Caterpillar Cat D4E TRACK TRACTOR (Prefix 2CB) Service Repair Manual (2CB00001 and UP).pdf

Service Repair Manual
Models
D4E TRACK TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D4E TRACK-TYPE TRACTOR 2CB
Configuration: D4E TRACTOR-SPECIAL APPLICATION / DIRECT DRIVE / 2CB00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
D4E TRACTOR-SPECIAL APPLICATION / DIRECT DRIVE / 2CB00001-UP (MA...
2019/8/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal is
damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/4
2019/8/31

3. Remove center bolt (3) and spacer (4).
4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown.
Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection pump
camshaft.
5. Remove Tool (A) and bolt (3).
3/4
2019/8/31

6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9).
Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6) with
the filter and the gasket.
7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket.
Remove tube assembly (13).
8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor.
Note: Remove the heat shield (not shown) if equipped.
9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the
washers. Remove the fuel injection pump housing and the governor from the engine. To safely
remove the fuel injection pump housing and the governor, use two technicians or a suitable
lifting device. The weight of the 3304B fuel injection pump housing and governor is 24 kg
(53 lb). The weight of the 3306B fuel injection pump housing and governor is 32 Kg (70 lb).
10. Remove the O-ring seals from the fuel injection pump housing and the governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 31 11:32:27 UTC+0800 2019
4/4
2019/8/31

Shutdown SIS
Previous Screen
i01139602
Fuel Injection Pump Housing - Disassemble
SMCS - 1253-015
Disassembly Procedure
Table 1
Required Tools
A 1P-1860 Retaining Ring Pliers 1
Start By:
A. Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
B. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
1/5
2019/8/31

1. Remove cover (1) and the gasket.
2. Remove fuel rack (2) from the fuel injection pump housing.
Note: If the original lifters are being reused in the fuel injection pump housing, place
identification marks on the lifters in order to identify the locations.
2/5
2019/8/31

3. Remove lifters (3) from the fuel injection pump housing.
4. Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order to
remove snap ring (4) .
5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump
housing in order to loosen washer (5). Remove washer (5) .
3/5
2019/8/31

6. Remove camshaft (6) .
7. Remove bearings (7) from the drive end of the fuel injection pump housing.
8. Remove bearings (8) from the governor end of the fuel injection pump housing.
4/5
2019/8/31

Sat Aug 31 11:33:21 UTC+0800 2019
5/5
2019/8/31

Shutdown SIS
Previous Screen
i01138035
Fuel Injection Pump Housing - Assemble
SMCS - 1253-016
Assembly Procedure
Table 1
Required Tools
A 1P-1860 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C
6V-2016 Plate 1
0S-1594 Bolt 2
6V-4818 Driver 1
NOTICE
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are clear.
1/6
2019/8/31

1. Use Tool (B) in order to install large bearing (1) in the governor end of the fuel injection
pump housing. Bearing joint (3) should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 0.25 ± 0.20 mm (.010 ± .008 inch) below the
surface of the fuel injection pump housing.
2. Use Tool (B) in order to install small bearing (2) in the governor end of the fuel injection
pump so that Tool (B) is 7.16 ± 0.13 mm (.282 ± .005 inch) below the surface of the fuel
injection pump housing.
3. Use Tool (B) in order to install large bearing (4) in the drive end of the fuel injection pump
housing. The bearing joint should be facing toward the top of the fuel injection pump housing.
Install the bearing so the bearing is 1.00 ± 0.25 mm (.039 ± .010 inch) below the surface of
the fuel injection pump housing.
2/6
2019/8/31

4. Install the plate of Tool (C) on the drive end of the fuel injection pump in order to install small
bearing (5) for the rack. Use clean grease in order to hold the new driver for the rack bearing
of Tool (C). Install the driver and the bearing in the plate. Ensure that the groove in the driver
is aligned with the pin in the plate and use a hammer to push the bearing into position. The
bearing will be installed to the correct depth when the shoulder of the driver is against the
plate.
5. Remove Tool (C) from the fuel injection pump housing. The fuel rack bearing must be
installed so that the fuel rack bearing is 0.25 ± 0.25 mm (.010 ± .010 inch) below the surface
of the housing.
6. Install camshaft (6) .
3/6
2019/8/31

7. Put the fuel injection pump housing upright, as shown. Place a wood block under the
camshaft.
8. Put washer (7) over the end of the camshaft. Use Tool (B) and spacer (8) in order to push the
washer against the seat on the camshaft. Spacer (8) has an inside diameter of 38.1 mm (1.50
inch) and a length of 31.75 mm (1.250 inch). The camshaft must have an end play of 0.18 ±
0.08 mm (.007 ± .003 inch) when the washer is pushed against the shoulder of the camshaft.
9. Use Tool (A) in order to install snap ring (9) .
4/6
2019/8/31

Note: Check the condition of the new lifters. Replace the lifters, if necessary. If the original
lifters are being reused, place the lifters in the original locations. New lifters are identical, and
the new lifters can be placed in any order.
10. Install six lifters (10) in the fuel injection pump housing. Ensure that the groove in the lifter is
aligned with the pin in the fuel injection pump housing.
11. Install rack (11). Ensure that the groove in the end of the rack is aligned with the ear (tab) of
the fuel rack bearing that is at the drive end of the fuel injection pump housing.
5/6
2019/8/31

12. Install the gasket and cover (12) .
End By:
a. Assemble the governor. Refer to Disassembly and Assembly, "Governor - Assemble".
b. Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
Sat Aug 31 11:34:15 UTC+0800 2019
6/6
2019/8/31

Shutdown SIS
Previous Screen
i01111133
Fuel Injection Pump Housing and Governor - Install
SMCS - 1286-012
Installation Procedure
Table 1
Required Tools
A 5P-7307 Engine Turning Tool 1
B 4C-9874 Spanner Wrench 1
C 6V-4186 Fuel Pump Timing Pin 2
NOTICE
Note: The No. 1 piston must be set at the top center position (TC) in order to perform all of the
timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft rotation is
given.
1/6
2019/8/31

1. Remove the electric starting motor.
2. Install Tool (A) into the flywheel housing, as shown.
3. To find the TC position for the No. 1 piston, perform the following procedure:
a. Turn the flywheel clockwise or turn the flywheel in the opposite direction of the engine
rotation for approximately 30 degrees. This removes all play from the timing gears.
Note: If you go past the bolt hole, repeat Step 3.a.
b. Remove plugs (1) and (2) .
2/6
2019/8/31

c. Turn the flywheel counterclockwise until a 3/8-16 X 3 1/2 NC bolt (4) can be installed
in the flywheel through the hole in the flywheel housing. The No. 1 and No. 6 pistons
are now at the TC position. Plug (2) was removed for viewing through inspection hole
(3) .
Note: The No. 1 piston is on the compression stroke when the valves of the No. 1
cylinder are closed. The rocker arms for the inlet valves and for the exhaust valves must
have slight side-to-side movement.
d. In order to check the position of the inlet and exhaust valves, remove the valve
mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
4. If the No. 1 piston is not on the compression stroke, remove bolt (4) and turn the flywheel for
360 degrees counterclockwise. Install bolt (4). The No. 1 piston is now at the TC position.
Typical example
5. Install Tool (C) in the fuel injection pump housing, as shown. Push on Tool (C) and turn fuel
injection pump camshaft (8). When Tool (C) engages the groove (slot) in the camshaft, the
fuel injection pump is in the TC position for the No. 1 piston.
3/6
2019/8/31

Note: Check the condition of the O-ring seals. Replace the O-ring seals, if necessary.
6. Ensure that O-ring seals (5), (6), (7) and (9) are in position on the fuel injection pump housing
and the governor. Put clean engine oil on the seals.
7. Attach a hoist and put the fuel injection pump housing and the governor in position on the
timing gear plate and the oil manifold. Install three nuts (11), two bolts (10) and the washers.
Ensure that Tool (C) remains in place.
8. Install washer (12) with the large side outward. Install bolt (13) finger tight. Ensure that Tool
(C) is in the notch in the camshaft of the fuel injection pump.
4/6
2019/8/31

9. Install Tool (B) on the fuel pump drive gear. Apply 68 N·m (50 lb ft) of force to the fuel
pump drive gear with timing bolt (3) in position in the flywheel and Tool (C) in position in the
fuel system. Apply this force in a clockwise direction when the engine is viewed from the
front. Use Tool (B) and a suitable torque wrench. Hold the 68 N·m (50 lb ft) of force on Tool
(B) and torque the drive gear bolt to a torque of 270 ± 25 N·m (200 ± 18 lb ft). Remove Tool
(B) and Tool (C) from the fuel pump and remove bolt (3) from the flywheel.
10. Use Tool (A) and turn the flywheel for two complete revolutions. When bolt (3) goes in the
hole in the flywheel and Tool (C) is installed in the notch in the camshaft, the timing is
correct.
11. Install plugs (1) and (2) .
12. Remove Tool (A). Install the electric starting motor.
13. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
14. Put cover (14) and the gasket in position. Install four bolts (15) .
15. Put the fuel filter base, the gasket, and fuel filter (16) in position. Install two bolts (19) and the
washers.
5/6
2019/8/31

16. Install tube assemblies (21) and (22). Connect wire (20). Connect hoses (17) and (18) .
17. On the 3304B engines, install the strainer assembly in the turbocharger with the screen
downward. Install the gasket, the oil inlet line and the bolts. Install the O-ring seal on oil drain
line (25). Apply clean engine oil to the O-ring seal and install the gasket. Connect oil drain
line (25) and install the bolts. Install the clamps on the oil line.
18. Put cover (24) in position. Install nuts (23) and six washers. Tighten nuts (23) to a torque of
27 ± 7 N·m (20 ± 5 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Sat Aug 31 11:35:09 UTC+0800 2019
6/6
2019/8/31

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
i00886792
Governor - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
A 1P-0510 Driver Group 1
B 6V-2163 Spring Clamp 1
C 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the fuel injection pump housing and the governor. Refer to Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Remove".
Note: To remove the governor for the disassembly of the fuel injection pump housing, perform
Steps 1, 2, 16, 22, 24, 25, 26, 27, 30, 32 and 34.
NOTICE
1/12(W)
w
2019/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

1. Remove fuel ratio control (1) from governor (2) .
Note: Illustration 2 shows the fuel ratio control that is still connected.
2. Remove six bolts (3), two bolts (5), housing (4) and the gasket.
2/12(W)
w
2019/9/2

3. Remove governor spring (7), seat (6) and the washers.
4. Remove six bolts (8), cover (9) and the gasket. Use Tool (A) in order to remove seal (10) .
5. Remove low idle adjustment screw (12) and spring (11) .
3/12(W)
w
2019/9/2

6. Remove shaft assembly (15) and levers (14) and (13) .
7. Remove two snap rings (19) from two pins (17). Remove two pins (17). Remove plates (16)
and stop (18) .
8. Remove pins (21) and (22) and remove spring (20) .
4/12(W)
w
2019/9/2

9. Remove two bolts (23), and the washers, and remove adapter (24), the coupling, and the O-
ring seal.
10. Remove contact (27) and body (28) with an O-ring seal.
11. Remove two bolts (29) and the washers and remove cover (30) and the gasket.
12. Remove two nuts and washers (26) and remove shutoff solenoid (25) and the gasket.
13. Remove shaft (31) and lever (32) .
5/12(W)
w
2019/9/2

Note: The check valve will be damaged during removal. Remove check valve (33) only if a
replacement is necessary.
14. Remove check valve (33) only if a replacement is necessary.
15. Remove seal (34) and adjustment screw (35) .
6/12(W)
w
2019/9/2

Caterpillar Cat D4E TRACK TRACTOR (Prefix 2CB) Service Repair Manual (2CB00001 and UP).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat D4E TRACK TRACTOR (Prefix 2CB) Service Repair Manual (2CB00001 and UP).pdf

Similar to Caterpillar Cat D4E TRACK TRACTOR (Prefix 2CB) Service Repair Manual (2CB00001 and UP).pdf (14)

More from fyhsejdkkdmmd3e

More from fyhsejdkkdmmd3e (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat D4E TRACK TRACTOR (Prefix 2CB) Service Repair Manual (2CB00001 and UP).pdf