the correct procedure.
3/4(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR WBF
Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780405
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4389 E10 Torx Socket 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Dispose of all fluids according to local regulations and mandates.
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. The
assembly is not serviceable. If the crankshaft rear seal is removed, the assembly must be replaced.
Illustration 1 g02711971
1. Use Tooling (A) in order to remove torx screws (1) from crankshaft rear seal (2).
2. Remove crankshaft rear seal (2) from the cylinder block. Discard the crankshaft rear seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:15:29 UTC+0800 2020
2/2(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR WBF
Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780403
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4389 E10 Torx Socket 1
B FT-2806 Alignment Tool 1
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 2 g02717045
1. Ensure that crankshaft flange (1) is clean, dry, and free from damage.
2. Ensure that the face of the cylinder block and the bridge piece are clean and dry.
3. A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic
sleeve is squarely installed within crankshaft rear seal (2).
Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is
pushed over the crankshaft flange.
Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The
crankshaft rear seal must be installed dry.
4. Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged
onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft
flange.
During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard
the plastic sleeve.
5. Ensure that crankshaft rear seal (2) is seated against the cylinder block.
3/4(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Illustration 3 g02717046
6. Install torx screws (4) finger tight.
Note: Do not install torx screws to Positions (X) at this stage.
7. Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1). Use Tooling (B)
to align crankshaft rear seal (2) with crankshaft flange (1).
8. Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N·m (195 lb in).
Tighten torx screws (4) in the sequence that is shown in Illustration 3.
9. Remove Tooling (B).
10. Install remaining torx screws (4) to Positions (X). Use Tooling (A) in order to tighten the
torx screws to a torque of 22 N·m (195 lb in). Refer to Illustration 3.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:16:25 UTC+0800 2020
4/4(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR WBF
Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780445
Flywheel Housing - Remove and Install - Standard Housing
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M10 by 100 mm
2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove" for the
correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/7(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 1 g02227473
Typical example
2/7(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Illustration 2 g02227474
Typical example
1. Remove bolts (3) from Position (X) from flywheel housing (1).
2. Install Tooling (A) into Position (X) on flywheel housing (1).
3. Install a suitable lifting device onto the flywheel housing in order to support the flywheel
housing. The weight of the flywheel housing is approximately 40 kg (88 lb).
4. Remove bolts (2) and remaining bolts (3) from flywheel housing (1).
5. Use a suitable lifting device in order to remove flywheel housing (1) from the cylinder
block.
3/7(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. Illustration 3 g01983533
Typical example
6. Remove dust seal (5).
7. If necessary, remove dowels (4) from the cylinder block.
Installation Procedure (Standard Housing)
Table 2
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M10 by 100 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
4/7(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the
flywheel housing.
Illustration 4 g01983535
Typical example
2. Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer
to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure.
3. Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder
block.
4. Install Tooling (A) to the cylinder block.
5. Install dust seal (5).
5/7(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 5 g02227475
Typical example
6. Install a suitable lifting device onto the flywheel housing. The weight of the flywheel
housing is approximately 40 kg (88 lb).
7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel
housing to the cylinder block.
8. Install bolts (2) and bolts (3).
9. Remove Tooling (A). Install remaining bolts (3).
6/7(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Illustration 6 g01984554
Identification of the bolt Grade.
10. When 8.8 Graded bolts are installed, follow Step 10.a through Step 10.b.
a. Tighten bolts (3) to a torque of 63 N·m (46 lb ft).
b. Tighten bolts (2) to a torque of 78 N·m (58 lb ft).
11. When 10.9 Graded bolts are installed follow Step 11.a through Step 11.b.
a. Tighten bolts (3) to a torque of 115 N·m (85 lb ft).
b. Tighten bolts (2) to a torque of 190 N·m (140 lb ft).
12. Check the alignment of flywheel housing (1) with the crankshaft. Refer to System
Operation, Testing and Adjusting, "Flywheel Housing - Inspect" for more information.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 9 23:17:21 UTC+0800 2020
7/7(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR WBF
Configuration: 320D2 & 320D2 L Excavators WBF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i05909468
Vibration Damper and Pulley - Remove
SMCS - 1205-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
Start By:
A. Remove the alternator belt. Refer to Disassembly and Assembly, "V- Belts - Remove and
Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the
crankshaft adapter is approximately 22 kg (48 lb).
1/3(W)
w
2020/1/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...