Caterpillar Cat 306E Mini Hydraulic Excavator (Prefix FHL) Service Repair Manual (FHL00001 and up).pdf

Service Repair Manual
Models
306E Mini Hydraulic
Excavator

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 306E MINI HYD EXCAVATOR FHL
Configuration: 306E Mini Hydraulic Excavator FHL00001-UP (MACHINE) POWERED BY C2.6 Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242928
Camshaft and Valve Lifters - Remove and Install - C2.6
SMCS - 1209-010; 1210-010
S/N - CE21-UP
S/N - F8C1-UP
S/N - FHL1-UP
S/N - H1Y1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Magnets 8
B 390-1149 Driver 1
Start By:
a. Remove the rocker shaft and pushrods.
b. Remove the flywheel housing.
c. Remove the oil pan. (Only necessary if valve lifters will be removed.)
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
1/4
306E Mini Hydraulic Excavator FHL00001-UP (MACHINE) POWERED BY C2.6 En...
2020/1/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03190322
1. Ensure that Timing Marks (Y) on the idler gear and the camshaft gear are aligned. Refer to
illustration 1.
2. Use Tooling (A) to hold up the valve lifters (1) in order to remove the camshaft.
2/4
2020/1/30

NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
3. Remove bolts (3).
4. Carefully remove camshaft (2) from the cylinder block.
5. Remove Tooling (A). Use a suitable container to catch the valve lifters (1) as the valve
lifters (1) slide out the bottom of the cylinder block.
6. Remove the camshaft cover (4).
3/4
2020/1/30

Installation Procedure
1. Install camshaft (1) in the reverse order of removal.
a. Place camshaft cover (4) on Tooling (B).
b. Use Tooling (B) to install the camshaft cover (4).
c. Tighten bolts (3) to a torque of 24.0 ± 27.0 N·m (17.70 ± 19.91 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jan 30 23:07:55 UTC+0800 2020
4/4
2020/1/30

Shutdown SIS
Previous Screen
i05242932
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
A 1P-0510 Driver Group 1
B 8B-7551 Puller Assembly 1
C 8H-0663 Bearing Puller 1
Start By:
a. Remove the camshaft.
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3
2020/1/30

1. Use Tooling (A) in order to remove camshaft gear (1) from camshaft (2).
2. If necessary, apply heat to raise the temperature of the race (3) of the roller bearing to
remove.
3. Remove plate (5) from camshaft (2).
4. If necessary, remove the key (4) from the nose of camshaft (2).
1. Install camshaft gear (1) in the reverse order of removal.
2/3
2020/1/30

a. Use Tooling (B) and Tooling (C) in order to install camshaft gear (1) onto camshaft
(2).
b. Ensure that the camshaft gear and the key are clean and free from wear and damage.
Thu Jan 30 23:08:52 UTC+0800 2020
3/3
2020/1/30

Shutdown SIS
Previous Screen
i05242933
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Table 1
Required Tools
A - LOCTITE 38364 Flange Sealant 1
Values.
1. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the
proper draining and filling procedures.
2. Remove bolts (2) and remove oil pan (1).
1/2
2020/1/30

3. Remove Tooling (A) from oil pan (1) and cylinder block (3) surfaces.
1. Install oil pan (1) in the reverse order of removal.
a. Apply Tooling (A) to cylinder block (3) surface.
Thu Jan 30 23:09:49 UTC+0800 2020
2/2
2020/1/30

Shutdown SIS
Previous Screen
i05242938
Pistons and Connecting Rods - Remove and Install
SMCS - 1225-010
Removal Procedure
Start By:
a. Remove cylinder head.
b. Remove engine oil pan.
Values.
1. Rotate the crankshaft until the crank pin is at the bottom center position.
2. Remove bolts (2) and remove connecting rod cap (1).
1/5
2020/1/30

3. Carefully push piston (3) and the connecting rod from cylinder block (4) bore.
4. The connecting rod and the connecting rod cap should have an etched Number (X) on the
side. The number on the connecting rod and the connecting rod cap must match. Ensure that
the connecting rod and the connecting rod cap are marked for the correct location. If
necessary, make a temporary mark on the connecting rod and the connecting rod cap in
order to identify the cylinder number.
5. Remove piston (3) and connecting rod (5).
Table 1
Required Tools
A 1U-6684 Piston Ring Compressor 1
2/5
2020/1/30

1. Inspect piston (3) and connecting rod assembly (5).
2. Apply clean engine oil to the cylinder bore, to the piston rings, to the outer surface of the
piston and to the bearing shells.
Note: Install the bearing shells for the connecting rods dry when clearance checks are
performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the
correct procedure. Apply clean engine oil to the bearing shells for the connecting rods
during final assembly.
Note: Ensure that the piston and the connecting rod assembly are installed in the correct
cylinder.
3. Install Tooling (A) onto piston (3).
Note: Ensure that Tooling (A) is installed correctly and that piston (3) can easily slide from
the tool.
3/5
2020/1/30

4. Carefully push piston (3) and the connecting rod assembly into cylinder block (4) bore and
onto the crankshaft pin.
5. Install connecting rod cap (1) onto the connecting rod .
Note: Ensure that etched Number (X) on connecting rod cap (1) matches etched Number
(X) on the connecting rod. Ensure the correct orientation of the connecting rod cap. The
locating tab for the upper bearing shell and the lower bearing shell should be on the same
side.
Note: Do not reuse the old connecting rod bolts in order to secure the connecting rod cap.
6. For the C3.3B apply clean engine oil to bolt threads and install new bolts (2) to the
connecting rod. Tighten bolts (2) to a torque of 69 to 73 N·m (51 to 54 lb ft).
7. For the C2.6 apply clean engine oil to bolt threads and install new bolts (2) to the
connecting rod. Tighten bolts (2) to a torque of 45 ± 49 N·m (33 ± 36 lb ft).
8. Ensure that the installed connecting rod assembly has side play. Rotate the crankshaft in
order to ensure that there is no binding.
9. Repeat Step 1 through Step 8 in order to install the remaining pistons and connecting rods.
End By:
4/5
2020/1/30

a. Install engine oil pan.
b. Install cylinder head.
Thu Jan 30 23:10:45 UTC+0800 2020
5/5
2020/1/30

Shutdown SIS
Previous Screen
i05845101
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
A 1U-6683 Ring Expander 1
B
393-2568 Bearing Removal Tool 1
443-9447 Support Plate 1
Start By:
a. Remove pistons and the connecting rods.
Note: Make a temporary mark on the components of the piston and connecting rod assembly.
Marking the components will ensure that the components of each piston and connecting rod
assembly can be reinstalled in the original cylinder. Mark the underside of the piston on the front
pin boss. Do not interchange components.
1/3
2020/1/30

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. Position the piston and connecting rod in a soft jaw vise. Use Tooling (A) to remove three
rings (2) from piston (1).
2/3
2020/1/30

2. Remove retaining ring (4) and remove piston wrist pin (3) from piston (1).
Note: Note the position of the forged Mark (X). The forged mark is for the purposes of
correct orientation of the connecting rod assembly and piston assembly.
3. If necessary, remove bolts (7) and connecting rod bearings (6) from connecting rod (5) and
connecting rod cap (8). Inspect connecting rod bushing (9).
4. Place the piston on a suitable surface with the crown upward. Use Tooling (B) in order to
remove connecting rod bushing (9) from connecting rod (5).
5. Inspect the connecting rod for wear and damage. If necessary, replace connecting rod (5) or
replace the connecting rod bushing (9).
Note: If the connecting rod or the bush for the piston pin are replaced, refer to
Specifications, "Connecting Rods" for the correct procedure.
6. Repeat Step 1 through Step 5 in order to disassemble the remaining pistons and connecting
rods.
Thu Jan 30 23:11:42 UTC+0800 2020
3/3
2020/1/30

Shutdown SIS
Previous Screen
i05845120
Pistons and Connecting Rods - Assemble
SMCS - 1225-016
Assembly Procedure
Table 1
Required Tools
A 1U-6683 Ring Expander 1
B
393-2568 Bearing Removal Tool 1
443-9447 Support Plate 1
Values.
Note: The C3.3B has three different piston heights that very 0.05 mm (0.002 inch) from each.
Refer to the following Table 2 to ensure that the same piston height is replaced. If the same piston
height is replaced, then the same head gasket thickness can be used. If a different piston height is
used, then check the piston height to determine the proper head gasket thickness. Refer to
"Cylinder Head - Remove and Install" for the correct head gasket.
Table 2
Code Stamped on
Standard Piston
Standard Replacement
Piston
0.50 mm Oversized
Piston
Code Stamped on
Oversized Piston
1J751-2111 387-9833 393-2885 1J751-2190
1J751-2112 387-9834 393-2886 1J751-2191
1J751-2113 387-9835 393-2887 1J751-2192
1/5
2020/1/30

1. Ensure that all components are clean and free from wear and damage. If necessary, replace
any components that are worn or damaged.
2. Inspect the connecting rod for wear and damage. If necessary, replace connecting rod (5) or
replace connecting rod bushing (9) .
Note: If connecting rod (5) or the bushing (9) for connecting rod pin are replaced, refer to
Specifications, "Connecting Rods" for the correct procedure.
3. Place the piston on a suitable surface with the crown upward. Use Tooling (B) in order to
install connecting rod bushing (9) into connecting rod (5) .
4. Check connecting rod bushing (9) . If necessary, install connecting rod bearings (6) into
connecting rod (5) and connecting rod cap (8) . Inspect bolts (7) or replace with new for
assembly later.
2/5
2020/1/30

Caterpillar Cat 306E Mini Hydraulic Excavator (Prefix FHL) Service Repair Manual (FHL00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 306E Mini Hydraulic Excavator (Prefix FHL) Service Repair Manual (FHL00001 and up).pdf

Similar to Caterpillar Cat 306E Mini Hydraulic Excavator (Prefix FHL) Service Repair Manual (FHL00001 and up).pdf (7)

More from mbk336997

More from mbk336997 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 306E Mini Hydraulic Excavator (Prefix FHL) Service Repair Manual (FHL00001 and up).pdf