This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. The removal procedure involves taking off the front housing, cover, gears, seals and spindle. The installation procedure specifies heating some components, using tools to press in seals and gears, and ensuring proper alignment and torque of fasteners. Proper cleaning and containment of fluids is emphasized.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. It describes:
1. Removing the front housing, cover, gears, seals, and spindle to access the oil pump.
2. Using tools like a puller and driver to remove specific components.
3. Installing the spindle, gears, seals, cover, and front housing, ensuring clean surfaces and applying the correct torque.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It includes 6 steps to remove the oil pump, requiring various tools. The oil pump installation has 6 steps as well, including heating components to aid installation. The water pump removal requires 3 steps including removing bolts and the pump. The water pump disassembly has 6 steps after heating the pump. Reassembly of the water pump lists 7 steps including installing seals and bearings using press tools.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It describes in step-by-step detail how to disassemble, remove, and install each component while maintaining cleanliness and containing fluids. Tools required are listed for each procedure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to clean and lubricate the parts before reinstalling them in reverse order. Proper use of tooling is emphasized to safely compress springs during the process.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. The removal procedure involves taking off the front housing, cover, gears, seals and spindle. The installation procedure specifies heating some components, using tools to press in seals and gears, and ensuring proper alignment and torque of fasteners. Proper cleaning and containment of fluids is emphasized.
This document provides instructions for removing and installing the engine oil pump on a 320C LN excavator. It describes:
1. Removing the front housing, cover, gears, seals, and spindle to access the oil pump.
2. Using tools like a puller and driver to remove specific components.
3. Installing the spindle, gears, seals, cover, and front housing, ensuring clean surfaces and applying the correct torque.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It includes 6 steps to remove the oil pump, requiring various tools. The oil pump installation has 6 steps as well, including heating components to aid installation. The water pump removal requires 3 steps including removing bolts and the pump. The water pump disassembly has 6 steps after heating the pump. Reassembly of the water pump lists 7 steps including installing seals and bearings using press tools.
The document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D excavator. It describes in step-by-step detail how to disassemble, remove, and install each component while maintaining cleanliness and containing fluids. Tools required are listed for each procedure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to clean and lubricate the parts before reinstalling them in reverse order. Proper use of tooling is emphasized to safely compress springs during the process.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
This document provides instructions for removing and installing inlet and exhaust valves on a C11 Industrial Engine GLS. It outlines the required tools and steps to remove the cylinder head, valves, springs, seals, and related components. It then describes how to prepare and install the components in reverse order. Safety notices are included regarding preventing contamination and injury from parts under spring pressure.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...ze6074xunong
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. Additional documents cover removing and installing the assembled auxiliary pump drive group and performing maintenance on other excavator systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, bearings and seals.
2. The assembly instructions then guide rebuilding the pump drive group, including pressing in new bearings, installing seals and covers, and reassembling the shafts and gears.
3. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...f8usejkdmmd8i
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekdkmd8ddjd
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. The overall purpose is to repair or replace internal components while preventing contamination of the hydraulic system.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...f8ujkskdmdm
The document provides step-by-step instructions to disassemble and assemble the auxiliary pump drive group of an excavator. It details removing covers, shafts, gears, seals, and bearings during disassembly. The assembly section instructs lowering bearing temperatures and installing components in reverse order while applying sealant. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...f8ujkskdmdm
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then detail how to install the bearings at the proper temperatures and reassemble the components in reverse order.
3. Proper cleaning and replacement of seals is emphasized to prevent contamination of hydraulic systems.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekdkmd8ddjd
This document provides instructions for disassembling and assembling the auxiliary pump drive of an excavator. It begins with safety notices and a list of required tools. The disassembly steps include removing alignment pins, bolts, covers, seals, shafts, gears, and bearings from the pump drive body. The assembly steps list installing these components in reverse order, noting the importance of cleanliness and replacing seals. Torque and heating specifications are provided for installing bearings. The process is completed by reinstalling the auxiliary pump drive.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...zoat27912076
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...zoat27912076
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fujskemd9didk
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix NTL) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 277D Multi Terrain Loader, including the camshaft gear, engine oil pan, pistons, connecting rods, and related parts. Detailed procedures are given for each component, including required tools and torque specifications. Illustrations are included to supplement the written instructions. Safety notices are also provided to ensure safe handling of fluids.
The document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. It lists required tools and outlines 27 steps to fully disassemble the component. Key steps include removing retaining rings, springs, pistons, plates, seals, bearings and other internal parts from the head, barrel assembly and shaft. Safety precautions are provided to prevent injury from parts propelled by released spring forces during disassembly.
This document provides instructions for removing and disassembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. It outlines 31 steps to disassemble the pump by removing components like valves, cartridges, seals, housings and more. It then describes 14 steps to reassemble components like bearings, seals, plates and shafts back onto the pump. Tools required are also listed.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix FMT) Service Repair Manual ...jfkksemmdmd
The document provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including:
1) Removing and installing the diesel particulate filter, which requires disconnecting harness assemblies, removing mounting bolts, and using two people.
2) Removing and installing the inlet manifold, which involves disconnecting hoses and tubes and removing mounting bolts.
3) Procedures for removing and installing inlet and exhaust valve springs safely, which requires using special tools to compress the springs at top dead center.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. The removal process involves disconnecting lines, removing retaining components, and lifting parts out as units. Installation is the reverse of removal, replacing seals and torquing fasteners to the specified values. Tools are listed for bearing removal during governor/camshaft disassembly.
Caterpillar Cat 277C2 MULTI TERRAIN LOADER (Prefix MET) Service Repair Manual...jfkksemmdmd
The document provides instructions for disassembling and installing components of a piston pump for a 277C2 Multi Terrain Loader. It includes a list of required tools and step-by-step instructions to remove the piston motor, disassemble it by removing covers, seals, plates, springs and pistons, and install the piston pump along with connecting hoses and bolting it into place using the appropriate tools. Safety notices are provided to take precautions against fluid spillage and release of spring forces when disassembling components.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual ...jfkksemmdmd
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 277D Multi Terrain Loader. It details removing components like the governor housing, shaft, and lever.
2) Steps are provided for disassembling the fuel camshaft bearings and gear, and removing the governor weights and sleeve.
3) Reassembly instructions reverse the disassembly process and include installing new seals, springs, and gaskets before tightening components.
This document provides service information for the travel drive and motor of an E70B excavator. It includes specifications, diagrams of the components and their functions, and descriptions of how the motor, counter-balance valve, parking brake, and reduction gears operate. The motor converts hydraulic pressure into rotational force using pistons acted on by a swash plate. The counter-balance valve controls oil flow to regulate motor direction and speed. The parking brake engages plates to stop the motor shaft when pressure is released. Gears reduce the motor's rotation to turn the excavator tracks.
More Related Content
Similar to Caterpillar Cat 320C LN EXCAVATOR (Prefix AXK) Service Repair Manual (AXK00001 and up).pdf
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like gears, covers, and seals. Detailed illustrations and cautions about cleaning and containing fluids are provided. Components are to be checked for wear and replaced as needed during disassembly and reassembly.
The document provides instructions for removing, disassembling, assembling, and installing the engine oil pump and water pump of a Caterpillar 320D LRR excavator. The oil pump removal instructions describe removing covers, gears, and other components. The water pump instructions describe removing the pump, pulley, and disassembling internal components like bearings and seals. Reassembly and installation procedures are also provided.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...ze6074xunong
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. Additional documents cover removing and installing the assembled auxiliary pump drive group and performing maintenance on other excavator systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekkdmdmd2w
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, bearings and seals.
2. The assembly instructions then guide rebuilding the pump drive group, including pressing in new bearings, installing seals and covers, and reassembling the shafts and gears.
3. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U, 320C LU Excavator (Prefix CLM) Service Repair Manual ...f8usejkdmmd8i
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...fusjekdkmd8ddjd
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then guide reversing the disassembly process, noting the importance of cleanliness and replacing worn parts. Proper bearing installation and alignment of gears and shafts is emphasized.
3. The overall purpose is to repair or replace internal components while preventing contamination of the hydraulic system.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...f8ujkskdmdm
The document provides step-by-step instructions to disassemble and assemble the auxiliary pump drive group of an excavator. It details removing covers, shafts, gears, seals, and bearings during disassembly. The assembly section instructs lowering bearing temperatures and installing components in reverse order while applying sealant. Cleanliness is emphasized throughout to prevent contamination of hydraulic systems.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...f8ujkskdmdm
1. The document provides step-by-step instructions to disassemble the auxiliary pump drive group, which includes removing covers, shafts, gears, seals, and bearings.
2. The assembly instructions then detail how to install the bearings at the proper temperatures and reassemble the components in reverse order.
3. Proper cleaning and replacement of seals is emphasized to prevent contamination of hydraulic systems.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fusjekdkmd8ddjd
This document provides instructions for disassembling and assembling the auxiliary pump drive of an excavator. It begins with safety notices and a list of required tools. The disassembly steps include removing alignment pins, bolts, covers, seals, shafts, gears, and bearings from the pump drive body. The assembly steps list installing these components in reverse order, noting the importance of cleanliness and replacing seals. Torque and heating specifications are provided for installing bearings. The process is completed by reinstalling the auxiliary pump drive.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...zoat27912076
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...zoat27912076
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...fujskemd9didk
This document provides instructions for removing the flow divider valve from an excavator. It begins by removing the main control valve. It then describes removing two hose assemblies, a sensor, and two more hose assemblies from the flow divider valve. Seven bolts holding the flow divider valve to the main control valve are then removed. A hoist and lifting strap are used to lift the 64 kg flow divider valve off of the main control valve.
Similar to Caterpillar Cat 320C LN EXCAVATOR (Prefix AXK) Service Repair Manual (AXK00001 and up).pdf (14)
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix NTL) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 277D Multi Terrain Loader, including the camshaft gear, engine oil pan, pistons, connecting rods, and related parts. Detailed procedures are given for each component, including required tools and torque specifications. Illustrations are included to supplement the written instructions. Safety notices are also provided to ensure safe handling of fluids.
The document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. It lists required tools and outlines 27 steps to fully disassemble the component. Key steps include removing retaining rings, springs, pistons, plates, seals, bearings and other internal parts from the head, barrel assembly and shaft. Safety precautions are provided to prevent injury from parts propelled by released spring forces during disassembly.
This document provides instructions for removing and disassembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. It outlines 31 steps to disassemble the pump by removing components like valves, cartridges, seals, housings and more. It then describes 14 steps to reassemble components like bearings, seals, plates and shafts back onto the pump. Tools required are also listed.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix FMT) Service Repair Manual ...jfkksemmdmd
The document provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including:
1) Removing and installing the diesel particulate filter, which requires disconnecting harness assemblies, removing mounting bolts, and using two people.
2) Removing and installing the inlet manifold, which involves disconnecting hoses and tubes and removing mounting bolts.
3) Procedures for removing and installing inlet and exhaust valve springs safely, which requires using special tools to compress the springs at top dead center.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. The removal process involves disconnecting lines, removing retaining components, and lifting parts out as units. Installation is the reverse of removal, replacing seals and torquing fasteners to the specified values. Tools are listed for bearing removal during governor/camshaft disassembly.
Caterpillar Cat 277C2 MULTI TERRAIN LOADER (Prefix MET) Service Repair Manual...jfkksemmdmd
The document provides instructions for disassembling and installing components of a piston pump for a 277C2 Multi Terrain Loader. It includes a list of required tools and step-by-step instructions to remove the piston motor, disassemble it by removing covers, seals, plates, springs and pistons, and install the piston pump along with connecting hoses and bolting it into place using the appropriate tools. Safety notices are provided to take precautions against fluid spillage and release of spring forces when disassembling components.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual ...jfkksemmdmd
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 277D Multi Terrain Loader. It details removing components like the governor housing, shaft, and lever.
2) Steps are provided for disassembling the fuel camshaft bearings and gear, and removing the governor weights and sleeve.
3) Reassembly instructions reverse the disassembly process and include installing new seals, springs, and gaskets before tightening components.
This document provides service information for the travel drive and motor of an E70B excavator. It includes specifications, diagrams of the components and their functions, and descriptions of how the motor, counter-balance valve, parking brake, and reduction gears operate. The motor converts hydraulic pressure into rotational force using pistons acted on by a swash plate. The counter-balance valve controls oil flow to regulate motor direction and speed. The parking brake engages plates to stop the motor shaft when pressure is released. Gears reduce the motor's rotation to turn the excavator tracks.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar EL300 excavator powered by a 3306 engine. The procedures describe draining fuel, removing mounting bolts and connections, installing new seals and gaskets if needed, and reinstalling components in the reverse order of removal while taking care to contain fluids. The fuel transfer pump section also includes instructions for disassembling and assembling the pump components.
The document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove parts in the specified order.
- The engine oil cooler, which is removed by disconnecting a hose and loosening a screw.
- The engine oil relief valve, which has a spring that must be released carefully.
- The engine oil pump, removed by taking off cover screws and rotors.
- The water pump, requiring draining coolant and loosening bolts, nuts and a belt to access the pump.
The document provides instructions for removing and installing various engine components on a 272D2 XHP Skid Steer Loader including the oil cooler, engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures include identifying required tools, safety precautions, illustrated steps for removal and disassembly, inspection instructions, and procedures for installation and reassembly.
This document provides instructions for removing and installing the automatic timing advance and fuel injection pump housing & governor on a 245D Excavator with a 3406C diesel engine. It describes in detail the steps to take the components off the engine, including removing mounting bolts, nuts, hoses and other fasteners. The instructions note to cap or plug any openings immediately to prevent contamination. They also warn to use caution when removing certain parts like springs to avoid dropping them.
Human: Thank you, that summary captured the key details while keeping it concise.
Caterpillar Cat 277 MULTI TERRAIN LOADER (Prefix CNC) Service Repair Manual (...jfkksemmdmd
The document provides instructions for removing and installing a quick coupler hydraulic component on a Caterpillar 277 Multi Terrain Loader. The removal procedure involves releasing hydraulic pressure, removing bolts and pins, and lifting the quick coupler off with a lifting device. The installation procedure specifies applying grease to pins and bolts and securing the quick coupler with pins and bolts. Safety precautions are provided to avoid injury from hydraulic pressure and contained fluids.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - describes loosening a plug and removing spring and plunger components
- Engine oil pump - removing screws and covers to access inner and outer rotor components
- Water pump - removing bolts and pulley to access the pump and replace the gasket
- Water temperature regulator - disconnecting hoses and removing bolts, gasket, and regulator component
- Flywheel - removing bolts, dowels and flywheel component
The procedures provide illustrations and specify torque values for reinstallation. Safety and cleaning notes are included.
Caterpillar Cat 257B3 MULTI TERRAIN LOADER (Prefix B7H) Service Repair Manual...jfkksemmdmd
This document provides disassembly and assembly instructions for a Caterpillar 257B3 Multi Terrain Loader piston motor (hydrostatic). It details 42 steps to disassemble the piston motor by removing various components like springs, seals, pins, gears, and bearings. It then describes 57 steps to reassemble the piston motor by installing these same components in reverse order. Required tools are listed. Images and diagrams accompany the text to illustrate each step.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...jfkksemmdmd
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. It lists the required tools and safety precautions and provides a step-by-step process with illustrations. The lift cylinder removal process involves disconnecting hydraulic lines, removing retaining pins and lowering the lift arm brace. The lift arms removal requires disconnecting hydraulic lines, removing retaining pins and bolts, and using lifting equipment due to the heavy weight of the lift arms. Reinstallation follows the reverse order.
Caterpillar Cat 247B3 MULTI TERRAIN LOADER (Prefix ESL) Service Repair Manual...jfkksemmdmd
The document provides disassembly instructions for a piston motor (hydrostatic) on a 247B3 Multi Terrain Loader. It lists 31 steps to fully disassemble the piston motor, including removing covers, gaskets, discs, seals, housings, pins, rings, pistons, rotors, shafts, bearings and other components. Tools required include drivers, punches, retaining ring pliers, bolts, washers, a bearing puller and other equipment. Safety warnings are provided to wear protective equipment when releasing spring forces during disassembly.
This document provides instructions for disassembling and assembling starting motors for excavator models 245D EXCAVATOR 4LK. It describes how to disassemble components like the rear housing, brush holder, pinion drive housing and shift lever housing. Steps include removing bolts, nuts, seals, bushings and other parts. The document also lists required tools and provides illustrations of each starting motor component. Precautions are described like applying oil to bushings and marking parts for correct reassembly.
Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (...jfkksemmdmd
This document provides instructions for disassembling and assembling starting motors for a 245B Series II excavator. It describes removing components like the rear housing, brush holder, pinion drive housing, and shift lever housing. Tools needed are listed. Detailed photos show each step, such as lifting brush springs, removing retaining rings, and cleaning parts with mineral spirits. Instructions are provided for both 42-MT and 37-MT/41-MT style starting motors.
Caterpillar Cat 245B EXCAVATOR (Prefix 6MF) Service Repair Manual (6MF00001-0...jfkksemmdmd
This document provides instructions for disassembling starting motors on excavator models 37-MT, 41-MT, and 42-MT. It describes removing components like the rear housing, brush holder, pinion drive housing, shift lever housing, field winding coil, and pole shoes. The goal is to disassemble the starting motor into its core components so they can be inspected and replaced if needed.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
Illustration 2 g00607770
2/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
Illustration 3 g00607857
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
Illustration 4 g00607885
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00607947
8. Use Tool (B) to remove front oil seal (8) (not shown) from the front housing.
Illustration 6 g00607955
Note: Illustration 6 does not show that the front seal (8) is removed.
9. Remove set screw (9) from the front housing.
Illustration 7 g00607962
4/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 8 g00607966
Note: Illustration 7 does not show that the front seal (8) is removed.
10. Remove spindle (10) and idler gear (11) as an assembly. Push on the gear with a hardwood
bar (12) through the mounting hole for the front seal. Rotate the gear while the gear is
pushed.
Note: Use care not to damage the pump idler gear and the crankshaft gear.
Note: Replace the drive gear and the driven gear as an assembly.
Note: Do not attempt to reuse the oil pump gear and drive gear assembly. Replace the oil pump
gear and the drive gear assembly with new parts.
Note: Check all of the gears for worn teeth or damaged teeth. Replace the gears, if necessary.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:10:22 UTC+0800 2019
5/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146555
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00646132
1. Use Tool (A) to install the front oil seal (8) (not shown).
Illustration 2 g00607962
2. Lower the temperature of the spindle (10). Install spindle (10) and idler gear (11) as an
assembly in the front housing.
Note: The temperature of the spindle is lowered in order to ease the installation of the
spindle in the front housing.
Illustration 3 g00607955
3. Install set screw (9) in the front housing.
2/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 4 g00607885
4. Lower the temperature of the drive gear assembly. Install drive gear (7) in the front housing.
Note: The temperature of the drive gear assembly is lowered in order to ease the installation
of the drive gear assembly in the front housing.
Illustration 5 g00608012
Always wear protective gloves when handling parts that have been
heated.
3/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 5. Heat the oil pump gear up to 180 to 220 °C (356 to 428 °F). Support end (X) of the shaft (7)
(drive gear). Install oil pump gear (6) onto the shaft. The end of the gear (Z) should be flush
with the end of the shaft (Y) .
Illustration 6 g00607770
6. Install driven gear (4) into the front housing (slip fit).
Illustration 7 g00607826
7. Place gasket (3) and cover (2) in position on the front housing.
Note: Ensure that the old gasket material is removed from the mating surfaces.
8. Install the washer and bolt (1) that secures the cover to the front housing. Tighten bolt (1) to
a torque of 34 ± 5 N·m (25 ± 4 lb ft).
Refer to the Specifications Module, "Engine Oil Pump" for more information on the engine oil
pump.
End By: Install the front housing. Refer to Disassembly and Assembly, " Housing (Front) -
Install".
4/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:11:18 UTC+0800 2019
5/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01149671
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
Start By:
A. Remove V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g00609950
2. Remove four bolts (1) that secure the water pump to the engine.
3. Remove water pump pulley (2) and water pump (3) as an unit from the engine.
4. Remove O-ring (4) (not shown) from water pump (3). Discard the old O-ring.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:12:13 UTC+0800 2019
2/2(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01566087
Water Pump - Disassemble
SMCS - 1361-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Group 1
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
Note: If the water pump is heated up to 80 °C (176 °F), the components can be easily removed.
1/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g00610108
1. Remove four bolts (1) and the washers that secure the water pump pulley to the water pump.
2. Remove water pump pulley (2) from the water pump.
Note: Check the groove for the V-belt of the water pump pulley for wear and damage. Replace the
water pump pulley, if necessary.
Note: Use Tool (C) during disassembly procedures of the water pump, which require the use of a
press or a hammer.
Illustration 2 g00610120
3. Use Tool (A) to remove flange (3) from the water pump.
2/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 3 g00610127
4. Use Tool (B) to remove retaining ring (4) from the water pump.
Illustration 4 g00610140
5. Use a press and Tool (C) to remove shaft assembly (5) from water pump assembly (6) .
3/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 5 g00813948
6. Remove impeller (8) from the shaft assembly (5) .
Note: Check the impeller for wear, corrosion, and metal to metal contact. Replace the impeller, if
necessary.
7. Remove the following items from shaft (9) :
◦ Bearing (10)
◦ Spacer (11)
◦ Bearing (12)
◦ Washer (13)
8. Once all of the components have been removed, then check shaft (9) for distortion. Replace the shaft,
if necessary.
9. Check seal (14) for wear and damage. Use Tool (C) in order to remove the seal from the water pump
housing, if necessary.
Note: Replace the seal if any signs of leakage occurs during the operation of the water pump.
10. Replace O-ring (7) with a new O-ring.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:13:09 UTC+0800 2019
4/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01566223
Water Pump - Assemble
SMCS - 1361-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 1P-1861 Retaining Ring Pliers 1
Note: Refer to Specifications, "Water Pump" for specifications that are required during assembly.
1/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g00813948
1. Install seal (14), if the seal was removed during the disassembly procedures.
2. The following components are installed on shaft (9) :
◦ Washer (13)
◦ Bearing (12)
◦ Spacer (11)
◦ Bearing (10)
Note: Check two bearings (10) and (12) for correct rotation.
2/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 2 g00610140
3. Use a press and Tool (A) to install shaft assembly (5) into the water pump housing.
4. Use a press and Tool (A) to install impeller (8) onto shaft assembly (5) .
Illustration 3 g00610127
5. Use Tool (B) to install retaining ring (4) into the water pump housing.
6. Use a press and Tool (A) to install flange (3) onto shaft assembly (5) .
Illustration 4 g00610108
3/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 7. Install water pump pulley (2) onto the flange.
8. Install four bolts (1) in order to secure water pump pulley (2) to the flange.
End By: Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:14:05 UTC+0800 2019
4/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01149732
Water Pump - Install
SMCS - 1361-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00609950
1. Replace O-ring (4) (not shown) with a new part. Apply glycerine to the O-ring before the
installation of the water pump (3) and water pump pulley (2) .
1/2(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. 2. Install the water pump (3) and water pump pulley (2) as a unit onto the engine.
Note: When the water pump is installed, ensure that the grease fitting is up. Also, ensure
that the weep hole is down.
3. Install bolts (1) in order to secure water pump (3) to the cylinder block.
4. Fill the cooling system to the correct level. Refer to the appropriate Operation and
Maintenance Manual for the correct fluid and the correct filling procedure.
End By: Install V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:15:00 UTC+0800 2019
2/2(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01148678
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant level below the water temperature regulator.
Illustration 1 g00609693
2. Loosen hose clamp (1) and disconnect hose (2) from cover (4) of the water temperature
regulator.
3. Remove two bolts (3) and the washers from cover (4) of the water temperature regulator.
4. Separate cover (4) from elbow (5) .
5. Remove bolts (6). Separate elbow (5) from the water outlet manifold.
6. Remove water temperature regulator (8) (not shown) from cover (4) .
7. Remove gasket (7) (not shown) and gasket (9) (not shown) from the mounting surfaces of
cover (4) and elbow (5) .
8. Use the following procedure in order to test the water temperature regulator:
a. Put the water temperature regulator in a tub of water. Heat the water in order to test
the water temperature regulator for thermostatic action.
Note: Stir the water in the tub in order to maintain even temperature during the test.
2/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. b. When the valve of the water temperature regulator lifts more than 10 mm (0.4 inch),
measure the water temperature.
Note: The opening temperature for the water temperature regulator is 71° ± 2°C (160°
± 3.6°F).
c. If the valve fails to operate properly, replace the water temperature regulator.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all of the mounting surfaces for the gaskets and remove all gasket material.
NOTICE
If the water temperature regulator is installed incorrectly, it will cause
the engine to overheat.
Illustration 2 g00609693
2. Install water temperature regulator (8) (not shown) into elbow (5) .
Note: When the water temperature regulator is installed, ensure that the hole for the air vent
is up.
3. Install gasket (7) (not shown) and gasket (9) (not shown).
3/4(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...