What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR HKT
Configuration: 320C & 320C L Excavators HKT00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01525672
Control Valve (Auxiliary) - Install - F1 and F4 Auxiliary
Control Valves
SMCS - 5051-012-AX
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) FT-2674 Vacuum Cap 1
(B) 138-7573 Link Bracket 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Install two hose assemblies on the bottom of the (F4) auxiliary control valve.
1/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00704077
2. Fasten F1 and F4 auxiliary control valves together with the existing mount bolts. Fasten the
control valves at the top with a washer and nut (28), as shown.
3. Install the F1 and F4 auxiliary control valves.
4. Lower the F1 and F4 auxiliary control valves in order to connect the hoses and electrical
connections on the bottom of the auxiliary control valves.
Illustration 2 g00690963
5. Remove the cap to the hydraulic tank. Attach Tooling (A) to the hydraulic tank.
Note: Hook up the air to Tooling (A) in order to create a vacuum in the hydraulic system.
This will minimize the leakage to the hose assemblies.
2/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00703894
6. Connect two pilot lines (30) to the bottom of each control valve.
Illustration 4 g00703965
7. Connect one electrical connector (29) to each control valve.
Illustration 5 g00703950
8. Align the auxiliary control valves with the main control valve. Install the bottom two mount
bolts (27).
3/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 9. Remove nut (28) and the washer from the top two mount bolts that pass through control
valves (F1) and (F4).
10. Install the top two mount bolts.
11. Tighten the four mount bolts (27) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
12. Connect one electrical connector (26) to each control valve.
Illustration 6 g00703893
13. Remove 7X-2547 Bolt (25).
14. Remove Tooling (B) and the hoist. Install the original bolt (25).
Illustration 7 g00703941
15. Install bolts (23) in order to connect tube (24) to the (F1) control valve.
4/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 8 g00703888
16. Install bolts (21) in order to connect tube (22) to the (F4) control valve.
Illustration 9 g00703729
17. Install bolts (19) in order to connect tube (20) to the (F4) control valve.
18. Connect hose assembly (18) to the (F4) control valve.
5/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 10 g00703717
19. Connect hose assembly (17) to the (F1) control valve.
20. Connect two hose assemblies (16) to both control valves.
Illustration 11 g00703706
21. Connect three hose assemblies (15) to the (F1) control valve.
Illustration 12 g00703705
22. Install panels (14) and support (12).
23. Install the washers and bolts (13) that hold the panels and support together.
6/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 13 g00703703
24. Install air filter (10).
25. Install the washers and bolts (9) in order to hold the air filter and the support to the machine.
Illustration 14 g00703690
Illustration 15 g00703702
26. Install hose (6) and install two hose clamps (7).
7/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 16 g00703704
27. Connect two electrical connectors (11) to the air filter. Install a new tie strap.
Illustration 17 g00792422
28. Close side door (8).
Illustration 18 g00703510
(F1) Auxiliary control valve
(F4) Auxiliary control valve
29. Install five pilot lines (5).
8/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 30. Remove Tooling (A).
31. Install high efficiency filters in place of the pilot filter, case drain filter, and the return filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
32. Fill the hydraulic oil tank and the swing drive with clean hydraulic oil to the correct level.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level -
Check" for the correct filling procedures.
33. Install the cap to the hydraulic tank.
34. Start the engine, and check the operation of the auxiliary attachments. Also, check for leaks.
Stop the engine.
35. Obtain a hydraulic oil sample from the main S·O·S port.
Reference: Refer to Operation and Maintenance Manual, "Sampling Interval and Location
of Sampling Valve" for the correct location.
36. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
Reference: Refer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
Illustration 19 g00703691
37. Install four bolts (4) and the washers in order to hold cover (3).
38. Install four bolts (2) and the washers in order to hold cover (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 13 08:36:29 UTC+0800 2019
9/9(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR HKT
Configuration: 320C & 320C L Excavators HKT00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01539518
Control Valve (Auxiliary) - Install - F2 and F3 Auxiliary
Control Valves
SMCS - 5051-012-AX
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) FT-2674 Vacuum Cap 1
(B) 138-7573 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00721124
1. Fasten (F2) and (F3) auxiliary control valves together with the existing mount bolts. Fasten
the control valves at the top with a washer and nut (30), as shown.
Illustration 2 g00719363
2. Install pilot lines (31), (32), (33), (34), (35), and (36) on the (F2) and (F3) auxiliary control
valves.
2/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 3 g00721171
Top view of the auxiliary control valves
Illustration 4 g00721173
Bottom view of the auxiliary control valves
3. Pilot line (31) runs from the top of the (F2) control valve to the bottom of the (F3) control
valve. Pilot line (32) runs from the top of the (F2) control valve to the bottom of the (F2)
control valve. Pilot line (33) runs from the top of the (F3) control valve to the bottom of the
(F2) control valve. Pilot line (34) runs from the top of the (F3) control valve to the bottom
of the (F3) control valve. Pilot line (35) runs from the top of the (F3) control valve to the
bottom of the (F3) control valve. Pilot line (36) runs from the top of the (F3) control valve
to the bottom of the (F2) control valve.
4. Install the (F2) and (F3) auxiliary control valves.
3/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 5 g00690963
5. Remove the cap to the hydraulic tank. Attach Tooling (A) to the hydraulic tank.
Note: Hook up the air to Tooling (A) in order to create a vacuum in the hydraulic system.
This will minimize the leakage to the hose assemblies.
Illustration 6 g00719336
6. Align the auxiliary control valves with the main control valve. Install the bottom two mount
bolts (29).
Illustration 7 g00719342
4/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. 7. Remove nuts (30) and the washer from the top two mount bolts that pass through control
valves (F2) and (F3).
8. Install the top two mount bolts.
9. Tighten the four mount bolts (29) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
Illustration 8 g00719291
10. Remove 7X-2547 Bolt (28).
11. Remove Tooling (B) and the hoist. Install the original bolt (28).
Illustration 9 g00719289
12. Connect the electrical connector to solenoid (26) and solenoid (27). Solenoid (26) is located
on the bottom side of the (F2) auxiliary control valve. Solenoid (27) is located on the
bottom side of the (F3) auxiliary control valve.
5/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 10 g00719287
13. Connect pilot lines (22) and (25) to the (F2) auxiliary control valve. Connect the electrical
connector to solenoid (23) and solenoid (24).
Illustration 11 g00719260
14. Connect hose assemblies (21) and (20) to the (F2) auxiliary control valve.
Illustration 12 g00719249
15. Connect hose assembly (19) to the (F2) auxiliary control valve.
6/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 13 g00719134
16. Connect hose assembly (18) to the (F2) auxiliary control valve.
Illustration 14 g00719132
17. Connect hose assemblies (17) and (16) to the (F3) auxiliary control valve.
Illustration 15 g00719126
18. Connect hose assembly (15) to the (F3) auxiliary control valve.
7/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 16 g00703705
19. Install support (12) and panels (14). Install bolts (13) and the washers.
20. Install air filter (10).
Illustration 17 g00703704
21. Connect two electrical connectors (11) to the air filter.
8/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 18 g00703703
22. Install washers and bolts (9).
Illustration 19 g00799648
23. Close side door (8).
Illustration 20 g00719373
Illustration 21 g00703690
24. Install hose (6) and tighten two hose clamp (5) and (7).
9/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 22 g00690963
25. Disconnect the air to Tooling (A). Remove Tooling (A) from the hydraulic tank. Install the
cap for the hydraulic tank.
26. Install high efficiency filters in place of the pilot filter, case drain filter, and the return filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
27. Fill the hydraulic oil tank and the swing drive with clean hydraulic oil to the correct level.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level -
Check" for the correct filling procedures.
28. Install the cap to the hydraulic tank.
29. Start the engine, and check the operation of the auxiliary attachments. Also, check for leaks.
Stop the engine.
30. Obtain a hydraulic oil sample from the main S·O·S port.
Reference: Refer to Operation and Maintenance Manual, "Sampling Interval and Location
of Sampling Valve" for the correct location.
31. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
Reference: Refer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
10/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 23 g00703691
32. Install cover (3). Install washers and four bolts (4).
33. Install cover (1). Install washers and four bolts (2).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 13 08:37:29 UTC+0800 2019
11/11(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR HKT
Configuration: 320C & 320C L Excavators HKT00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564828
Fuel Priming Pump - Remove and Install
SMCS - 1258-010
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 1 g00606436
1. Remove banjo bolt (1) and washers (2) (not shown) from the fuel priming pump in order to
remove fuel outlet line (3) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
2. Loosen hose clamp (4) in order to remove fuel supply line (5) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
Illustration 2 g00606441
3. Remove nuts (6) that secure the fuel priming pump to the fuel injection pump.
Note: Fuel will drain from the fuel priming pump during removal. Collect the fuel in a
suitable container for storage or for disposal.
4. Remove fuel priming pump (7) and the O-ring (8) (not shown).
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
Installation Procedure
2/4(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 3 g00606441
Note: Check the O-ring (8) (not shown) for wear or damage. Replace a worn O-ring or a
damaged O-ring with a new replacement part.
1. Place the O-ring (8) (not shown) and place the fuel priming pump (7) in position on the fuel
injection pump.
2. Install nuts (6) that secure the fuel priming pump to the fuel injection pump.
Illustration 4 g00606436
3. Connect fuel supply line (5) and hose clamp (4) to the fuel priming pump.
4. Tighten the hose clamps.
Note: Check the washers (2) (not shown) for wear or damage. Replace a worn washer or a
damaged washer with a new replacement part.
5. Secure the fuel outlet line (3) and the washers (2) (not shown) to the fuel priming pump
with banjo bolt (1) .
6. Tighten banjo bolt (1) to a torque of 20 to 25 N·m (15 to 18 lb ft).
3/4(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 13 08:47:26 UTC+0800 2019
4/4(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR HKT
Configuration: 320C & 320C L Excavators HKT00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564836
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/4(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813127
1. Use Tool (A) to remove fuel filter (3) from fuel filter base (2) .
Note: It is not necessary to remove the fuel filter in order to remove the fuel filter base.
2. Remove banjo bolts (1) and copper washers in order to disconnect the fuel lines (4) from the
fuel filter base (2).
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
Illustration 2 g00813147
3. Remove two bolts (5) and the washers that secure the fuel filter base (2) to the air inlet
manifold. Remove the fuel filter base (2) from the fuel filter bracket.
Installation Procedure
2/4(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00813147
1. Place the fuel filter base (2) in position on the fuel filter bracket. Install the washers and two
bolts (5) that secure the fuel filter base tothe fuel filter bracket.
Illustration 4 g00813127
2. Install the banjo bolts (1) and install new copper washers in order to connect the fuel lines
(4) to the fuel filter base (2) .
3. If the fuel filter was removed, install the fuel filter (3) to the fuel filter base (2). Tighten the
fuel filter by hand according to the instructions that are shown on the fuel filter. Do not
overtighten the fuel filter.
3/4(W)w
2019/9/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...