The document provides instructions for assembling a piston motor. It details 17 steps to install various parts like bearings, seals, springs, and retaining rings. Safety warnings are included to properly handle parts under spring tension. Tools required include retaining ring pliers and a driver. The assembly is then installed by references to other documents.
The document provides instructions for assembling and disassembling various components of an excavator, including:
1. Assembling the piston motor by installing various parts like bearings, seals, springs, and retaining rings in 17 steps.
2. Installing the assembled piston motor and fan motor assembly along with attaching bolts and bending locking tabs.
3. Disassembling the hydraulic lockout control by removing retaining rings, levers, springs, and pins over 5 steps.
4. Reassembling the hydraulic lockout control by reversing the disassembly steps over 6 steps.
5. Installing the assembled hydraulic lockout control along with bolts, screws, and attaching
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...zatao0179249295
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...luanxianshi27
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then explains installing the assembled piston motor and attaching a fan motor assembly. Finally, it outlines installing the hydraulic lockout control unit with bolts, screws, and a cable strap.
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then details installing the assembled piston motor and attaching a fan motor assembly. Finally, it explains how to install the hydraulic lockout control unit with bolts and screws, and attaching a switch and cable strap.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...cnp692569
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps for assembling the piston motor, including installing bearings, seals, springs, and retaining rings. It also describes removing and disassembling the hydraulic lockout control into individual parts and reassembling it. Safety precautions are provided for parts under spring tension.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
The document provides instructions for assembling and disassembling various components of an excavator, including:
1. Assembling the piston motor by installing various parts like bearings, seals, springs, and retaining rings in 17 steps.
2. Installing the assembled piston motor and fan motor assembly along with attaching bolts and bending locking tabs.
3. Disassembling the hydraulic lockout control by removing retaining rings, levers, springs, and pins over 5 steps.
4. Reassembling the hydraulic lockout control by reversing the disassembly steps over 6 steps.
5. Installing the assembled hydraulic lockout control along with bolts, screws, and attaching
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...zatao0179249295
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...luanxianshi27
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then explains installing the assembled piston motor and attaching a fan motor assembly. Finally, it outlines installing the hydraulic lockout control unit with bolts, screws, and a cable strap.
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then details installing the assembled piston motor and attaching a fan motor assembly. Finally, it explains how to install the hydraulic lockout control unit with bolts and screws, and attaching a switch and cable strap.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...cnp692569
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps for assembling the piston motor, including installing bearings, seals, springs, and retaining rings. It also describes removing and disassembling the hydraulic lockout control into individual parts and reassembling it. Safety precautions are provided for parts under spring tension.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps for disassembly, including the sun gear, carrier assembly, ring gear, planetary gears, shafts, bearings, and housing components. Reassembly involves installing the same parts in the reverse order over 17 steps, applying sealant and fasteners, and noting torque specifications. The overall process handles each part with care to prevent contamination and properly position components using lifting devices and presses.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and barrel assembly. Small components like seals, springs, and races are also removed. Precise identification marks are needed to ensure correct reassembly of small parts and piston shoe assemblies in their original locations. Tools required for the disassembly are also listed.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual (TLF00001...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
Caterpillar Cat 312D L Excavator (Prefix HCW) Service Repair Manual (HCW00001...km7seydwuhdw
This document provides instructions for installing the crankshaft in a Caterpillar 312D or 312D L excavator. It involves the following steps:
1. Install the thrust washer and upper halves of the main bearings in the cylinder block. Lubricate and position the crankshaft onto the bearings.
2. Install the lower main bearings onto the bearing caps and rear cap. Lubricate and install seals in the rear cap grooves.
3. Install the bearing caps and tighten the bolts to specification. Check crankshaft end play and install the connecting rods, pistons, and remaining components.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves 28 steps to remove components like the head, brake piston, rotating assembly, bearings and seals. The assembly process reverses the disassembly with 23 steps, applying lubricant and torque specifications where required to reinstall components in the correct orientation. Tools including adapters, eyebolts, retaining ring pliers and presses are listed to facilitate the work.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps for disassembly, including the sun gear, carrier assembly, ring gear, planetary gears, shafts, bearings, and housing components. Reassembly involves installing the same parts in the reverse order over 17 steps, applying sealant and fasteners, and noting torque specifications. The overall process handles each part with care to prevent contamination and properly position components using lifting devices and presses.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and barrel assembly. Small components like seals, springs, and races are also removed. Precise identification marks are needed to ensure correct reassembly of small parts and piston shoe assemblies in their original locations. Tools required for the disassembly are also listed.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual (TLF00001...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
Caterpillar Cat 312D L Excavator (Prefix HCW) Service Repair Manual (HCW00001...km7seydwuhdw
This document provides instructions for installing the crankshaft in a Caterpillar 312D or 312D L excavator. It involves the following steps:
1. Install the thrust washer and upper halves of the main bearings in the cylinder block. Lubricate and position the crankshaft onto the bearings.
2. Install the lower main bearings onto the bearing caps and rear cap. Lubricate and install seals in the rear cap grooves.
3. Install the bearing caps and tighten the bolts to specification. Check crankshaft end play and install the connecting rods, pistons, and remaining components.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves 28 steps to remove components like the head, brake piston, rotating assembly, bearings and seals. The assembly process reverses the disassembly with 23 steps, applying lubricant and torque specifications where required to reinstall components in the correct orientation. Tools including adapters, eyebolts, retaining ring pliers and presses are listed to facilitate the work.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g01207276
15. Lower the temperature of bearing cup (5).
16. Install bearing cup (5), port plate (4), and O-ring seal (3).
Illustration 13 g01207275
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install head (2) and bolts (1).
End By:
a. Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install".
6/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415453
Piston Motor (Hydraulic Fan) - Install
SMCS - 1386-012-QP; 5058-012-FM
installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01207418
1. Use a suitable lifting device to install piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
2. Install bolts (6).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g01207416
3. Use a suitable lifting device to reposition fan motor assembly (4), as shown. The weight of
fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207415
4. Install hub (3) and bolts (2).
5. Bend locking tabs (1) over bolts (2).
End By:
a. Install the fan. Refer to Disassembly and Assembly, "Fan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 10 23:59:03 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02554917
Hydraulic Lockout Control - Remove
SMCS - 5001-011-LK
Removal Procedure
Illustration 1 g01187398
1. Remove screws (2) and panel (1).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01278781
2. Remove screws (6). Cut cable strap (8) and place switch (7) aside.
3. Remove bolt (4), bolt (5), and hydraulic lockout control (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 10 23:59:59 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378526
Hydraulic Lockout Control - Disassemble
SMCS - 5001-015-LK
Disassembly Procedure
Start By:
a. Remove the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Remove".
Illustration 1 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
1/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove retaining rings (1) and lever assembly (2).
2. Remove retaining ring (4), lever assembly (5), and spring (3).
Illustration 2 g01187383
3. Pull back cover (8) in order to remove pin (7) from pipe assembly (6).
Illustration 3 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 4. Remove pin (10) from pin (9).
5. Remove spring (11) from cover (12).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:00:55 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378527
Hydraulic Lockout Control - Assemble
SMCS - 5001-016-LK
Assembly Procedure
Illustration 1 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Install spring (11) to cover (12).
2. Install pin (10) to pin (9).
Illustration 2 g01187383
3. Install pin (7) to pipe assembly (6).
4. Slide cover (8) over pipe assembly (6).
Illustration 3 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Install spring (3), lever assembly (5), and retaining ring (4).
2/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 6. Install lever assembly (2) and retaining rings (1).
End By:
a. Install the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:01:51 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07426591
Hydraulic Lockout Control - Install
SMCS - 5001-012-LK
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 243 -
Illustration 1 g01278781
1. Install hydraulic lockout control (3), bolt (4), and bolt (5).
2. Apply Tooling (A) to the threads of screws (6). Position switch assembly (7) and install
screws (6). Tighten screws (6) to a torque of 0.7 ± 0.1 N·m (6.2 ± 0.9 lb in). Attach cable
strap (8).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01187398
3. Install panel (1) and screws (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:02:47 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02417256
Operator Console - Remove and Install
SMCS - 5258-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Start By:
a. Remove the seat. Refer to Disassembly and Assembly, "Seat - Remove".
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01208165
1. Remove plates (1) and (2).
Illustration 2 g01196137
2. Attach Tooling (A) and an air supply to the hydraulic oil tank. Apply 345 ± 70 kPa
(50 ± 10 psi) to Tooling (A).
2/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 6. Disconnect harness assemblies (6).
Illustration 7 g01208204
7. Remove plate (8). Move floor mat (7) toward the front of the cab.
Illustration 8 g01208208
8. Remove bolts (9) from each side of the operator console. Pull hose assemblies (3) and (4)
through the floor of the cab. Hose assemblies (3) and (4) were removed in Steps 3 and 4.
Pull harness assemblies (5) and (6) through the floor of the cab. Harness assemblies (5) and
(6) were removed in Steps 5 and 6.
Note: If the machine is equipped with a radio, the antenna will need to be disconnected.
4/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 9 g01208250
9. Disconnect harness assembly (10).
Illustration 10 g01208252
10. Remove bolts (11) and operator console (12).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Illustration 11 g01208252
1. Install operator console (12) and bolts (11).
5/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 12 g01208250
2. Connect harness assembly (10).
Illustration 13 g01208208
3. Insert hose assemblies (3) and (4) through the hole in the cab floor. Insert harness
assemblies (5) and (6) through the holes in the cab floor. Hose assemblies (3) and (4) and
harness assemblies (5) and (6) will be connected in the following steps. Install bolts (9)
from each side of the operator console.
Note: If the machine is equipped with a radio, the antenna will need to be connected.
Illustration 14 g01208204
6/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 4. Move floor mat (7) toward the rear of the cab. Install plate (8).
Illustration 15 g01208202
5. Connect harness assemblies (6).
Illustration 16 g01208198
6. Connect harness assemblies (5).
Illustration 17 g01208191
7. Connect hose assemblies (4).
7/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...