This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336F and 336F L Excavator (Prefix YFD) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include bolts, nuts, washers, threaded rods, eyebolts, various drivers, pullers, pliers and other tools. Detailed illustrations are provided to show each component and step in the disassembly process. Safety notices are included to warn of potential spring forces and contain fluids properly.
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, various plugs and seals, springs, relief valves, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...dujdkksmdm
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, swashplate, and various seals and plates. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...8dskeddmdd
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include bolts, nuts, washers, threaded rods, eyebolts, various drivers, pullers, pliers and other tools. Detailed illustrations are provided to show each component and step in the disassembly process. Safety notices are included to warn of potential spring forces and contain fluids properly.
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, nuts and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...f8uesjdkdmdm
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, various plugs and seals, springs, relief valves, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Safety precautions are provided to release spring forces and contain fluids.
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include bolts, nuts, washers, threaded rods, eyebolts, various drivers, pullers, pliers and other tools. Detailed illustrations are provided to show each component and step in the disassembly process. Safety notices are included to warn of potential spring forces and contain fluids properly.
Fiat Kobelco SL30B Skid Steer Loader Service Repair Manual.pdfprmy389342
This document is the service manual for an SL30B skid steer loader. It provides safety precautions and instructions for operating and servicing the loader. Some key points:
- The manual outlines many safety rules for operating the loader safely, such as wearing protective equipment, not allowing passengers, and ensuring all equipment is lowered before servicing.
- It provides standard torque specifications for various types of hardware including decimal, metric, and hydraulic fittings to ensure correct tightening of components.
- The manual is organized into tabs covering general information, engines, fuel system, electrical systems, power train, hydraulics, and mounted equipment. Each tab contains an index of relevant sections.
- Sections provide instructions
Caterpillar Cat 336F and 336F L Excavator (Prefix YFD) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include bolts, nuts, washers, threaded rods, eyebolts, various drivers, pullers, pliers and other tools. Detailed illustrations are provided to show each component and step in the disassembly process. Safety notices are included to warn of potential spring forces and contain fluids properly.
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, various plugs and seals, springs, relief valves, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...dujdkksmdm
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, swashplate, and various seals and plates. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...8dskeddmdd
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include bolts, nuts, washers, threaded rods, eyebolts, various drivers, pullers, pliers and other tools. Detailed illustrations are provided to show each component and step in the disassembly process. Safety notices are included to warn of potential spring forces and contain fluids properly.
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, nuts and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...f8uesjdkdmdm
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, various plugs and seals, springs, relief valves, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Safety precautions are provided to release spring forces and contain fluids.
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include bolts, nuts, washers, threaded rods, eyebolts, various drivers, pullers, pliers and other tools. Detailed illustrations are provided to show each component and step in the disassembly process. Safety notices are included to warn of potential spring forces and contain fluids properly.
Fiat Kobelco SL30B Skid Steer Loader Service Repair Manual.pdfprmy389342
This document is the service manual for an SL30B skid steer loader. It provides safety precautions and instructions for operating and servicing the loader. Some key points:
- The manual outlines many safety rules for operating the loader safely, such as wearing protective equipment, not allowing passengers, and ensuring all equipment is lowered before servicing.
- It provides standard torque specifications for various types of hardware including decimal, metric, and hydraulic fittings to ensure correct tightening of components.
- The manual is organized into tabs covering general information, engines, fuel system, electrical systems, power train, hydraulics, and mounted equipment. Each tab contains an index of relevant sections.
- Sections provide instructions
Fiat Kobelco EX95W Mini Wheel Excavator Service Repair Manual.pdfprmy389342
This document provides safety precautions for operating an excavator. It advises reading the operator's manual carefully before starting or using the machine. Operators should be familiar with all safety signs and their meanings. Only authorized personnel should operate the machine. Personal protective equipment such as hard hats and safety glasses should always be worn. The operator's compartment and controls should be kept clean. Operators should not jump on or off the machine and should keep hands and feet inside the cab at all times. The machine should come to a complete stop before the operator exits. Height, width and weight limitations of the work site must be assessed. Underground utilities should be located and marked before digging.
Daewoo Doosan DE12TIS Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12TI Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12T Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12 Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfprmy389342
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, rear doors, covers, fasteners, and guards. The parts are organized with an index and diagram to allow technicians to easily find replacement parts.
Crown LP3020 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes overview diagrams of truck components, inspection and maintenance schedules, repair procedures, and part replacement instructions. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown LP3010 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes safety notes, inspection and maintenance schedules, repair and replacement procedures, and diagrams. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown GPC2000 Series Lift Truck Parts Catalogue Manual.pdfprmy389342
This document provides lubrication information for a parts manual. It lists the recommended lubricants and their specifications for various components of the product. Grease type 2 is recommended for bearings and grease type 2-P for ball bearings. Mobilex 00-200 is suitable for lower operating temperatures, while Mobilex 005-200 is recommended for higher temperatures.
Clark TMX12-25 Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages and outlining safe maintenance practices such as blocking the wheels, disconnecting batteries, and checking for fuel leaks before working.
2. Procedures for lifting parts of the forklift like the drive wheels or rear, including using blocks and jacks of adequate capacity.
3. Chain securing an upright carriage when raised and shipping tie-down instructions.
Clark EPX 16-20S Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages in the manual and on trucks to understand hazards.
2. Recommended safe maintenance practices such as properly ventilating work areas, using fire protection equipment, and disconnecting batteries before working on electrical systems.
3. Procedures for safely lifting, jacking, and blocking forklifts, including raising the drive wheels, upright, and entire truck, to access components for repair work.
Clark CMP 70 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 60 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 50 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar Cat D400E II EJECTOR TRUCK (Prefix APF) Service Repair Manual (AP...prmy389342
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety notices warn of potential injury from compressed springs and ensure cleanliness when handling engine parts.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. The pump is removed from the machine and various internal components are then dismantled. These components include pressure and flow compensator valves, springs, seals, pistons, barrels and housings. Detailed illustrations accompany each step to show how to access fasteners and position parts for removal or disassembly. Safety notices are also included regarding contained fluids and released spring forces during the process. The overall document provides a technical service manual excerpt on thoroughly disassembling a hydraulic pump assembly.
Fiat Kobelco EX95W Mini Wheel Excavator Service Repair Manual.pdfprmy389342
This document provides safety precautions for operating an excavator. It advises reading the operator's manual carefully before starting or using the machine. Operators should be familiar with all safety signs and their meanings. Only authorized personnel should operate the machine. Personal protective equipment such as hard hats and safety glasses should always be worn. The operator's compartment and controls should be kept clean. Operators should not jump on or off the machine and should keep hands and feet inside the cab at all times. The machine should come to a complete stop before the operator exits. Height, width and weight limitations of the work site must be assessed. Underground utilities should be located and marked before digging.
Daewoo Doosan DE12TIS Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12TI Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12T Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12 Diesel Engine Service Repair Manual.pdfprmy389342
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfprmy389342
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, rear doors, covers, fasteners, and guards. The parts are organized with an index and diagram to allow technicians to easily find replacement parts.
Crown LP3020 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes overview diagrams of truck components, inspection and maintenance schedules, repair procedures, and part replacement instructions. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown LP3010 Lift Truck Service Repair Manual.pdfprmy389342
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes safety notes, inspection and maintenance schedules, repair and replacement procedures, and diagrams. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown GPC2000 Series Lift Truck Parts Catalogue Manual.pdfprmy389342
This document provides lubrication information for a parts manual. It lists the recommended lubricants and their specifications for various components of the product. Grease type 2 is recommended for bearings and grease type 2-P for ball bearings. Mobilex 00-200 is suitable for lower operating temperatures, while Mobilex 005-200 is recommended for higher temperatures.
Clark TMX12-25 Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages and outlining safe maintenance practices such as blocking the wheels, disconnecting batteries, and checking for fuel leaks before working.
2. Procedures for lifting parts of the forklift like the drive wheels or rear, including using blocks and jacks of adequate capacity.
3. Chain securing an upright carriage when raised and shipping tie-down instructions.
Clark EPX 16-20S Forklift Service Repair Manual.pdfprmy389342
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages in the manual and on trucks to understand hazards.
2. Recommended safe maintenance practices such as properly ventilating work areas, using fire protection equipment, and disconnecting batteries before working on electrical systems.
3. Procedures for safely lifting, jacking, and blocking forklifts, including raising the drive wheels, upright, and entire truck, to access components for repair work.
Clark CMP 70 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 60 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 50 Forklift Service Repair Manual.pdfprmy389342
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar Cat D400E II EJECTOR TRUCK (Prefix APF) Service Repair Manual (AP...prmy389342
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety notices warn of potential injury from compressed springs and ensure cleanliness when handling engine parts.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. The pump is removed from the machine and various internal components are then dismantled. These components include pressure and flow compensator valves, springs, seals, pistons, barrels and housings. Detailed illustrations accompany each step to show how to access fasteners and position parts for removal or disassembly. Safety notices are also included regarding contained fluids and released spring forces during the process. The overall document provides a technical service manual excerpt on thoroughly disassembling a hydraulic pump assembly.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR DSW
Configuration: 336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR DSW
Configuration: 336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR DSW
Configuration: 336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336F & 336F L Excavators DSW00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/6/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...