Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair Manual (CDY00001 and up).pdf

Service Repair Manual
Models
W345B Series II Material
Handler

Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: W345B II WHEELED EXCAVATOR CDY
Configuration: W345B Series II Material Handlers CDY00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i02830548
Swing Drive - Assemble
SMCS - 5459-016
S/N - AGS1-UP
S/N - AKX1-UP
S/N - ALB1-UP
S/N - ALD1-UP
S/N - AMD1-UP
S/N - AMJ1-UP
S/N - AMN1-UP
S/N - ANJ1-UP
S/N - APB1-UP
S/N - AYR1-UP
S/N - CCC1-UP
S/N - CDY1-UP
S/N - DCW1-UP
S/N - DET1-UP
S/N - FEE1-UP
Assembly Procedure
1/14(W)
w
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C
5P-5197 Retaining ring pliers 1
1U-8759 Tip Set 1
D 1P-0510 Drive Group 1
E 1U-6396 O-Ring Assembly Compound 1
F 5P-3931 Anti-Seize Compound 1
G 5P-0960 Molybdenum Grease 1
H 9S-3263 Thread Lock Compound 1
J 1U-8846 Gasket Sealant 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use Tooling (E) during the assembly procedure.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Make sure that all parts of the swing drive are thoroughly clean and free of dirt and debris
prior to assembly.
2/14(W)
w
2020/5/27

Illustration 1 g00725394
2. Apply Tooling (F) on the outside diameter of bearing (37) and the inside diameter of swing
drive housing (19) .
3. Lower the temperature of bearing (37) . Install bearing (37) in the swing drive housing.
4. Install O-ring seal (35) into bearing cage (31) .
5. Install the two lip seals (34) in bearing cage (31) .
6. Apply Tooling (G) on the lip of each seal.
3/14(W)
w
2020/5/27

7. Carefully install cage (31) over pinion shaft (33) .
8. Heat bearing (39) to a temperature of 135 °C (275 °F) and install bearing (39) on the pinion
shaft (33) .
4/14(W)
w
2020/5/27

9. Install spacer (38) on top of bearing (37) , as shown.
Note: Lip (e) for spacer (38) must face opposite bearing (37) , as shown.
10. Put swing drive housing (19) in the press.
11. Apply Tooling (F) on the outside diameter of bearing (39) and the inside diameter of the
swing drive housing.
12. Install pinion shaft (33) , bearing cage (31) , bearing assembly (39) , through spacer (38)
and bearing (37) .
Note: It may be necessary to reposition the press so that bearing assembly (39) is installed
evenly into the swing drive housing.
Note: Align bearing cage (31) with the swing drive housing during installation of the pinion
shaft. Temporarily install two bolts that will hold bearing cage (31) to the swing drive
housing.
5/14(W)
w
2020/5/27

13. Remove the swing drive from the press and place the swing drive sideways. The combined
weight of the swing drive housing, the pinion shaft, and the bearing cage is 152 kg (335 lb).
14. Remove the temporary bolts that are holding the bearing cage in position.
15. Apply Tooling (H) on the threads of bolts (32) that hold bearing cage (31) to swing drive
housing (19) .
16. Tighten bolts (32) to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
17. Heat bearing cone (36) to a temperature of 135 °C (275 °F). Install bearing cone (36) on the
pinion shaft (33) .
Note: Make sure that the shaft is centered in the swing drive housing, before you install
bearing cone (36) .
18. Use Tooling (C) to install retaining ring (30) .
19. Assemble the carrier assembly (21) , as follows:
6/14(W)
w
2020/5/27

a. Apply clean SAE 30W oil on bearing (26) and bearing (28) . Install bearings (26) and
(28) into planetary gear (27) .
b. Install thrust washer (25) on one side of planetary gear (27) .
c. Install thrust washer (29) on the opposite side of planetary gear (27) .
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (27) and the thrust washers in the carrier assembly (21) .
f. Install planetary shaft (24) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
7/14(W)
w
2020/5/27

g. Drive spring pin (23) into shaft (24) . Orient the split in spring pin (23) vertically to
the carrier. Align the split in the spring pin to the top or to the bottom. Make a stake
mark on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 19.a through 19.g in order to install the remaining planetary gears (27)
in the carrier.
20. Use two people and install carrier assembly (21) into the housing. The weight of carrier
assembly (21) is approximately 40 kg (88 lb).
8/14(W)
w
2020/5/27

21. Install retaining ring (22) .
22. Install spacer (20) into carrier assembly (21) .
9/14(W)
w
2020/5/27

23. Make sure that the mating surfaces of the ring gear (18) and the swing drive housing (19)
are thoroughly clean.
24. Apply Tooling (J) to the face of swing drive housing (19) and the face of ring gear (18) .
25. Install Tooling (A) onto ring gear (18) . Weight of the ring gear is approximately 36 kg (80
lb).
26. Install ring gear (18) onto the swing drive housing (19) .
27. Install retaining ring (17) into the sun gear.
28. Install carrier (7) into the sun gear. Install retaining ring (15) into sun gear (16) .
29. Assemble carrier assembly (7) , as follows:
10/14(W)
w
2020/5/27

a. Apply clean SAE 30W oil on bearing (13) . Install bearing (13) in planetary gear
(12) .
b. Install a thrust washer (11) on one side of planetary gear (12) .
c. Install a thrust washer (14) on the opposite side of planetary gear (12) .
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (12) and the thrust washers in the carrier assembly (7) .
f. Install planetary shaft (10) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
11/14(W)
w
2020/5/27

g. Drive spring pin (9) into shaft (10) . Orient the split in spring pin (9) vertically to the
carrier. Align the split in the spring pin to the top or to the bottom. Make a stake mark
on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 29.a through 29.g for the remaining gear assemblies.
30. Install carrier assembly (7) in the ring gear.
31. Install spacer (8) into carrier assembly (7) .
12/14(W)
w
2020/5/27

32. Install sun gear (6) into carrier assembly (7) .
33. Make sure that the mating surfaces of the ring gear and cover (5) are thoroughly clean.
34. Apply Tooling (J) on the flange surface of the ring gear and cover (5) .
35. Fasten Tooling (A) and a suitable lifting device to cover (5) . Put the cover in the original
position on the ring gear. Make sure that the cover is seated properly.
13/14(W)
w
2020/5/27

36. Apply Tooling (H) on the threads of bolts (4) .
37. Install the washers and bolts (4) that hold the cover, the ring gear, and the swing drive
housing together. Tighten bolts (4) to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
38. Install fitting (3) into cover (5) .
39. Install oil level gauge (Dipstick) (1) , filler breather cap assembly and hose assembly (2) to
the swing drive.
40. If the drain valve was removed from the swing drive housing, reinstall the drain valve.
End By: Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 01:20:39 UTC+0800 2020
14/14(W)
w
2020/5/27

Shutdown SIS
Previous Screen
i01450853
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
(A)
132-8223 110 volt Power Pack (1)
1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
(B) 138-7573 Link Bracket 4
( 1 )
132-8231 220 volt Power Pack is available.
1. The following installation procedure is identical for both swing drives.
2. Thoroughly clean the mating surfaces of the swing drive housing and the main frame.
3. Apply 5P-3931 Anti-Seize Compound on the locating pin in the main frame. Also, apply 5P
-3931 Anti-Seize Compound in the pin bore in the main frame.
4. Apply 1U-8846 Sealant on the mating surface of the main frame and the swing drive
housing.
1/3(W)
w
2020/5/27

Note: During installation, the locating pin for the swing drive can come out of the swing
drive housing.
5. Fasten Tool (B) and a hoist to swing drive (3). The weight of the swing drive is 227 kg (500
lb). Place the swing drive in the swing drive's original position in the main frame. If the
locating pin comes out of the swing drive housing, the locating pin can be reinstalled with a
hammer after the swing drive is in place.
6. Apply 9S-3263 Thread Lock Compound on the threads of bolts (1). Install the bolts and the
washers that hold the swing drive in place. Tighten the bolts evenly with Tooling (A) to a
torque of 900 ± 100 N·m (665 ± 75 lb ft).
7. Install two corks (2) in the threaded holes in the swing drive housing.
8. After installation of the swing motor, fill the hydraulic oil tank and the swing drive with oil
to the proper level.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Refill Capacities" for the correct
amount.
2/3(W)
w
2020/5/27

Reference: Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level -
Check" for the correct filling procedures.
Reference: Refer to Operation and Maintenance Manual, "Swing Drive Oil Level - Check"
for the correct filling procedures.
End By: Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install" in
this manual.
Wed May 27 01:21:36 UTC+0800 2020
3/3(W)
w
2020/5/27

Shutdown SIS
Previous Screen
i01187801
Swing Gear and Bearing - Remove
SMCS - 7063-011
Removal Procedure
Table 1
Required Tools
(A) 138-7574 Link Bracket 4
(B)
132-8223 115 volt Power Pack 1
132-8112 3/4 inch Drive Torque Wrench 1
9U-6529 24 mm Socket 1
Start By:
a. Remove the undercarriage frame assembly. Refer to Disassembly and Assembly, "Undercarriage
Frame - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/5/27

1. Remove all of the grease from the swing gear and bearing. Put the grease in a suitable container for
storage or disposal.
2. Put an alignment mark on swing gear and bearing (1) and the undercarriage frame assembly for
installation purposes.
3. Fasten Tooling (A) and a suitable lifting device to swing gear and bearing (1), as shown. Put a slight
lifting tension on the swing gear and bearing.
4. Use Tooling (B) to remove bolts (2) and the spacers that secure swing gear and bearing (1) to the
undercarriage frame assembly.
5. Carefully remove the swing gear and bearing from the undercarriage frame assembly. The weight of
the swing gear and bearing is 454 kg (1000 lb).
2/3(W)
w
2020/5/27

6. Place tape over the sealing surfaces of the dust seals, the inner race and the outer race. This will
prevent cleaning solvent from entering the cross sections of the dust seals. Thoroughly clean the
swing gear and bearing.
7. Remove dust seals (3) and (4) from the outer race and the inner race of the swing gear and bearing.
8. Clean the sealing grooves of the inner race and outer race with fine grit sandpaper. Use a cleaning
solvent to clean the seal grooves. Make sure that the seal grooves are thoroughly clean and dry prior
to installing new dust seals.
Wed May 27 01:22:33 UTC+0800 2020
3/3(W)
w
2020/5/27

Shutdown SIS
Previous Screen
i07191587
Swing Gear and Bearing - Install
SMCS - 7063-012
Installation Procedure
Table 1
Required Tools
A 439-3941 Link Bracket As 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
C - Loctite 435 -
D 2P-9066 Lubricant 1
E 1U-8846 Gasket Sealant 1
F - Loctite C5A Copper Anti-Seize -
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Note: If the inner dust seal (3) and the outer dust seal (4) are installed dry, the new dust seals should
be installed dry in the swing gear and bearing.
Note: If the inner dust seal and the outer dust seal are bonded to the swing gear and bearing, the new
dust seals should be bonded to the swing gear and bearing.
Note: Perform Steps 1.a through 1.j to install the new dry dust seals.
Note: Perform Steps 2.a through 2.p to install the new dust seals that are bonded to the swing gear
and bearing.
1/6(W)
w
2020/5/27

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. If inner dust seal (3) and outer dust seal (4) were installed dry, use the following procedure to install
the new dust seals:
a. Use a wire brush to thoroughly clean the grooves for the dust seal of the swing gear and
bearing. Make sure that all the dirt and foreign material has been removed.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seal in the swing gear and bearing are thoroughly clean
and dry prior to installation of the dust seals.
d. Cut one end of inner dust seal (3) at a 90 degree angle. Use a blunt tool to install the inner dust
seal in the seal groove of the swing gear and bearing.
e. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
f. After the inner dust seal is installed in the seal groove, measure the seal and cut the remaining
end of the inner dust seal at a 90 degree angle. Install the remaining end of the inner dust seal
in the seal groove.
g. Make sure that the inner dust seal is seated properly in the seal groove, all the way around the
swing gear and bearing. Also, make sure that there is no gap between the ends of the inner dust
seal.
h. Pull each end of the inner dust seal out of the seal groove of the swing gear and bearing
approximately 50.8 mm (2.00 inch). Apply Tooling (C) to each end of the inner dust seal to
bond the seals together.
i. Immediately reinstall the inner dust seal in the seal groove of the swing gear and bearing.
Again, make sure that the entire inner dust seal is properly seated in the seal groove of the
swing gear and bearing. No gap should exist between the ends of the inner dust seal.
j. To ensure that the lip of inner dust seal has not adhered to the top of the bearing at the seal
joint, run a dull putty knife between the lip of the seal and the bearing at the seal joint.
k. Follow the procedure in Steps 1.a through 1.j to install outer dust seal (4) in the swing gear and
bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
2/6(W)
w
2020/5/27

2. If inner dust seal (3) and outer dust seal (4) were bonded in the swing gear and bearing, use the
following procedure to install the new dust seals:
a. Thoroughly clean all the dirt and foreign material from the grooves for the dust seal in the
swing gear and bearing with a wire brush.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seals in the swing gear and bearing are thoroughly
clean and dry prior to installation of the dust seals.
Note: Install inner dust seal (3) and outer dust seal (4) in the swing gear and bearing in small
increments, because Tooling (C) cures very quickly.
d. Cut one end of inner dust seal (3) at a 90 degree angle.
e. Start applying Tooling (C) 50.8 mm (2.00 inch) from the cut end of the seal. Apply Tooling
(C) to the seal in 152.4 mm (6.00 inch) increments.
f. Immediately use a blunt tool to install only the bonded portion of the inner dust seal in the seal
groove of the swing gear and bearing. Make sure that the dust seal is seated properly in the
seal groove.
g. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
h. To ensure that the inner dust seal has not adhered to the bearing, run a dull putty knife between
the lip of the seal and the bearing.
i. Apply Tooling (C) to the next 152.4 mm (6.00 inch) of the seal. Immediately use a blunt tool
to install only the bonded portion of the inner dust seal in the seal groove of the swing gear and
bearing.
j. Make sure that the inner dust seal is seated properly in the seal groove. Ensure that the inner
dust seal has not adhered to the bearing.
Note: Do not install the last 152.4 mm (6.00 inch) of the inner dust seal.
k. Repeat Steps 2.i through 2.j until the dust seal is installed.
l. Measure the inner dust seal and cut the remaining end of inner dust seal (3) at a 90 degree
angle. Install the last 152.4 mm (6.00 inch) of seal in the seal groove dry.
m. Make sure that the inner dust seal is properly seated in the seal groove and that there is no gap
between the seal ends. Carefully remove both loose ends of the inner dust seal out of the seal
groove.
n. Apply Tooling (C) to the loose ends of the seal.
o. Immediately use a blunt tool to reinstall the seal ends in the seal groove. Again, make sure that
the inner dust seal is properly seated in the seal groove, and that no gap existed between the
ends of the seal.
p. To ensure that the inner dust seal has not adhered to the top of the bearing, run a dull putty
knife around the seal.
q. Follow the procedure in Steps 2.a through 2.p to install outer dust seal (4) in the swing gear
and bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
3. Lubricate the swing gear and bearing with grease.
3/6(W)
w
2020/5/27

Note: Clean the mating surface for the swing gear and bearing on the undercarriage frame assembly.
4. Apply Tooling (E) on the mating surface for the swing gear and bearing of the undercarriage frame
assembly.
5. Fasten Tooling (A) and a suitable lifting device to swing gear and bearing (1), as shown. Refer to
Illustration 2. The weight of swing gear and bearing (1) is approximately 660 kg (1455 lb).
6. Place the swing gear and bearing in the swing gear and bearing's original position on the
undercarriage frame assembly.
7. Make sure that the stamp "S" on the inner race is in the position that is shown, relative to the
undercarriage frame assembly and the stopper on the outer race. Refer to Illustration 3.
4/6(W)
w
2020/5/27

Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair Manual (CDY00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair Manual (CDY00001 and up).pdf

Similar to Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair Manual (CDY00001 and up).pdf (10)

More from jdksme9ddkkd

More from jdksme9ddkkd (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair Manual (CDY00001 and up).pdf