Birkosit Product Safety Data Sheets, May 2011 version
1. A.I. Schulze
Chemotechnische Fabrik e.K.
Alleinhersteller und Vertrieb ®
BIRKOSIT Dichtungskitt
A.I. Schulze Chemotechnische Fabrik e.K., Theodor-Körner-Str. 3 A, 02826 GÖRLITZ - GERMANY
®
BIRKOSIT Dichtungskitt
for maximum temperature and pressure resistance
®
BIRKOSIT BIRKOSIT Dichtungskitt is a single-component, paste luting agent/sealing material for
Description industrial use wherever conditions of temperature combined with pressure on smooth,
plane sealing surfaces (butt joints) make extreme demands on the quality of the
sealing compound. This applies, in particular, to the sealing of metallic joints in:
steam and gas turbines, compressors, generators, expanders, pumps, flange
joints, etc.
®
BIRKOSIT BIRKOSIT Dichtungskitt withstands hot steam and air, hot and cold water, light fuel
Temperature oils and lubricants, as well as crude oil and natural gas at temperatures of
resistance up to 900 °C.
BIRKOSIT The adhesion on sealing surfaces and butt joints is so high that a one hundred
Pressure percent seal is guaranteed even for pressures up to 250 bar.
resistance The pressure resistance for flanges without sealing rings is guaranteed up to 450 bar,
and even up to 550 bar for screw joints.
BIRKOSIT When used in accordance with instructions and with regular servicing as required for
Service life steam and gas turbines as well as for the application areas stated above, we
guarantee a service life for use on machined sealing surfaces (butt joints) of 10 years.
®
BIRKOSIT BIRKOSIT Dichtungskitt is suitable for sealing all surface sizes. The surface quality of
Fields of the sealing surfaces complies with milled/scraped surfaces with a finishing accuracy
Application of Ra = 0.8 µm to 1.2 µm.
®
Sealing surface damage of ≤ 0.2 mm is compensated with BIRKOSIT Dichtungskitt .
To compensate individual points of severe damage of ≥ 0.2 mm to 1.0 mm, we
®
recommend our additional products BIRKOSIT Dichtungskitt Filling1000 and
®
BIRKOSIT Dichtungskitt Filling2000.
®
BIRKOSIT Apply the BIRKOSIT Dichtungskitt to the dry sealing surfaces with a brush or putty knife.
Application The layer thickness to be applied is 0.2 mm to 0.3 mm. The product can be
subjected to workloads immediately! It does not cure, will not change its
consistency even after several hours, and remains flexible and elastic.
It is therefore also suitable for butt joint machining.
The colour is reddish brown. Heating the tin to room temperature or adding a tenth part
of standard linseed oil varnish will improve the brushability.
®
BIRKOSIT Packed in 1 kg tins. If stored correctly, BIRKOSIT Dichtungskitt has a storage life
Storage of 5 years in the tin. Its properties are stable and it is flexible in use.
Close the tin properly if only a part of the contents is going to be used.
Product data sheet as at 01/05/2011. Current download version at www.a-i-schulze.com.
A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0
Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20
Company address: Account number 4 562 135 800 email: info@a-i-schulze.com
Theodor-Körner-Str. 3 A IBAN DE33 8559 1000 4562 1358 00 Web: www.birkosit-dichtungskitt.com
02826 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden
GERMANY VAT ref. no. DE812553785 HRA 7441
2. A.I. Schulze
Chemotechnische Fabrik e.K.
Alleinhersteller und Vertrieb®
BIRKOSIT Dichtungskitt
A.I. Schulze Chemotechnische Fabrik e.K., Theodor-Körner-Str. 3 A, 02826 GÖRLITZ - GERMANY
®
BIRKOSIT Dichtungskitt
for maximum temperature and pressure resistance
In addition to the product information in our product documents, the 2011 product specification sheet and
the safety data sheet as per 91/155/EEC, we confirm the following additions for our General Agency:
Quality management
To ensure the high quality of our products and services and to continually improve our organisation, we
regularly perform in-house audits to make sure that our company meets the requirements of the DIN EN
ISO 9001 quality standard to which our company is certified.
®
Service life of the product BIRKOSIT Dichtungskitt
BIRKOSIT When used in accordance with instructions and with regular servicing as
Service required for steam and gas turbines, we guarantee a service life of 10 years
life for use on machined sealing surfaces (butt joints) with a finishing accuracy of
Ra = 0.8 µm to 1.2 µm. For high-pressure turbines (H), medium-pressure turbines (M)
and low-pressure turbines (L) we guarantee that the product will withstand hot steam
and hot air, hot and cold water, light fuel oils and lubricants as well as crude oil and
natural gas up to 900°C and withstand pressure up to 250 bar.
BIRKOSIT The following information on the tin label of our products ensures reliable
Service life data service life monitoring:
on the tin Filling date, unopened useable until, service life after opening, opened on
(the last detail is to be entered by qualified staff working for the customer)
BIRKOSIT Unopened tin
Service life data If stored correctly, we guarantee a service life of the product in the tin of 5 years.
in storage
Opened tins
If the tins are resealed correctly after partial use, we guarantee a service life of the
product of 3 years.
BIRKOSIT After removal from the tin, we guarantee a product service life of 10 years for the
Product use product in use.
Görlitz, 01.05.2011
A.I. Schulze Chemotechnische Fabrik e.K.
Company Management
Dieter Bartkowiak
A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0
Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20
Company address: Account number 4 562 135 800 email: info@a-i-schulze.com
Theodor-Körner-Str. 3 A IBAN DE33 8559 1000 4562 1358 00 Web: www.birkosit-dichtungskitt.com
02826 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden
GERMANY VAT ref. no. DE812553785 HRA 7441
3. A.I. Schulze
Chemotechnische Fabrik e.K.
Alleinhersteller und Vertrieb®
BIRKOSIT Dichtungskitt
A.I. Schulze Chemotechnische Fabrik e.K., Theodor-Körner-Str. 3 A, 02826 GÖRLITZ - GERMANY
®
BIRKOSIT Dichtungskitt
for maximum temperature and pressure stability
Safety data sheet conforming to 91/155/EEC (UPDATE: 93/112/EC)
Amended on 93/112/EC and 2001/58/EC
Date: 01.05.2011 Page 1 of 5 replaces all earlier safety data sheets
The latest version may be found on our website: www.birkosit-dichtungskitt.com
The information provided here is based upon the current level of our knowledge and experience. The
safety data sheet describes our product in terms of safety requirements and represents no warranty of
properties. It is the consignee’s own responsibility to observe the existing laws and regulations.
PNUMBER: 51001
®
BIRKOSIT Registered trade name: BIRKOSIT Dichtungskitt
1. Product and Application: For sealing metallic joints
trade name Company: A.I. Schulze Chemotechnische Fabrik e.K.
Address: Theodor-Körner-Str. 3 A, 02826 GÖRLITZ, GERMANY
Contact: Tel. +49 3581 75005-0 Fax +49 3581 75005-20
Emergency telephone number: Tel. +49 3581 75005-10
email: management@a-i-schulze.com
BIRKOSIT Formulation based upon a modified organic resin and paraffin mineral oil.
2. Composition The formulation contains both inorganic and organic additives.
Information on 2.1 The product contains the following relevant components.
ingredients 2.2 Characterisation of relevant contents according to 2.1:
CAS No.: Name: EEC No.: Index No.: Symbols: Risk phrases:
8001-26-1 Boiled Linseed oil - - - -
3
1309-37-1 Synthetic iron oxide - - - 3 mg/m
BIRKOSIT Handling the product does not involve any special risks as long as it is
3. Possible used in compliance with the standard regulations for industrial hygiene.
hazards If the usual regulations for waste disposal are observed (see point 13) this
product does not present any significant danger for the environment.
A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0
Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20
Company address: Account number 4 562 135 800 email: info@a-i-schulze.com
Theodor-Körner-Str. 3 A IBAN DE33 8559 1000 4562 1358 00 Web: www.birkosit-dichtungskitt.com
02826 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden
GERMANY VAT ref. no. DE812553785 HRA 7441
4. A.I. Schulze
Chemotechnische Fabrik e.K.
Alleinhersteller und Vertrieb®
BIRKOSIT Dichtungskitt
A.I. Schulze Chemotechnische Fabrik e.K., Theodor-Körner-Str. 3 A, 02826 GÖRLITZ - GERMANY
®
BIRKOSIT Dichtungskitt
for maximum temperature and pressure stability
®
Registered trade name: BIRKOSIT Dichtungskitt
Page 2 of 5
BIRKOSIT 4.1 General comments: Inhalation is not a primary mode of exposure.
4. First-aid measures The measures provided are of a general nature.
4.2 In case of eye contact: Hold eyelid wide open and thoroughly and
continuously rinse out with water. Seek medical attention if irritation persists.
4.3 In case of skin contact: As far as possible remove the product using a clean
soft cloth and wash affected areas of the skin thoroughly with water.
4.4 In case of ingestion: Arrange medical treatment as necessary for affected
persons.
4.5 In case of inhalation: Take those affected into fresh air. Seek medical
attention in case of nausea.
4.6 Instruction to the doctor: No special treatments are known. Just treat any
symptoms.
BIRKOSIT Suitable extinguishing agents: CO2 powder and foam extinguishers, water spray
5. Firefighting jet. Unsuitable extinguishing agents from safety reasons: water in full jet.
measures Particular hazards due to the product or due to its combustion products:
As a rule no particular hazards are to be anticipated since the product is
exclusively sold in small containers. The product is combustible. With
incineration or thermal decomposition of the product harmful and irritating gases
and vapours are released.
Special protective equipment and/or measures for firefighting:
The measures specified below are based exclusively upon large fires. Cool off
the fire-damaged containers with a water spray jet. In case of fire employ
self-contained breathing apparatus and don protective clothing. As far as
possible collect and dispose of extinguishing water.
BIRKOSIT Pick up undamaged small containers (cans, tubes, etc.). If larger amounts
6. Measures in of product have been spilled due to damaged containers, don protective
cases of unintended clothing (See point 8.2.1) and stop further product escaping. Otherwise,
release clear up spillages/leakages with a dry absorbent agent (sand, soil, general-
purpose binder, etc.) and dispose of them as specified in point 13. Clean the
floor thoroughly.
A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0
Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20
Company address: Account number 4 562 135 800 email: info@a-i-schulze.com
Theodor-Körner-Str. 3 A IBAN DE33 8559 1000 4562 1358 00 Web: www.birkosit-dichtungskitt.com
02826 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden
GERMANY VAT ref. no. DE812553785 HRA 7441
5. A.I. Schulze
Chemotechnische Fabrik e.K.
Alleinhersteller und Vertrieb®
BIRKOSIT Dichtungskitt
A.I. Schulze Chemotechnische Fabrik e.K., Theodor-Körner-Str. 3 A, 02826 GÖRLITZ - GERMANY
®
BIRKOSIT Dichtungskitt
for maximum temperature and pressure stability
®
Registered trade name: BIRKOSIT Dichtungskitt
Page 3 of 5
BIRKOSIT 7.1 Handling: Process product only in well-ventilated wor premises. Do not
7. Handling and smoke when processing the product. Follow the application instructions exactly.
storage 7.2 Storage: The following measures are based upon storing large quantities
of the product. Store the product dry and cool in the sealed original containers.
Take appropriate measures to prevent the product from entering the sewage or
water circulation systems in case of spillage. Do not store the product near to
foodstuffs, beverages or animal feeds, and ensure it is inaccessible to children.
Heed the storage class when storing large amounts or storing in bulk.
Storage class: 11, Storage class concept of the VCI (1991) (German Chemical
Industries Association)
BIRKOSIT 8.1 Design of technical systems/plants:
8. Exposure limits No additional measures are required beyond those in point 7.
and personal safety 8.2 Components having workplace-related limiting values:
equipment The current product contains no components having workplace-related limiting
values.
8.2.1 Work hygiene and personal protective wear:
Do not eat, drink or smoke in the workplace. Avoid sustained/repeated contact
with the product. Change soiled workwear and clean thoroughly before re-use.
Do not rub your eyes with dirty hands. Wash hands after working and before
going to the toilet.
Respiratory protection: Not necessary
Eye protection: Safety goggles with closed sides (not mandatory, but
recommended)
Hand protection: Protective gloves made from plastics (not mandatory,but
recommended)
Body protection: Workwear
A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0
Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20
Company address: Account number 4 562 135 800 email: info@a-i-schulze.com
Theodor-Körner-Str. 3 A IBAN DE33 8559 1000 4562 1358 00 Web: www.birkosit-dichtungskitt.com
02826 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden
GERMANY VAT ref. no. DE812553785 HRA 7441
6. A.I. Schulze
Chemotechnische Fabrik e.K.
Alleinhersteller und Vertrieb®
BIRKOSIT Dichtungskitt
A.I. Schulze Chemotechnische Fabrik e.K., Theodor-Körner-Str. 3 A, 02826 GÖRLITZ - GERMANY
®
BIRKOSIT Dichtungskitt
for maximum temperature and pressure stability
®
Registered trade name: BIRKOSIT Dichtungskitt
Page 4 of 5
BIRKOSIT 9.1 Form: viscous at 20 °C
9. Physico- chemical Colour: coloured
properties Odour: charecteristic
3
9.2 Density: (25 °C) ~ 1.1 g/cm
Bulk density: (20 °C) not applicable
Vapour pressure: (20 °C) < 1 hPa
Viscosity: (25 °C) no data
Solubility in water: (20 °C) practically insoluble
Lipophilicity: partially miscible with common organic solvents
pH value: not applicable
Flash point: no data
Ignition temperature: no data
Explosion hazard: none
Partition coefficient n-octanol/water, log POW: not applicable
BIRKOSIT 10.1 Conditions to avoid: the product is stable at room temperature.
10. Stability and 10.2 Materials to avoid: strong oxidants
reactivity 10.3 Hazardous decomposition products: in the case of combustion/thermal
decomposition of the product carbon monoxide, carbon dioxide and inorganic
oxides are formed.
BIRKOSIT Handling the product does not involve any special risks as long as it is
11. Toxicology data used in compliance with the standard regulations for industrial hygiene.
LD.LC50 values relevant to classification
Oral LD50 4986 mg/kg (rat)
BIRKOSIT Do not allow product to escape into environment. Decant and treat
12. Ecological the contaminated waste water before it is discharged into the sewage system.
information
Water hazard class WK1 (slightly hazardous to water)
(in accordance with VwVwS published 17.05.1999, derived from the now lapsed
WK 0)
A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0
Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20
Company address: Account number 4 562 135 800 email: info@a-i-schulze.com
Theodor-Körner-Str. 3 A IBAN DE33 8559 1000 4562 1358 00 Web: www.birkosit-dichtungskitt.com
02826 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden
GERMANY VAT ref. no. DE812553785 HRA 7441
7. A.I. Schulze
Chemotechnische Fabrik e.K.
Alleinhersteller und Vertrieb®
BIRKOSIT Dichtungskitt
A.I. Schulze Chemotechnische Fabrik e.K., Theodor-Körner-Str. 3 A, 02826 GÖRLITZ - GERMANY
®
BIRKOSIT Dichtungskitt
for maximum temperature and pressure stability
®
Registered trade name: BIRKOSIT Dichtungskitt
Page 5 of 5
BIRKOSIT Empty containers fully (cans, tubes, etc.) and dispose of them in the standard
13. Disposal recycling process. End users can suitably dispose of small amounts of product
considerations residues in the original packing by handing them in to their local hazardous
waste plant (or mobile hazardous materials collection vehicles). Professional
users must dispose of the product in accordance with the specified waste code
number.
Waste code no.: 559 07 Lute and mastic compounds, not fully hardened
BIRKOSIT IMG Code: - UN No.: - ICAO/IATA: -
14. Transport GGVS/GGVE: - RID/ADR: - ADNR: -
information KEMLER ZAHL: - MFAG: - EMS: -
TREMCARD: - IATA page: - VERP Group: -
GEF.-ZETTEL: - MARINE POL.: - IMDG Label: - SKZ No: -
There are no particular precautions to observe.
BIRKOSIT At the time of creating the data sheet there is no hazardous substance
15. Regulations within the meaning of the hazardous substances directive or the relevant
EC Guidelines in their latest valid versions (67/548/EEC and 88/379/EEC)
BIRKOSIT Lit. 1: Derivation from the safety data sheets of the individual components.
16. Other information The following items of the data sheet have been amended compared with the
safety data sheet dated 01.01.2010.
Point 1, 6 and 9
A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0
Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20
Company address: Account number 4 562 135 800 email: info@a-i-schulze.com
Theodor-Körner-Str. 3 A IBAN DE33 8559 1000 4562 1358 00 Web: www.birkosit-dichtungskitt.com
02826 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden
GERMANY VAT ref. no. DE812553785 HRA 7441