Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
2. S/N - TMF1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
S/N - XBB1-UP
S/N - XCC1-UP
S/N - YEA1-UP
S/N - ZBD1-UP
S/N - ZCS1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1859 Retaining Ring Pliers 1
E 1P-0510 Driver Group 1
F 1U-6396 O-Ring Assembly Compound
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring seal. Use Tooling (F) during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
2/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00705445
1. Install O-ring seal (45) onto the fitting (44).
Illustration 2 g00705442
2. Install fitting (44) into the motor housing.
Illustration 3 g00705441
3. Lubricate the lip seal (43) with clean hydraulic oil. install lip seal (43) into the motor
housing with the lip toward the inside of the motor housing.
3/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 4 g01022013
Typical Example
Illustration 5 g01287176
4. Use Tooling (E) to install bearing (42) into the motor housing.
Illustration 6 g00705595
5. Raise the temperature of bearing race (41). Install the bearing race on the shaft.
4/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 7 g00705592
6. Raise the temperature of bearing race (40). Install the bearing race on the shaft.
Illustration 8 g00705597
Illustration 9 g00705258
7. Install shrink wrap tubing onto shaft (39). The shrink wrap tubing will protect the seal
during installation of shaft (39). Install shaft (39) into the motor housing.
5/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 10 g00705602
8. Use Tooling (B) to install retaining ring (38) onto shaft (39). Remove the shrink wrap
tubing.
Illustration 11 g00705209
9. Install swashplate (37) into the motor housing.
Illustration 12 g01021919
Typical Example
10. Install O-ring seals (36) and (36a) into the motor housing.
6/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 13 g01021909
11. Connect plates (34) and (35).
Illustration 14 g01021903
12. Install pistons (33) into plates (34) and (35).
Illustration 15 g01021898
13. Install pistons (33) into barrel (32).
7/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 16 g01022034
14. Install barrel (32) and the piston assembly into the motor housing as one unit. It may be
necessary to use string to keep the barrel and the piston assembly together during
installation.
Illustration 17 g01022038
Note: Make sure that the tooth cut locations of each friction plate are in alignment. Also, the
tooth cut locations of each separator plate must be in alignment in the body of the swing
motor.
15. Apply clean hydraulic oil on four separator plates and three friction plates (31). Install
plates (31) in alternating order in the body of the swing motor. Begin with a separator plate,
and end with a separator plate.
8/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 18 g01021875
16. Install piston (30) into the motor housing.
Illustration 19 g00704796
17. Install port plate (29) into the motor housing. Install springs (28) into the motor housing.
Illustration 20 g00704771
18. Install spring pins (26) and bearing (27) into the head.
Illustration 21 g00704754
9/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 19. Install O-ring seal (25) onto the head.
Illustration 22 g00704749
20. Install O-ring seal (23) and O-ring seal (24) onto the fittings (19) and (20).
Illustration 23 g00704743
21. Install O-ring seal (22) onto the plug (21).
Illustration 24 g00704741
22. Install tee fitting (19), fitting (20), and plugs (21) into the head. Tighten plugs (21) to a
torque of 59 ± 6 N·m (44 ± 4 lb ft).
10/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 25 g00704734
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
23. Install spool valve (15), spring (16), O-ring seal (17), and plug (18) into the head. Tighten
plug (18) to a torque of 334 ± 33 N·m (246 ± 24 lb ft). Repeat for the opposite side.
Illustration 26 g00705818
24. Install port plate (29) onto the head.
11/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 27 g00705827
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
25. Install springs (28) onto the piston. Install head (1) onto the motor housing.
Illustration 28 g00704719
26. Install bolts (14) into the head. Tighten bolts (14) to a torque of 430 ± 43 N·m
(317 ± 32 lb ft).
12/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 29 g00704710
27. Install O-ring seals (10), (12), and (13). Install back up rings (9) and (11).
Illustration 30 g00704704
28. Install relief valves (8) into the head.
Illustration 31 g00704621
13/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 29. Install dipstick tube (5) and breather tube (6) into motor housing (7).
Illustration 32 g00704611
30. Install mounting bolts (4). Install anti-reaction valve (3) into head (1). Install bolts (2).
End By:
a. Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 11 14:30:58 UTC+0800 2020
14/14(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. S/N - TMF1-UP
S/N - WDJ1-UP
S/N - XAN1-UP
S/N - XBB1-UP
S/N - XCC1-UP
S/N - YEA1-UP
S/N - ZBD1-UP
S/N - ZCS1-UP
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
C 1U-8846 Gasket Sealant
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Prior to the installation of the swing motor, make sure that the mating surfaces of the swing
motor and the swing drive are thoroughly clean and dry.
2. Apply Tooling (C) on the mating surface of the swing motor and the swing drive housing.
2/7(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g00694494
3. Attach Tooling (B) and a suitable lifting device to swing motor (23). The weight of swing
motor (23) is approximately 55 kg (120 lb).
Illustration 2 g00694484
4. Install the washers and bolts (20).
5. Tighten bolts (20) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
6. Install anti-reaction valve (22). Install the washers and bolts (21). Tighten bolts (21) to a
torque of 55 ± 10 N·m (40 ± 7 lb ft).
Illustration 3 g00690963
3/7(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 7. Remove the cap to the hydraulic tank. Attach Tooling (A) to the hydraulic tank.
Note: Hook up the air to Tooling (A) in order to create a vacuum in the hydraulic system.
This will minimize the leakage from the hose assemblies.
Note: Replace the O-ring seals that are used in the ends of the hose assemblies.
Illustration 4 g00695023
8. Connect hose assembly (19).
Illustration 5 g00694470
9. Connect hose assembly (13).
10. Install the split flanges, the washers and bolts (15).
11. Connect hose assembly (16).
12. Connect hose assembly (11).
13. Install the split flanges, the washers, and bolts (14).
14. Connect hose assembly (12).
15. Connect hose assembly (10).
4/7(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 16. Connect harness assembly (18).
17. Install the clip, the washer, and bolt (17).
Illustration 6 g00694459
Typical example
18. Connect hose assembly (7) (If Equipped).
19. Install hose assembly (6) (If Equipped).
20. Install brace (8) with washers and bolts (9) (If Equipped).
Illustration 7 g00694353
21. Make sure that the drain valve (5) is closed.
22. Remove Tooling (A) and install the cap to the hydraulic tank.
NOTICE
To avoid system damage, make sure that the hydraulic motor is
properly filled with hydraulic oil before start-up.
5/7(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 23. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
24. Fill the hydraulic oil tank and the swing drive with clean hydraulic oil to the correct level.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level -
Check" and Operation and Maintenance Manual, "Swing Drive Oil Level - Check" for the
correct filling procedures.
25. Start the engine, and check the operation of the swing drive. Also, check for leaks. Stop the
engine.
26. Obtain a hydraulic oil sample from the main S·O·S port.
Reference: Refer to Operation and Maintenance Manual, "Sampling Interval and Location
of Sampling Valve" for the correct location.
27. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
Reference: Refer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 320C Hydraulic Excavators" for further information.
Illustration 8 g00694245
28. Install the washers and bolts (4) in order to install access cover (3) that is under the main
control valve.
6/7(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 9 g00950370
29. Install the washers and bolts (1) in order to install cover (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 11 14:31:54 UTC+0800 2020
7/7(W)w
2020/1/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...