This document provides instructions for removing and installing an implement hydraulic pump on a 120H motor grader. It begins with safety procedures for releasing pressure from the hydraulic system. It then provides detailed steps to remove the pump and its components. The installation section provides the reverse steps and specifies torque specifications for reinstalling the pump. It also describes how to disassemble and assemble the internal components of the implement hydraulic pump.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120H MOTOR GRADER 6TM
Configuration: 120H Motor Grader 6TM00001-00442 (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
120H & 135H MOTOR GRADERS MACHINE SYSTEM
Media Number -SENR8544-01 Publication Date -01/10/2004 Date Updated -04/02/2016
SENR85440036
Implement Hydraulic Pump
SMCS - 5070-011; 5070-012; 5070-017
Remove Implement Hydraulic Pump
1. Articulate the machine to the right in order to achieve working space.
2. Release pressure in the hydraulic system as follows:
At operating temperature, the hydraulic oil is hot and under pressure.
Hot oil can cause burns. Sudden movement of the machine or release of
oil pressure can cause injury to persons on or near the machine. To
prevent possible injury, perform the following procedure before
working on the hydraulic and steering systems.
a. Move the machine to a smooth horizontal location. Move away from working machines and
personnel. Lower all implements to the ground. Install the wheel lean pin in front axle.
b. Permit only one operator on the machine. Keep all other personnel either away from the
machine or in view of the operator.
c. Activate the parking brake. Place all implements on the ground and put the blade in the
"FLOAT" position.
d. Stop the engine.
e. Turn the steering wheel back and forth several times to relieve pressure in the steering
accumulator.
f. Carefully loosen the filler cap on the hydraulic tank to release pressure in the tank.
1/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. g. Be sure all hydraulic pressure is released before any fitting, hose, or component is loosened,
tightened, removed or adjusted.
h. Tighten the cap on the hydraulic tank.
i. The pressure in the hydraulic system must be released before lines or components can be
removed.
Hydraulic pressure can exist in the hydraulic lines between the control
valves and the cylinders with the engine stopped. Manually relieve
pressure before working on any hydraulic circuit.
3. Drain hydraulic system. Remove plug from ecology drain at the bottom of the oil tank. Drain
the hydraulic oil in a suitable container for storage or disposal. The capacity of the hydraulic oil
tank is 63 liters (16.8 U.S. gal).
4. Remove bolts (1), (3) and the washers that hold two split shields (2) together and to the machine
frame.
5. Remove bolts (4) and the washers from pump drive shaft (5). Remove pump drive shaft (5)
from the implement hydraulic pump.
2/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 6. Remove tube assembly (6) from valves (8) & (10).
7. Remove cap screws (9) that holdcompensator valve (10) to the implement hydraulic pump.
Remove compensator valve (10) from the implement hydraulic pump.
8. Remove bolts (7) and the washers that hold combination valve (8) to the implement hydraulic
pump. Remove combination valve (8) from the implement hydraulic pump.
9. Remove bolts (11) from elbow (12). Move elbow (12) and its seal from the implement
hydraulic pump.
10. Remove hose assembly (14) from implement hydraulic pump (13).
11. Remove nut (18) and the washer from the implement hydraulic pump shaft.
12. Remove yoke (16) from implement hydraulic pump (13).
13. Remove bolts (15) and the washers that hold bracket (15) to implement hydraulic pump (13).
14. Remove mounting bolts (19), the washers and rubber mountings (20) that hold mounting
bracket (17) to the machine frame. Remove mounting bracket (17) from the machine frame.
15. Use a lifting sling and a hoist, or a power truck in order to remove implement hydraulic pump
(13) from the left side of the vehicle. the weight of implement hydraulic pump (13) is 50 Kg (110
lb).
3/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Install Implement Hydraulic Pump
1. Make sure that all components of the implement Hydraulic Pump and the matching components
are clean prior to installation of the pump. During the installation of the Implement Hydraulic
Pump, check the condition of all O-ring seals used in the assembly. If any of the seals are
damaged, use new parts for replacement.
2. Position implement hydraulic pump (13) to the machine frame.
3. Position mounting bracket (17) to the machine frame and to implement hydraulic pump (13).
4. Install rubber mounts (20), bolts (16) and the washers that that hold mounting bracket (17) to
the machine frame.
5. Install bolts (15) and the washers that hold bracket (15) to implement hydraulic pump (13).
Tighten bolts (15) to a torque of 160 ± 30 N·m (118 ± 22 lb ft).
6. Install yoke (16), nut (18) and the washer to implement hydraulic pump (13). Tighten nut (18)
to a torque of 190 ± 25 N·m (140 ± 18 lb ft).
7. Install hose assembly (14) to implement hydraulic pump (13).
8. Position elbow (12) and its seal to implement hydraulic pump (13). Install bolts (11) that hold
elbow (12) to implement hydraulic pump (13).
4/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 9. Position combination valve (8) to implement hydraulic pump (13). Install bolts (5) and the
washers that hold combination valve (8) to implement hydraulic pump (13).
10. Position compensator valve (10) to implement hydraulic pump (13). Install cap screws (9) that
hold compensator valve (10) to implement hydraulic pump (13).
11. Install assembly (6) to valves (8) and (10).
12. Position pump drive shaft (5) to implement hydraulic pump (13). Install bolts (3) and the
washers that hold pump drive shaft (5) to implement hydraulic pump (13).
13. Position two split shields (2) over drive shaft (5). Install bolts (1), (3) and the washers that
hold the guards together and to the machine frame. Tighten bolts (3) to a torque of 135 ± 20 N·m
(99 ± 15 lb ft).
14. Fill the hydraulic oil system with the proper amount of hydraulic oil. Refer to the "Operation
& Maintenance Manual" for the proper oil, procedure and amount of oil.
Disassemble & Assemble Implement Hydraulic Pump
5/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Start By:
a. remove implement hydraulic pump
1. Remove bolts (1) from valve group (2). Remove valve group (2) from the implement pump.
2. Remove bolts (4) and cover (5) from housing (3).
3. Remove O-ring seal (6) from housing (3).
6/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 4. Remove plug (7) and the O-ring seal from head (8). Slowly and evenly remove five bolts (10)
and bolt (9), in order to release the spring force on the valve assembly.
5. Remove head (8) and the gasket from housing (3).
6. Remove piston (12) and spring (13) from piston rod (11).
7. Remove piston (15) from piston rod (14).
8. Remove pin (16) from head (8).
9. Remove piston rod (11) from head (8).
10. Remove piston rod (14) from head (8).
11. Use Tooling (A) in order to remove bearing cup (17) from head (8).
7/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 12. Remove bearing (19), shims (18) that are underneath the bearing, and plate (20) from the
pump group. Remove two pins (Z) from the pump housing.
13. Remove four bolts (24), two locking plates (23) and two spacer plates (22) from swashplate
(21).
14. Remove swashplate plug (25) and its O-ring seal from housing (3).
15. Remove rotating group (26) and shim kit (27) from housing (3).
Rotating Group (26)
16. Put identification marks on nine pistons (28), in relationship to barrel (29) and plate (30), for
assembly purposes. Remove nine piston assemblies (28) and plate (30) from barrel (29).
8/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Spring (33) is under pressure. Release the spring pressure slowly in
order to avoid personal injury.
17. Use Tooling (D) and a press in order to compress spring (33). Use Tooling (B) in order to
remove snap ring (31) from barrel (29).
18. Remove snap ring (31), spacer (34), spring (33), and spacer (32) from barrel (29).
19. Note the orientation of swashplate (21) in relationship to housing (3) for assembly purposes.
Remove swashplate (21), shaft (36), and bearing (35) from housing (3).
9/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 20. Remove bearing (35) from shaft (36).
21. Remove shield (37) from housing (3).
22. Use Tooling (B) in order to remove snap ring (38) from housing (3). Remove lip-type seal (39)
from housing (3).
23. Remove two screws (42), bearing (40) and bearing (41) from housing (3).
24. Use Tooling (C) in order to remove roller bearing cup (43) from housing (3).
NOTE: The following steps are for the assembly of the implement hydraulic pump.
10/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. NOTE: If a new swashplate, swashplate bearings, shaft, shaft bearings, head or housing are
installed, axial end play must be set. Refer to the topic "Shaft Bearing Endplay Adjustment" in the
Specifications Manual, SENR8509 and SENR8557.
25. During the assembly of the implement hydraulic pump, check the condition of all the O-ring
seals and the lip seals that are used in the pump. If any of these seals are damaged, use new parts
for replacement.
26. Lower the temperature of bearing cup (17). Use Tooling (D) in order to install bearing cup
(17) in head (8). Install bearing cup (17) until it is seated.
27. Lower the temperature of bearing cup (43). Use Tooling (D) in order to install bearing cup
(43) in housing (3). Install bearing cup (43) until it is seated.
28. Install bearing (35) in housing (3).
29. Install bearing (40), bearing (41), and setscrews (42) to housing (3).
30. Use Tooling (D) in order to install lip seal (39) in housing (3) until it is seated. The sealing lip
must face inward. Lubricate the sealing lip lightly with hydraulic oil. Use Tooling (B) in order to
install Retention ring (38) in housing (3).
11/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 31. Install shield (37) to housing (3).
32. Put a light coat of hydraulic oil on bearings (41) and (42) in order to hold swashplate (21) in
position during the next steps of assembly. Install swashplate (21) in housing (3) and in bearings
(41) and (42).
33. Block up housing (3) in order to have clearance when shaft (36) is installed. Shaft (36) extends
beyond the end of housing (3). Install shaft (36) through swashplate (21), in bearing (35) and
housing (3).
12/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 34. Install plug (25) and O-ring seal in housing (3). Tighten Plug (25) to a torque of 102 ± 4 N·m
(75 ± 3 lb ft).
35. Install spacer (32), spring (33) and spacer (34) in barrel (29).
36. Use Tooling (D) and a shop press in order to compress spring (33).
37. Use Tooling (B) to install snap ring (31) in barrel (29).
38. Install nine pistons (28) in their original locations in spacer (30) and barrel (29). This is easier
accomplished if the barrel is set in an upright position and then the pistons, already in the spacer,
are inserted from above.
13/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. 39. Lay housing (3) on its side. Install rotating group (26) and shim kit (27) on shaft (36) and in
housing (3).
40. Install bearing (19) and shims (18) to shaft (36).
41. Position two spacers (22) and two locking plates (23) to their original positions on swashplate
(21).
42. Apply 9S-3263 Compound on bolts (24). Install four bolts (24) in order to hold plates (23)
and spacers (22) to swashplate (21). Tighten bolts (24) to a torque of 34 ± 3 N·m (25 ± 2 lb ft).
43. Install pin (16) in head (8).
44. Apply 9S-3263 Compound to piston rods (11) and (14).
14/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 45. Install piston rods (11) and (14) in head (8). Tighten piston rods (11) and (14) to a torque of 79
± 4.0 N·m (58 ± 3 lb ft).
46. Install spring (13), piston (12) and piston (15) to head (8).
47. Use a light coat of 5N-5561 Silicone Lubricant in order to hold plate (20) to head (8) during
assembly.
48. Position head (8) and the gasket on housing (3) and bearing (19).
49. Install bolts (9) and (10) in order to hold head (8) to housing (3). Slowly and evenly tighten the
bolts to a torque of 91 ± 4 N·m (67 ± 3 lb ft).
50. Install plug (7) and O-ring seal in head (8). Tighten plug (7) to a torque of 12.9 ± 0.1 N·m (10
± .1 lb ft).
15/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 51. Install O-ring seal (6) to housing (3).
52. Install plate (5) and bolts (4) to housing (3). Tighten bolts (4) to a torque of 8.5 ± 1.0 N·m (6
± .8 lb ft).
53. Install valve group (2) and bolts (1) to the pump.
End By:
a. install implement hydraulic pump
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Mar 24 13:05:25 UTC+0800 2020
16/16(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120H MOTOR GRADER 6TM
Configuration: 120H Motor Grader 6TM00001-00442 (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
120H & 135H MOTOR GRADERS MACHINE SYSTEM
Media Number -SENR8544-01 Publication Date -01/10/2004 Date Updated -04/02/2016
SENR85440037
Implement Control Valves
SMCS - 5051-016; 5051-011; 5051-012; 5051-015
Remove Implement Control Valves
1. Release the pressure in the hydraulic system as follows:
At operating temperature, the hydraulic oil is hot and under pressure.
Hot oil can cause burns. Sudden movement of the machine or release of
oil pressure can cause injury to persons on or near the machine. To
prevent possible injury, perform the following procedure before
working on the hydraulic and steering systems.
a. Move the machine to a smooth horizontal location. Move away from working machines and
personnel. Lower all implements to the ground. Install the wheel lean pin in front axle.
b. Permit only one operator on the machine. Keep all other personnel either away from the
machine or in view of the operator.
c. Activate the parking brake. Place all implements on the ground and put the blade in the
"FLOAT" position.
d. Stop the engine.
e. Turn the steering wheel back and forth several times to relieve pressure in the steering
accumulator.
f. Carefully loosen the filler cap on the hydraulic tank to release pressure in the tank.
1/14(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. g. Be sure all hydraulic pressure is released before any fitting, hose, or component is loosened,
tightened, removed or adjusted.
h. Tighten the cap on the hydraulic tank.
i. The pressure in the hydraulic system must be released before lines or components can be
removed.
Hydraulic pressure can exist in the hydraulic lines between the control
valves and the cylinders with the engine stopped. Manually relieve
pressure before working on any hydraulic circuit.
2. Put identification marks on hose assemblies (1) for installation purposes. The number of control
valves and hoses will vary with the amount of implements on the machine.
3. Remove hose assemblies (1) from the implement control valves. Plug the fittings on the hoses
in order to prevent the loss of hydraulic oil, and to keep dirt out of the hydraulic oil system.
4. Remove bolts (2) from cover (3). Raise cover (3) up and out of the way. Pull floor mat (4) back
and out of the way.
2/14(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 5. Remove four bolts (7) from control valve linkages (8). Move four control valve linkages (8) up
and out of the way.
6. Remove bolts (5) and the washers from cover (6). Remove cover (6) from the floor of the cab.
7. Remove bolts (9), bolt (10), the washers, the nuts and the rubber mountings that hold the
implement control valves. Remove the implement control valves from the mounting plates.
8. Repeat Steps 2 through 7 for the implement control valves located on the other side of the
machine.
Install Implement Control Valves
1. Make sure all of the components of the implement control valves are clean prior to installation.
During the installation, check condition of all the O-ring seals used on the hydraulic hoses that
were disconnected. If any of these seals are damaged, use new parts for replacement.
2. Position the implement control valves to their original locations and install bolts (9), bolt (10),
the washers, the nutsand the rubber mountings in order to secure the valves to the mounting plates.
3/14(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 3. Install cover (6), bolts (5) and washers that hold cover (6) to the floor of the cab.
4. Install control valve linkages (8) and bolts (7) that hold the linkages to the implement control
valves.
5. Position floor mat (4) to its original location on the floor of the cab. Install cover (3) and bolts
(2).
6. Install hose assemblies (1) to their original locations on the implement control valves.
7. Repeat Steps 2 through 6 for the other side.
8. Fill the hydraulic tank with oil to its correct level. Refer to the "Operation & Maintenance
Manual" for the proper procedure.
Disassemble Implement Control Valve
Start By:
a. remove implement control valve
4/14(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. 1. Put identification marks on cover (2), valves (5) and manifold (4), showing the location of the
components, for assembly purposes. Remove bolts (1) and cover (2) from the control valve.
2. Remove bolts (3) and manifold (4) from the control valve.
NOTE: The number of valves may vary in order to match the number of implements.
3. Separate individual valves (5) and seal plates (6) from the unit.
4. Remove bolts (7) and washers from valve (5).
5. Remove cover (9), O-ring seal (10) and spring (11) from valve (5).
5/14(W)w
2020/3/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...