The document provides instructions for removing and installing a fuel injector on a C1.3 engine. To remove the fuel injector, the fuel lines must first be removed. Then the overflow pipe, nuts, copper washers and fuel injector are removed. The copper gasket and heat seal are also removed. To install the fuel injector, a new copper gasket and heat seal are placed in the cylinder head first. Then the fuel injector, copper washers and overflow pipe are installed and the nuts are tightened. Finally, the fuel lines are reinstalled.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 303E CR MINI HYD EXCAVATOR SMG
Configuration: 303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1.3 Engine
Disassembly and Assembly
C1.3 Engine for Caterpillar Built Machines
Media Number -UENR3292-03 Publication Date -01/05/2014 Date Updated -02/02/2017
i05317149
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1859 Retaining Ring Pliers 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g03381347
1. Before removing the governor assembly, align the timing marks on all gears on the front of
the engine.
Illustration 2 g03370058
1. Remove bolts (1) and speed control plate (2). Remove stop solenoid (2A).
Illustration 3 g03370061
2. Disconnect governor spring (3) from speed control plate (2). Remove governor spring (3).
2/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g03370069
3. Remove start spring (4) from thrust lever (5).
Illustration 5 g03370075
Illustration 6 g03381361
4. Remove bolts (6) and injector pump (7). Align the control rack pin (7A) with the notch in
the crankcase (7B).
Illustration 7 g03370082
5. Remove plug (8).
3/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g03370176
Illustration 9 g03370186
6. Measure the height of max torque limiter (8) from block and record for installation
purposes. Remove max torque limiter (8).
Illustration 10 g03370189
4/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g03370193
7. Remove plate (10). Use bolt (1) in order to pull shaft (12) and bearing collar (11) from the
governor housing.
Illustration 12 g03370379
8. Remove fork lever assembly (13) from the governor housing.
Illustration 13 g03370397
9. Remove fuel camshaft stopper (14) and fuel camshaft gear assembly (15).
5/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 14 g03370400
Illustration 15 g03370402
Illustration 16 g03370401
10. Remove plug (16). Using Tooling (A) remove retaining ring (17). Remove governor shaft
and gear assembly (18).
6/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 17 g03370504
11. Remove setscrew (19) and bearing (20). Remove bearing (21).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 19:05:46 UTC+0800 2020
7/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 303E CR MINI HYD EXCAVATOR SMG
Configuration: 303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1.3 Engine
Disassembly and Assembly
C1.3 Engine for Caterpillar Built Machines
Media Number -UENR3292-03 Publication Date -01/05/2014 Date Updated -02/02/2017
i05318443
Governor - Install
SMCS - 1264-012
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1859 Retaining Ring Pliers 1
B 442-0744 Bushing Tool 1
C - Loctite 593 Silicone Sealer
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g03370555
Illustration 2 g03381410
1. Install bearing (20). Apply Tooling (C) to set screw (19). Install set screw (19) until the
tapered part contacts the bearing (20) as shown. Using Tooling (B), install bearing (21).
Illustration 3 g03370558
2/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 4 g03370578
Illustration 5 g03370582
2. Install governor shaft and gear assembly (18). Install retaining ring (17) on shaft. Install
plug (16).
Illustration 6 g03370616
3. Install fuel camshaft gear assembly (15). Make sure to line up timing marks on gears upon
installation. Install fuel camshaft stopper (14).
3/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 7 g03370617
4. Install fork lever assembly (13) into the governor housing.
Illustration 8 g03370618
Illustration 9 g03370620
5. Use bolt (1) in order to install shaft (12) into the governor housing and fork lever assembly
(13). Install bearing collar (11). Install plate (10).
4/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 10 g03370636
Illustration 11 g03370637
6. Install max torque limiter (9) to the Pre measured height recorded from disassembly.
Illustration 12 g03370639
7. Apply Tooling (C) on plug (8). Install plug (8).
5/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 13 g03381440
Illustration 14 g03370640
Note: Addition or reduction of shims 0.05 mm (0.002 inch) delays or advances the
injection timing by approximately 0.0087 rad (0.5). In disassembling and replacing, be
sure to use the same thickness of new shims that are being replaced.
8. Place new shims (7) to the amount of thickness recorded from the removal procedure. When
installing injection pump (6) insert the rack pin into the groove (6) of the thrust lever on the
fork. Install injector pump (5). Install the bolts.
Illustration 15 g03370658
6/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 9. Install start spring (4) onto the thrust lever.
Illustration 16 g03370659
10. Install governor spring (3). Connect governor spring (3) to speed control plate (2).
Illustration 17 g03370660
11. Place Tooling (C) onto the mounting surface of speed control plate (2). Install speed control
plate (2). Install bolts (1). Place Tooling (C) on stop solenoid (2A). Install stop solenoid
(2A).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 19:06:43 UTC+0800 2020
7/7
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 303E CR MINI HYD EXCAVATOR SMG
Configuration: 303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1.3 Engine
Disassembly and Assembly
C1.3 Engine for Caterpillar Built Machines
Media Number -UENR3292-03 Publication Date -01/05/2014 Date Updated -02/02/2017
i05319637
Fuel Injection Pump - Remove and Install
SMCS - 1251-010
Removal Procedure
Start By:
a. Remove fuel injection lines.
Illustration 1 g03371180
1. Remove solenoid (1). Remove bolts (2) and speed control plate (3).
1/4
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g03371184
2. Remove start spring (4).
Illustration 3 g03371170
Illustration 4 g03371249
3. Remove bolts (5) and fuel injection pump (6).
4. When removing the injection pump, align the control rack pin with the notch.
5. Remove shims (7) from under fuel injection pump (6). Record the number and thickness of
shims (7) for installation purposes.
2/4
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Installation Procedure
Illustration 5 g03371238
1. Place new shims (7) to the amount of thickness recorded from the removal procedure. When
installing injection pump (6) align the control rack pin with the notch. Insert the rack pin
into groove (8) of the thrust lever on the fork.
Note: Addition or reduction of shims 0.05 mm (0.002 inch) delays or advances the
injection timing by approximately 0.0087 rad (0.5). In disassembling and replacing, be
sure to use the same thickness of new shims that are being replaced.
Illustration 6 g03371259
2. Install fuel injection pump (6). Install bolts (5).
3/4
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 7 g03371269
3. Install start spring (4).
Illustration 8 g03371286
4. Install speed control plate (3) and bolts (2). Install solenoid (1).
End By:
a. Install the fuel injection lines.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 19:07:40 UTC+0800 2020
4/4
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 303E CR MINI HYD EXCAVATOR SMG
Configuration: 303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1.3 Engine
Disassembly and Assembly
C1.3 Engine for Caterpillar Built Machines
Media Number -UENR3292-03 Publication Date -01/05/2014 Date Updated -02/02/2017
i05350824
Fuel Injector - Remove and Install
SMCS - 1290-010
Removal Procedure
Start By:
a. Remove the fuel injection lines
Note: Use caution in removing the line fittings on the fuel injection pump. Hold the fuel
injector line fitting stationary to avoid turning and causing leaks from the fuel injector
pump.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/4
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
23. Illustration 4 g03389436
4. Remove copper gasket (6) and heat seal (7).
Installation Procedure
Note: Replace copper gasket (6) and heat seal (7) with new upon installation.
Illustration 5 g03389445
1. Place heat seal (7) and copper gasket (6) in the cylinder head.
Illustration 6 g03389452
3/4
303E CR Mini Hydraulic Excavator SMG00001-UP (MACHINE) POWERED BY C1....
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...