Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
385C L MH EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 385C L MH EXCAVATOR WAW
Configuration: 385C Material Handler WAW00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02536739
Fuel Priming Pump - Remove and Install
SMCS - 1258-010
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Turn the fuel supply to the “OFF” position.
1/3
385C Material Handler WAW00001-UP (MACHINE) POWERED BY C-18 Engine(S...
2020/10/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01049296
2. Remove bolts (2). Remove fuel priming pump assembly (1) from fuel filter base (4).
3. Remove gasket (3) from the fuel priming pump assembly and the fuel filter base.
Installation Procedure
NOTICE
2/3
2020/10/3

1. Position gasket (3) on fuel filter base (4).
2. Position fuel priming pump assembly (1) on the fuel filter base and install bolts (2).
3. Turn the fuel supply to the “ON” position.
4. Remove the air from the system. Refer to Testing and Adjusting, "Fuel System - Prime".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 3 09:18:02 UTC+0800 2020
3/3
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02213801
Fuel Filter Base - Remove
SMCS - 1262-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
NOTICE
containing fluids.
Cat products.
NOTICE
1/2
2020/10/3

2. Disconnect hose assembly (1) and hose assembly (3) from fuel filter base (4).
3. Use Tooling (A) to remove fuel filter (5) from fuel filter base (4).
4. Remove bolts (2). Remove fuel filter base (4).
Sat Oct 3 09:18:59 UTC+0800 2020
2/2
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02208021
Fuel Filter Base - Install
SMCS - 1262-012
NOTICE
1/2
2020/10/3

1. Position fuel filter base (4) on the engine.
2. Install bolts (2).
3. Install fuel filter (5) on the fuel filter base.
4. Connect hose assembly (1) and hose assembly (3) to the fuel filter base.
Sat Oct 3 09:19:56 UTC+0800 2020
2/2
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02208032
Fuel Transfer Pump - Remove
SMCS - 1256-011
Removal Procedure
NOTICE
containing fluids.
Cat products.
NOTICE
1/2
2020/10/3

2. Disconnect hose assembly (2) and hose assembly (3) from the fuel transfer pump.
3. Remove bolts (4).
4. Remove fuel transfer pump (1) and the O-ring seal from the adapter.
Sat Oct 3 09:20:52 UTC+0800 2020
2/2
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02208052
Fuel Transfer Pump - Install
SMCS - 1256-012
NOTICE
1/2
2020/10/3

1. Install the O-ring seal on fuel transfer pump (1). Lubricate the O-ring seal with clean engine
oil.
2. Position fuel transfer pump (1) in the adapter. Install bolts (4).
3. Connect hose assembly (2) and hose assembly (3) to the fuel transfer pump.
Sat Oct 3 09:21:49 UTC+0800 2020
2/2
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04164632
Electronic Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
A 5F-4764 Pry Bar 1
Start By:
A. Remove the rocker arms and the rocker arm shaft. Refer to Disassembly and Assembly,
"Rocker Arm and Shaft - Remove".
NOTICE
1/3
2020/10/3

1. Disconnect harness assembly (1) .
2. Remove bridge assemblies (3) .
NOTICE
Do not reuse the injector hold down bolts. New injector hold down
bolts must be used.
NOTICE
If the injector hold down bolt is loose during the removal procedure,
inspect the injector bore for wear and debris. Replace the clamp and
spacer.
3. Remove bolt (4) , spacer (5) , and clamp (6) . Discard bolt (4) .
4. Place an identification mark on electronic unit injectors (2) for installation purposes. Each
electronic unit injector must be reinstalled in the original location in the cylinder head.
2/3
2020/10/3

5. Use Tooling (A) to pry beneath the base and free electronic unit injector (2) .
6. Remove electronic unit injector (2) from the cylinder head.
Sat Oct 3 09:22:46 UTC+0800 2020
3/3
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07372365
Electronic Unit Injector - Install
SMCS - 1290-012
Table 1
Required Tools
B 8T-2998 Lubricant 1
C
1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle 1
4C-4057
Tube
7.9 mm (0.31 inch) OD
1
D 4C-5552 Large Bore Brush 1
E 4C-6774 Vacuum Gun Kit 1
F 8T-7765 Surface Reconditioning Pad 1
NOTICE
1/3
2020/10/3

1. Use Tooling (C) to remove the fuel and oil from the cylinder. Evacuate as much fuel and oil
as possible from the cylinder before installing the electronic unit injector. Several
evacuations may be necessary.
2. Use Tooling (D) to clean the carbon deposit from the inside the electronic unit injector
sleeve. Tooling (E) is available to clean loose material from the bore of the electronic unit
injector sleeve and the cylinder.
3. Use Tooling (F) to clean the carbon from the seat area that is inside the electronic unit
injector sleeve.
4. Install the O-ring seals on the electronic unit injector. Lubricate the top two O-ring seals
with a 50/50 mixture of clean engine oil and Tooling (B).
NOTICE
When an electronic unit injector is replaced, the new electronic
injector code must be programmed into the engine's personality
module software by using the calibration menu on the Electronic
Service Tool. If the new electronic injector code is not entered, the
characteristics of the previous electronic unit injector is assumed.
If it is not possible to immediately reprogram the electronic injector
code into the personality module software, the engine will not be
severely harmed. The new electronic injector code should be
reprogrammed as quickly as possible in order to optimize engine
performance.
5. Install electronic unit injector (2) into the original location in the cylinder head.
2/3
2020/10/3

6. Install spacer (5), clamp (6), and bolt (4). Tighten the bolt to a torque of 55 ± 10 N·m
(41 ± 7 lb ft).
7. Install bridge assemblies (3) in the respective locations.
Note: Be sure that the larger hole on the bridge assembly is installed towards the rocker.
8. Connect harness assembly (1) on electronic unit injector (2). Tighten the nuts to a torque of
2.5 ± 0.25 N·m (22 ± 2 lb in).
End By:
a. Install the rocker arms and the rocker arm shaft. Refer to Disassembly and Assembly,
"Rocker Arm and Shaft - Install".
Sat Oct 3 09:23:43 UTC+0800 2020
3/3
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i06729616
Electronic Unit Injector Sleeve - Remove
SMCS - 1713-011
Removal Procedure
Table 1
Required Tools
A 9U-6891 Injector Tool Group 1
Start By:
a. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
1/2
2020/10/3

2. Install Tooling (A) in electronic unit injector sleeve (1).
3. Tighten the nut on Tooling (A) until the electronic unit injector sleeve is pulled free of the
cylinder head.
4. Remove O-ring seals (2) and O-ring seal (3) from electronic unit injector sleeve (1).
Sat Oct 3 09:24:40 UTC+0800 2020
2/2
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i06745960
Electronic Unit Injector Sleeve - Install
SMCS - 1713-012
Table 1
Required Tools
A 9U-6891 Injector Tool Group 1
B
9U-6862 Tapered Brush 1
9U-6863 Small Bore Brush 1
9U-7244 End Brush 1
9U-7237 Brush Extension 1
4C-5552 Large Bore Brush 1
C Loctite 620 Retaining Compound 1
NOTICE
1. Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
1/3
2020/10/3

NOTICE
Ensure that the electronic unit injector sleeve and the cylinder head
bore are completely free of oil, dirt, and sealant debris.
2. Install new O-ring seals (2) and O-ring seal (3) on electronic unit injector sleeve (1).
3. Apply Tooling (C) to the contact surface of electronic unit injector sleeve (1) on the surface
that is Marked "X".
Note: Do not apply Tooling (C) to the cylinder head surfaces. Apply Tooling (C) on the
electronic unit injector sleeve only.
4. Lubricate O-ring seals (2) with clean engine oil.
2/3
2020/10/3

5. Install electronic unit injector sleeve (1) on Tooling (A). Position the electronic unit injector
sleeve in the cylinder head. Use care not to damage the O-ring seals on the electronic unit
injector sleeve. Use Tooling (A) and a hammer to install the electronic unit injector sleeve
in the cylinder head.
NOTICE
Ensure that the electronic unit injector sleeve is properly seated in the
cylinder head. The Tooling will "RING" when the electronic unit
injector sleeve is fully seated in the bore of the cylinder head.
6. Remove Tooling (A). Remove excess Tooling (C).
7. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Change".
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
Sat Oct 3 09:25:37 UTC+0800 2020
3/3
2020/10/3

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02208257
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
containing fluids.
Cat products.
NOTICE
1. Drain the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
1/2
2020/10/3

2. Disconnect tube assembly (3) and tube assembly (6).
3. Disconnect tube assembly (2) and tube assembly (4).
4. Attach a suitable lifting device to turbocharger (1). The weight of the turbocharger is
approximately 34 kg (75 lb).
5. Remove locknuts (5). Remove turbocharger (1) and the gasket from the exhaust manifold.
Sat Oct 3 09:26:33 UTC+0800 2020
2/2
2020/10/3

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04391596
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
1/2
2020/10/3

Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual Instant Download.pdf (20)

More from qianxu35543635

More from qianxu35543635 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual Instant Download.pdf