The document provides instructions for removing the engine and crankcase assembly from various Case IH tractor models. It details disconnecting various components like the air intake lines, fuel lines, coolant lines, electrical connections, and exhaust components. Special lifting equipment is required to remove heavy parts like the diesel oxidation catalyst.

1. Printed in U.S.A.
© 2018 CNH Industrial America LLC. All Rights Reserved.
Case IH is a trademark registered in the United States and many
other countries, owned or licensed to CNH Industrial N.V.,
its subsidiaries or affiliates.
Magnum™
180
Magnum™
200
Magnum™
220
Powershift Transmission (PST)
Tractor
PIN ZJRH04001 and above
Part number 51537962
1st
edition English
October 2018
SERVICE MANUAL

2. Link Product / Engine
Product Market Product Engine
Magnum™ 180 PST TIER 4B
[ZJRH04001 - ]
Australia New Zealand F4HFE613K*B002
Magnum™ 180 PST TIER 4B
[ZJRH04001 - ]
North America F4HFE613K*B002
Magnum™ 200 PST TIER 4B
[ZJRH04001 - ]
North America F4HFE613J*B005
Magnum™ 200 PST TIER 4B
[ZJRH04001 - ]
Australia New Zealand F4HFE613J*B005
Magnum™ 220 PST TIER 4B
[ZJRH04001 - ]
Australia New Zealand F4HFE613H*B003
Magnum™ 220 PST TIER 4B
[ZJRH04001 - ]
North America F4HFE613H*B003
51537962 23/10/2018

3. Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
[10.216] Fuel tanks .......................................................................... 10.2
[10.218] Fuel injection system............................................................... 10.3
[10.202] Air cleaners and lines .............................................................. 10.4
[10.500] Selective Catalytic Reduction (SCR) exhaust treatment ........................... 10.5
[10.400] Engine cooling system ............................................................. 10.6
[10.414] Fan and drive ...................................................................... 10.7
[10.310] Aftercooler.......................................................................... 10.8
[10.304] Engine lubrication system.......................................................... 10.9
Power coupling........................................................................... 19
[19.100] Drive shaft.......................................................................... 19.1
[19.110] Flywheel damper ................................................................... 19.2
Transmission.............................................................................. 21
[21.113] Powershift transmission ............................................................ 21.1
[21.135] Powershift transmission external controls.......................................... 21.2
[21.155] Powershift transmission internal components...................................... 21.3
[21.160] Creeper ............................................................................ 21.4
[21.166] Overdrive........................................................................... 21.5
[21.200] Dropbox ............................................................................ 21.6
Four-Wheel Drive (4WD) system .................................................. 23
[23.202] Electro-hydraulic control ........................................................... 23.1
[23.304] Four-Wheel Drive (4WD) gearbox ................................................. 23.2
[23.314] Drive shaft.......................................................................... 23.3
Front axle system ....................................................................... 25
51537962 23/10/2018

4. [25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
[25.122] Axle suspension control............................................................ 25.4
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
Power Take-Off (PTO)................................................................. 31
[31.104] Rear electro-hydraulic control...................................................... 31.1
[31.114] Two-speed rear Power Take-Off (PTO) ............................................ 31.2
Brakes and controls .................................................................... 33
[33.202] Hydraulic service brakes ........................................................... 33.1
[33.110] Parking brake or parking lock ...................................................... 33.2
[33.220] Trailer brake hydraulic control...................................................... 33.3
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.102] Pump control valves................................................................ 35.2
[35.104] Fixed displacement pump.......................................................... 35.3
[35.105] Charge pump....................................................................... 35.4
[35.106] Variable displacement pump ....................................................... 35.5
[35.114] Three-point hitch control valve ..................................................... 35.6
[35.116] Three-point hitch cylinder .......................................................... 35.7
[35.204] Remote control valves ............................................................. 35.8
[35.300] Reservoir, cooler, and filters........................................................ 35.9
Hitches, drawbars, and implement couplings.................................. 37
[37.110] Rear three-point hitch .............................................................. 37.1
Frames and ballasting ................................................................. 39
[39.140] Ballasts and supports .............................................................. 39.1
51537962 23/10/2018

5. Steering..................................................................................... 41
[41.101] Steering control .................................................................... 41.1
[41.200] Hydraulic control components...................................................... 41.2
[41.206] Pump ............................................................................... 41.3
[41.432] Autoguidance steering ............................................................. 41.4
Wheels...................................................................................... 44
[44.520] Rear wheels........................................................................ 44.1
Cab climate control ..................................................................... 50
[50.100] Heating ............................................................................. 50.1
[50.200] Air conditioning..................................................................... 50.2
[50.300] Cab pressurizing system ........................................................... 50.3
Electrical systems....................................................................... 55
[55.010] Fuel injection system............................................................... 55.1
[55.011] Fuel tank system ................................................................... 55.2
[55.014] Engine intake and exhaust system................................................. 55.3
[55.024] Transmission control system....................................................... 55.4
[55.031] Parking brake electrical system .................................................... 55.5
[55.045] Front axle control system .......................................................... 55.6
[55.046] Rear axle control system........................................................... 55.7
[55.047] Steering control system ............................................................ 55.8
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system................. 55.9
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................. 55.10
[55.100] Harnesses and connectors....................................................... 55.11
[55.130] Rear three-point hitch electronic control system ................................. 55.12
[55.201] Engine starting system ........................................................... 55.13
[55.301] Alternator......................................................................... 55.14
[55.302] Battery............................................................................ 55.15
[55.408] Warning indicators, alarms, and instruments .................................... 55.16
51537962 23/10/2018

6. [55.512] Cab controls...................................................................... 55.17
[55.518] Wiper and washer system........................................................ 55.18
[55.640] Electronic modules ............................................................... 55.19
[55.988] Selective Catalytic Reduction (SCR) electrical system .......................... 55.20
[55.DTC] FAULT CODES.................................................................. 55.21
Platform, cab, bodywork, and decals............................................. 90
[90.100] Engine hood and panels ........................................................... 90.1
[90.102] Engine shields, hood latches, and trims ........................................... 90.2
[90.124] Pneumatically-adjusted operator seat.............................................. 90.3
[90.150] Cab................................................................................. 90.4
[90.151] Cab interior......................................................................... 90.5
[90.160] Cab interior trim and panels........................................................ 90.6
51537962 23/10/2018

7. INTRODUCTION
51537962 23/10/2018
1

8. Contents
INTRODUCTION
Foreword - Important notice regarding equipment servicing .................................... 3
Safety rules ..................................................................................... 4
Safety rules - General maintenance safety ..................................................... 5
Safety rules - Personal Protective Equipment (PPE) ........................................... 6
Safety rules - Do Not Operate tag .............................................................. 7
Safety rules - Ecology and the environment .................................................... 8
Torque - Minimum tightening torques for normal assembly ..................................... 9
Capacities ..................................................................................... 14
Product identification .......................................................................... 15
51537962 23/10/2018
2

9. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The information in this manual is up-to-date at the date of the publication. It is the policy of the manufacturer for
continuous improvement. Some information could not be updated due to modifications of a technical or commercial
type, or changes to the laws and regulations of different countries.
In case of questions, refer to your CASE IH Sales and Service Networks.
51537962 23/10/2018
3

10. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual and on machine decals, you will find the signal words DANGER, WARNING, and CAUTION
followed by special instructions. These precautions are intended for the personal safety of you and those working
with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. The
color associated with DANGER is RED.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
The color associated with WARNING is ORANGE.
CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury. The color associated with CAUTION is YELLOW.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation which, if not avoided, could result in machine or property damage. The color
associated with Notice is BLUE.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information which clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
51537962 23/10/2018
4

11. INTRODUCTION
Safety rules - General maintenance safety
General maintenance safety
Keep the area used for servicing the machine clean and dry. Clean up spilled fluids.
Service the machine on a firm, level surface.
Install guards and shields after you service the machine.
Close all access doors and install all panels after servicing the machine.
Do not attempt to clean, lubricate, clear obstructions, or make adjustments to the machine while it is in motion or while
the engine is running.
Always make sure that working area is clear of tools, parts, other persons and pets before you start operating the
machine.
Unsupported hydraulic cylinders can lose pressure and drop the equipment, causing a crushing hazard. Do not leave
equipment in a raised position while parked or during service, unless the equipment is securely supported.
Jack or lift the machine only at jack or lift points indicated in this manual.
Incorrect towing procedures can cause accidents. When you tow a disabled machine follow the procedure in this
manual. Use only rigid tow bars.
Stop the engine, remove the key, and relieve pressure before you connect or disconnect fluid lines.
Stop the engine and remove the key before you connect or disconnect electrical connections.
Scalding can result from incorrect removal of coolant caps. Cooling systems operate under pressure. Hot coolant can
spray out if you remove a cap while the system is hot. Allow the system to cool before you remove the cap. When
you remove the cap, turn it slowly to allow pressure to escape before you completely remove the cap.
Replace damaged or worn tubes, hoses, electrical wiring, etc.
The engine, transmission, exhaust components, and hydraulic lines may become hot during operation. Take care
when you service such components. Allow surfaces to cool before you handle or disconnect hot components. Wear
protective equipment when appropriate.
When welding, follow the instructions in the manual. Always disconnect the battery before you weld on the machine.
Always wash your hands after you handle battery components.
51537962 23/10/2018
5

12. SERVICE MANUAL
Engine
Magnum™ 180 PST TIER 4B [ZJRH04001 - ]
Magnum™ 200 PST TIER 4B [ZJRH04001 - ]
Magnum™ 220 PST TIER 4B [ZJRH04001 - ]
51537962 23/10/2018
10

13. Contents
Engine - 10
[10.001] Engine and crankcase ............................................................... 10.1
[10.216] Fuel tanks ............................................................................ 10.2
[10.218] Fuel injection system................................................................. 10.3
[10.202] Air cleaners and lines ................................................................ 10.4
[10.500] Selective Catalytic Reduction (SCR) exhaust treatment ............................. 10.5
[10.400] Engine cooling system ............................................................... 10.6
[10.414] Fan and drive ........................................................................ 10.7
[10.310] Aftercooler............................................................................ 10.8
[10.304] Engine lubrication system............................................................ 10.9
51537962 23/10/2018
10

14. Engine - Engine and crankcase
Engine - Remove
Prior operation:
Battery - Disconnect (55.302)
Prior operation:
Air intake lines Air scoop - Remove (10.202)
Prior operation:
Engine cooling system - Remove (10.400)
Prior operation:
Air conditioning - Recover - Refrigerant (50.200)
1. Disconnect the air sensor connector (1) and the
crankcase vent hose (2) from the air cleaner outlet
tube.
RAIL13TR01577AA 1
2. Disengage the clamp and remove the air cleaner outlet
hose (1) from the turbocharger.
RAIL13TR01582AA 2
3. Disengage the clamp at the air cleaner and remove the
air outlet tube.
RAIL13TR01583AA 3
51537962 23/10/2018
10.1 [10.001] / 3

15. Engine - Engine and crankcase
4. Remove the air cleaner mounting bolts (1) from each
side of the air cleaner bracket (left side shown).
RAIL13TR01585AA 4
5. Remove the air cleaner along with the mounting
bracket.
RAIL13TR01587AA 5
6. Disconnect the Diesel Exhaust Fluid (DEF)/AdBlue®
line (1), the coolant supply and return lines (2) and
the electrical connector (3) from the dosing module.
Squeeze the tabs together and lift the hose straight off
of the fitting.
RAIL13TR01586AA 6
51537962 23/10/2018
10.1 [10.001] / 4

16. Engine - Engine and crankcase
7. Disengage the clamp (1) from the input side of the
Diesel Exhaust Catalyst (DOC).
RAIL13TR01589AA 7
8. Disengage the clamp (1) from the output side of the
DOC.
RAIL13TR01590AA 8
9. Using proper lifting equipment, secure a strap to the
lifting bracket on the DOC.
RAIL13TR01592AA 9
51537962 23/10/2018
10.1 [10.001] / 5

17. Engine - Engine and crankcase
10. With tension on the lifting strap, remove the mounting
bracket bolts (1) for the DOC from both sides of the
bracket (left hand side is shown).
RAIL13TR01593AA 10
11. Raise the DOC and remove it from the tractor.
RAIL13TR01596AA 11
12. Remove the four mounting bolts (1) for the window
step. Remove the step.
RAIL13TR01594AA 12
51537962 23/10/2018
10.1 [10.001] / 6

18. Engine - Engine and crankcase
13. Cut the tie straps on the DEF/AdBlue® system har-
ness. Disconnect the two harness connectors (1).
RAIL13TR01597AA 13
14. Disconnect the 12 V auxiliary connector (1) and the
inlet fuel line from the fuel separator (2).
RAIL13TR01603AA 14
15. Disconnect the two connectors (1) for the front axle
harness.
RAIL13TR01625AA 15
51537962 23/10/2018
10.1 [10.001] / 7

19. Engine - Engine and crankcase
16. Remove the cab trim panels from both sides of the
cab, (right hand side shown).
RAIL13TR01611AA 16
17. Disconnect and cap the high and low pressure air con-
ditioning lines (1) located under the front of the cab.
RAIL13TR01599AA 17
18. Remove the cover plate from the driveshaft (left hand
side shown).
RAIL13TR01600AA 18
51537962 23/10/2018
10.1 [10.001] / 8

20. Engine - Engine and crankcase
19. Remove the bolts (1) for the mounting bracket for the
driveshaft cover plate. Disconnect the driveshaft from
the engine.
RAIL13TR01602AA 19
20. Remove the bolts (1) for the mounting bracket for the
air cleaner/DOC from the hood support bracket.
21. Remove the mounting bolts (left hand side shown)
which secure the hood support bracket to front frame
and remove the bracket. Repeat for right hand side.
RAIL13TR01608AA 20
22. Remove the air cleaner/DOC bracket.
RAIL13TR01609AA 21
51537962 23/10/2018
10.1 [10.001] / 9

21. Engine - Engine and crankcase
23. Disconnect the starter positive (1) and ground (2) ca-
bles.
24. Disconnect the chassis to engine harness connector
(3).
RAIL13TR01613AA 22
25. Disconnect the two hydraulic oil cooler lines (1). Cap
or plug all fittings and lines.
RAIL13TR01615AA 23
26. Disconnect the two coolant hoses (1).
RAIL13TR01616AA 24
51537962 23/10/2018
10.1 [10.001] / 10

22. Engine - Engine and crankcase
27. Disconnect the vacuum line (1) from the air intake col-
lector elbow.
RAIL13TR01624AA 25
28. Disengage the P-clamp for the vacuum line from the
fly wheel housing.
RAIL13TR01621AA 26
29. Attach appropriate lifting equipment to the front and
rear engine lifting brackets.
RAIL13TR01622AA 27
51537962 23/10/2018
10.1 [10.001] / 11

23. Engine - Engine and crankcase
30. Remove the two bolts (1) from the isolation clamp for
the front engine mount (right hand side shown).
RAIL13TR01626AA 28
31. Raise the engine from the frame. Check that all har-
nesses and hoses are disconnected. Remove the en-
gine from the frame.
32. Inspect the rear engine mounts for damage and/or
wear. Replace as necessary.
RCPH07CCH166AAB 29
33. Inspect the front engine support (1) and isolation
mount (2) for damage/and or wear. Replace as nec-
essary.
RCPH07CCH040BAB 30
34. Refer to the engine repair manual for information on
supporting the engine during repair.
Next operation:
51537962 23/10/2018
10.1 [10.001] / 12

24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

25. Engine - Engine and crankcase
Engine - Install
Prior operation:
Engine - Remove (10.001)
NOTICE: Check that all fittings are clean and free of foreign matter during assembly. Use new O-rings and lubricate
them with petroleum jelly prior to installation.
1. Properly support the engine and lower the engine into
the front frame.
RAIL13TR01627AA 1
2. Retain tension on the lifting equipment to align the front
isolation mount clamping bolts. Install the clamp and
bolts. Remove the tension on the lifting equipment.
3. Torque the engine mounting bolts to 59 – 106 N·m (44
– 78 lb ft).
4. Remove the lifting equipment.
RAIL13TR01626AA 2
5. Install the P-clamp (1) for the vacuum line on the fly-
wheel housing.
RAIL13TR01621AA 3
51537962 23/10/2018
10.1 [10.001] / 14

26. Engine - Engine and crankcase
6. Connect the vacuum line (1) for the air intake collector
elbow.
RAIL13TR01620AA 4
7. Connect the two coolant lines (1)
RAIL13TR01616AA 5
8. Connect the two hydraulic oil cooler lines (1) using new
O-rings.
RAIL13TR01615AA 6
51537962 23/10/2018
10.1 [10.001] / 15

27. Engine - Engine and crankcase
9. Connect the positive starter cable (1) and the ground
cable (2). Reconnect the chassis to engine harness
connector (3).
RAIL13TR01613AA 7
10. Install the hood support brackets (1) and secure the
brackets to the front frame using the bolts previously
removed.
11. Torque the bolts to 125 – 150 N·m (92 – 111 lb ft).
12. Reinstall the mounting bracket for the air cleaner/
Diesel Oxidation Catalyst (DOC). Secure the bracket
to the hood support bracket with the bolts (2) previ-
ously removed.
RAIL13TR01608AA 8
13. Align the yolk for the driveshaft with the flywheel adap-
tor plate, and install the bolts (1).
14. Torque the 101 – 113 N·m (75 – 83 lb ft).
15. Reinstall the mounting bracket (2) for the driveshaft
cover plate, and secure with the bolts previously re-
moved.
RAIL13TR01602AA 9
51537962 23/10/2018
10.1 [10.001] / 16