This document provides instructions for disassembling and assembling components of the rear axle, differential, and final drive of a 12M 2 Motor Grader. It lists 48 steps to remove parts like the rear axle, sprockets, bearings, housings, gears, seals, and more. Special tools are required to remove some components. Technicians should note the order and quantity of shims and other parts during disassembly.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Power Train
Media Number -KENR8899-03 Publication Date -01/05/2017 Date Updated -18/05/2017
i06013976
Rear Axle, Differential and Final Drive - Disassemble
SMCS - 3258-015; 3278-015; 3282-015-RE; 4050-015; 4068-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 4
B 140-7742 Sleeve 2
C 386-6031 Lever Puller Hoist 1
D 154-6182 Forcing Bolt 3
E 439-3939 Link Bracket 2
F
8B-7551 Bearing Puller Gp 1
1P-5546 Crossarm 1
3H-0465 Push-Puller Plate 2
5F-7366 Forcing Screw 1
G 292-4949 Socket Wrench As 1
H 154-6183 Forcing Bolt 3
J 1U-6405 Three Jaw Puller 1
Start By:
A. Remove the rear axle.
1/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
Illustration 1 g01413868
1. Use Tooling (A) , Tooling (B) , and two suitable lifting devices in order to position rear axle
(1) onto suitable blocking. The weight of rear axle (1) is approximately 1089 kg (2400 lb).
Illustration 2 g01418559
2/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. 2. Remove bolts (3) , retainer (4) , shims (5) , sprocket (2) , and sprocket (6) .
Note: Note the quantity and the order of shims (5) .
Illustration 3 g01414357
3. Remove bearing cone (7) .
Illustration 4 g01412778
3/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 4. Attach Tooling (A) , Tooling (C) , and two suitable lifting devices onto final drive housing
(8) . The weight of final drive housing (8) is approximately 191 kg (420 lb). Remove nuts
(9) and bolts (9A) .
5. Use Tooling (D) in order to remove final drive housing (8) .
Illustration 5 g01419912
6. Remove bolts (10) . Remove retainer (11) .
Illustration 6 g01352280
7. Remove shims (12) . Use Tooling (A) and a suitable lifting device in order to remove
housing (13) . The weight of housing (13) is approximately 54 kg (120 lb).
Note: Note the quantity and the order of shims (12) .
4/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 7 g01352292
8. Remove thrust washer (14) . Remove wear sleeves (15) .
Illustration 8 g01352299
9. Turn over housing (13) . Remove lip seal (16) .
Illustration 9 g01414353
10. Remove bearing cup (17) . Remove thrust washer (18) .
5/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 10 g01352320
11. Remove lip seal (19) . Remove bearing cup (20) .
Illustration 11 g01419983
12. Use Tooling (E) in order to remove carrier assembly (21) and drive shaft (22) . The weight
of carrier assembly (21) and drive shaft (22) is approximately 136 kg (300 lb).
6/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 12 g01419985
13. Use Tooling (F) in order to remove bearing cone (23) .
Illustration 13 g01352339
14. Remove retaining ring (24) in order to remove axle shaft (22) from carrier assembly (21) .
Illustration 14 g01352406
15. Remove bolts (25) and retainer (26) . Remove pin (27) . Remove gear (28) . Remove thrust
washers (29) and bearings (30) . Repeat this step for the remaining planetary gears.
7/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 15 g01352384
16. Remove axle shaft assembly (31) .
Illustration 16 g01352402
17. Remove retaining ring (32) in order to remove gear (33) from axle shaft (34) .
Illustration 17 g01352438
18. Use Tooling (D) in order to separate ring gear (35) from the intermediate housing.
8/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 18 g01352445
19. Use Tooling (B) and a suitable lifting device in order to remove ring gear (35) . The weight
of ring gear (35) is approximately 25 kg (55 lb).
20. Repeat Step 2 through Step 19 for the opposite side.
Illustration 19 g01353587
21. Position differential housing (36) with intermediate housing (37) upward.
9/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 20 g01419994
22. Attach a suitable lifting device onto pinion (38) . Use Tooling (H) in order to separate
pinion (38) from the center housing. Remove bolts (39) in order to remove pinion (38) . The
weight of pinion (38) is approximately 56 kg (123 lb).
Illustration 21 g01353021
23. Remove shims (40) . Remove O-ring seal (41) .
Note: Note the order and the quantity of shims (40) .
10/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 22 g01353002
24. Remove bolt (42) . Remove retainer (43) . Remove yoke (44) . Remove guard (45) .
Illustration 23 g01353512
25. Remove shims (46) . Remove lip seal (47) .
Note: Note the order and the quantity of shims (46) .
Illustration 24 g01353570
26. Remove pinion (48) . Remove bearing cone (49) . Remove bearing cup (50) . Remove
bearing cone (51) . Remove bearing cup (52) .
27. Use Tooling (G) in order to remove nut assembly (54) .
11/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 25 g03772865
28. Remove bolts (53) . Remove bolts (54) .
Illustration 26 g01419996
Typical Example
29. Use Tooling (J) in order to separate intermediate housing (37) from differential housing
(36) .
12/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 27 g01420124
Typical Example
30. Use Tooling (E) in order to remove intermediate housing (37) . The weight of intermediate
housing (37) is approximately 32 kg (71 lb).
Illustration 28 g03772901
Typical Example
31. Before installing Tooling (A) remove the shims. Use Tooling (A) in order to remove
bearing assembly (55) and differential (56) . The weight of bearing assembly (55) and
differential (56) is approximately 102 kg (225 lb).
13/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 29 g03772885
32. Remove bolts (57) . Remove shroud (58) .
Illustration 30 g03772948
33. Remove bolts (59) . Use Tooling (G) and remove lock-nut (60) .
Illustration 31 g03772966
34. Use Tooling (F) in order to remove bearing assembly (55) .
14/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 32 g01354900
35. Remove bearing cone (63) . Remove bearing cups (64) .
Illustration 33 g01420000
36. Use Tooling (J) in order to remove spacer (65) and bearing cone (66) .
Note: This step is a destructive procedure. Replace bearing cone (66) .
15/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 34 g01353751
37. Remove retaining ring (67) . Remove bearing race (68) . Remove O-ring seals (69) .
Remove thrust ring (70) .
Illustration 35 g01353760
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
38. Remove bolts (71) . Remove case (72) .
16/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 36 g01353766
39. Remove thrust washer (73) . Remove plates (74) and discs (75) . Remove springs (76) .
Note: Note the quantity and the order of plates (74) and discs (75) .
Illustration 37 g01353940
40. Remove housing (77) .
Illustration 38 g01353944
41. Remove differential gear (78) .
17/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 39 g01353945
42. Remove spider assembly (79) .
Illustration 40 g01353954
43. Remove thrust washer (80) , pinion gear (81) , and bearing sleeve (82) from spider (83) .
Repeat this step for the remaining pinion gears (81) .
Illustration 41 g01353965
18/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. 44. Remove differential gear (84) . Remove thrust washer (85) .
Illustration 42 g01353970
45. Use two people in order to turn over housing (86) and bevel gear (87) . The combined
weight of housing (86) and bevel gear (87) is approximately 59 kg (130 lb). Remove bolts
(88) . Use two people in order to remove housing (86) from bevel gear (87) . The weight of
housing (86) is approximately 41 kg (90 lb). The weight of bevel gear (87) is approximately
19 kg (41 lb).
Illustration 43 g01355203
46. Remove bearing assembly (89) . Remove piston (90) .
19/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 44 g01355208
47. Remove thrust race (91) , thrust bearing (92) , and thrust race (93) from piston (90) .
Illustration 45 g01355211
48. Remove seals (94) from piston (90) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 6 10:17:50 UTC+0800 2021
20/20
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12M 2 MOTOR GRADER F9M
Configuration: 12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Power Train
Media Number -KENR8899-03 Publication Date -01/05/2017 Date Updated -18/05/2017
i07285127
Rear Axle, Differential and Final Drive - Assemble
SMCS - 3258-016; 3278-016; 3282-016-RE; 4050-016; 4068-016
Assembly Procedure
Table 1
Required Tools
Tool
Part
Number
Part Description Qty
A 439-3940 Link Bracket 4
B 140-7742 Sleeve 2
C 386-6031 Lever Puller Hoist 1
E 143-3939 Link Bracket 2
G 292-4949 Socket Wrench As 1
H 154-6183 Forcing Bolt 2
K 4C-4030 Thread Lock Compound 1
L 1U-8846 Gasket Sealant 1
M
6V-2012 Depth Micrometer 1
367-9109 Caliper(1)
1
N
8T-5096 Dial Indicator Gp 1
301-3405 Gauge 1
P 8T-4140 Bolt 4
R 7M-7456 Bearing Mount Compound 1
1/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. S - Cat Advance 3Moly Grease or Dow Corning Molykote BR2 -
Plus
1
T 8T-5096 Dial Indicator Gp 1
(1)
For use with three bolt retainers
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals, gaskets, and lip seals. Replace O-ring seals, gaskets, and lip seals
that are worn or damaged.
Note: Lubricate O-ring seals and lip seals with the lubricant that is being sealed.
Illustration 1 g03831520
1. Install seals (94) onto piston (90).
Illustration 2 g03831488
2/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Note: Grease is used to hold thrust race (93) and thrust bearing (92) in place during
assembly.
2. Apply a liberal amount of grease to thrust race (93) and to thrust bearing (92). Install thrust
race (93) and thrust bearing (92) onto piston (90).
Illustration 3 g01355203
3. Install piston (90). Lower the temperature of bearing assembly (89). Install bearing
assembly (89).
Illustration 4 g01353970
4. Use two people to install housing (86) onto bevel gear (87). The weight of housing (86) is
approximately 41 kg (90 lb). Install bolts (88). Tighten bolts (88) to a torque of
300 ± 40 N·m (221 ± 30 lb ft).
5. Use two people to turn over bevel gear (87) and housing (86). The combined weight of
bevel gear (87) and housing (86) is approximately 59 kg (130 lb).
3/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 5 g01353965
6. Install thrust washer (85). Install differential gear (84).
Note: Install thrust washer (85) with the groove side against gear (84).
Illustration 6 g01353954
7. Install bearing sleeve (82), pinion gear (81), and thrust washer (80) onto spider (83). Repeat
this step for the remaining pinion gears (81).
Illustration 7 g01353945
8. Install spider assembly (79).
4/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 8 g01353944
9. Install differential gear (78).
Illustration 9 g01353940
10. Install housing (77).
Note: Ensure that the notches on the housings are aligned.
Illustration 10 g01353766
5/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. 11. Install plates (74) and discs (75). Install thrust washer (73). Install springs (76).
Note: Lubricate the discs with the lubricant that is being sealed.
Note: Install thrust washer (73) with the groove side against the gear.
Illustration 11 g01353760
Typical Example
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Determine bolt size before torquing bolts (71).
12. Install case (72). Install bolts (71). Tighten M16 bolts (71) to a torque of 300 ± 40 N·m
(220 ± 30 lb ft). Tighten M12 bolts (71) to a torque of 120 ± 20 N·m (90 ± 15 ft)
6/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Illustration 12 g03831494
Note: Grease is used to hold thrust race (91) in place during assembly.
13. Install thrust ring (70). Apply a liberal amount of grease to thrust race (91). Install thrust
race (91) onto thrust ring (70). Install O-ring seals (69). Raise the temperature of bearing
race (68). Install bearing race (68). Install retaining ring (67).
Illustration 13 g01354921
14. Raise the temperature of bearing cone (66). Install bearing cone (66) and spacer (65).
Illustration 14 g06240309
15. Use a suitable press to install bearing assembly (55). Install shroud (58). Apply Tooling (K)
to the threads of bolts (57) and install bolts (57). Tighten bolts (57) to a torque of
28 ± 7 N·m (21 ± 5 lb ft).
7/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 15 g03773005
16. Use Tooling (G) to Install nut assembly (60). Tighten nut assembly (60) to a torque of
300 ± 40 N·m (221 ± 30 lb ft).
17. Install bolts (59). Tighten bolts (59) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 16 g03772901
Typical Example
18. Use Tooling (A) and a suitable lifting device to install bearing assembly (55) and
differential (56). The weight of bearing assembly (55) and differential (56) is approximately
102 kg (225 lb).
19. Remove Tooling (A) and install shims that are equal to 2.29 mm (0.09 inch).
8/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
30. Illustration 17 g01420124
Typical Example
20. Use Tooling (E) and a suitable lifting device to install intermediate housing (37). The
weight of intermediate housing (37) is approximately 32 kg (71 lb).
Illustration 18 g03772865
21. Install bolts (54). Tighten bolts (54) to a torque of 300 ± 40 N·m (221 ± 30 lb ft). Install
bolts (53). Tighten bolts (53) to a torque of 105 ± 20 N·m (77 ± 15 lb ft).
Illustration 19 g01353570
22. Lower the temperature of bearing cup (52). Install bearing cup (52). Lower the temperature
of bearing cup (50). Install bearing cup (50). Raise the temperature of bearing cone (49).
Install bearing cone (49) onto pinion gear (48). Install pinion (48). Install bearing cone (51).
Note: Lubricate the splines of the pinion shaft prior to assembly.
Note: Lubricate bearing cups and cones with the lubricant being sealed prior to assembly.
9/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Engin...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
31. Note: Use a 0.04 mm (0.0015 inch) feeler gauge to check bearing cups (50) and (52), and
bearing cone (49). If the bearing cups and cones are completely seated, the feeler gauge will
not fit.
Illustration 20 g01353512
Illustration 21 g01353002
23. Install guard (45), yoke (44), and the original shim pack (46). Install retainer (43) and bolt
(42). Tighten bolt (42) to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
24. Measure the rolling torque. Add or remove shims to obtain a rolling torque measurement of
1.2 ± 0.5 N·m (10.5 ± 4.5 lb in).
Note: Loosen the bearing after the rolling torque is measured and shims are added or
removed.
25. Remove bolt (42), retainer (43), and shims (46). Remove yoke (44) and guard (45).
26. Install lip seal (47) and guard (45). Install yoke (44), shims (46), and retainer (43). Install a
new bolt (42). Tighten the new bolt (42) to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
Note: Lubricate the seal and the shaft prior to installation.
10/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
32. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
33. Illustration 22 g01353021
27. Install a number of shims (40) that is equal to 1.78 mm (0.07 inch). Do not install O-ring
seal (41) at this time.
Illustration 23 g01355005
28. Use a suitable lifting device to install pinion (38). The weight of pinion (38) is
approximately 56 kg (123 lb). Install bolts (39). Tighten bolts (39) to a torque of
270 ± 40 N·m (199 ± 30 lb ft).
Note: Lubricate the O-ring seal, the shaft, and the bore with the lubricant that is being
sealed prior to assembly.
11/27
12M Series 2 Motor Grader F9M00001-UP (MACHINE) POWERED BY C9.3 Eng...
2021/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...