Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn01050 and up)

Service Repair Manual
Models
436C BACKHOE LOADER

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 9JN
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 9JN01050-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01083652
Fuel Injection Pump - Remove - Type 1 Engines and 9RM
Engines
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-9774 Bolt Remover (1)
1
B 9U-6198 Crankshaft Turning Tool 1
C
8S-2264 Puller Group 1
8S-4712 Bolt 2
( 1 )
The bolt remover is required in order to remove the tamper proof bolts on the access cover for the fuel injection
pump.
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
B. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Note: For a complete description of Type 1 and Type 2 engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
1/4436C Backhoe Loader Center Pivot, Single Tilt 9JN01050-UP (MACHINE) POWERE...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00545256
1. Remove four bolts (1) .
Note: Some engines may have four tamper proof bolts (1). Use Tool (A) in order to remove
the tamper proof bolts bolts.
2. Remove cover (2) .

3. Remove nut (3) and the lockwasher.
4. Use Tool (B) to rotate the crankshaft until keyway (X) is at 30 degrees from the vertical
centerline.

5. Install Tool (C) .
6. Disengage the gear from the fuel injection pump.
7. Disconnect hose (7) from the fuel injection pump.
8. Remove three nuts (6) that hold fuel injection pump (5) in position.
9. Remove fuel injection pump (5) and the gasket.
Note: Ensure that you do not lose the key when the fuel injection pump is removed. Also
notice the position of marks (4) in order to ensure proper alignment of fuel injection pump
(5) during installation.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 07:39:31 UTC+0800 2019

Shutdown SIS
Previous Screen
i02046409
Fuel Injection Pump - Install - Type 2 Engines and 7BJ
Engines
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
A
150-3992 Timing Pin (1)
1
150-3993 Timing Pin (2)
1
B
171-1085
or
173-9774
Tamper Resistant Tool Gp 1
( 1 )
Tooling (A) is required in order to install Bosch fuel injection pumps.
( 2 )
Tooling (A) is required in order to install Dephi (Lucas) and Stanadyne fuel injection pumps.
NOTICE

Typical example
1. Check the condition of O-ring seal (13) on fuel injection pump (12). If the seal is worn or
damaged, replace the seal.
2. Lightly lubricate O-ring seal (13) with clean engine oil. Install O-ring seal (13) on fuel
injection pump (12) .
NOTICE
The No. 1 cylinder must be at the top center position on the
compression stroke before the fuel injection pump is installed. If the
crankshaft needs to be rotated, the fuel injection pump must be
mounted temporarily or the loose gear could cause damage to the front
housing.
Typical example

3. Put fuel injection pump (12) in position on the engine. Ensure that the timing gear is aligned
with the hub of fuel injection pump (12). Install three flange nuts (11) and tighten the flange
nuts to a torque of 28 N·m (21 lb ft).
Typical example
4. Position gear (9) on the shaft of the fuel injection pump.
Note: Some fuel injection pumps are installed with tamper proof bolts. Tooling (B) may be
necessary in order to install the tamper proof bolts.
5. Put the timing gear plate in position and install four bolts (3). Tighten the four bolts finger
tight.
Note: The fuel injection pump gear will only fit in one position. Install the gear with the
letters "C" and "M" facing away from the engine.

Typical example
6. Loosen locking screw (2) (if equipped) until locking spacer (1) moves freely. Move locking
spacer (1) into position (A). Tighten locking screw (2) to a torque of 10 N·m (7 lb ft).
Note: The location of Tooling (A) for Bosch fuel injection pumps will be located toward the
top of the fuel injection pump. The location of Tooling (A) for Dephi (Lucas) and
Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection
pump.
7. Install Tooling (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tooling
(A) into position in hole (8) in the fuel injection pump body. If Tooling (A) can be fully
seated, the fuel injection pump timing is correct. No resistance should be felt when the
timing pin is inserted into hole (8) of the fuel injection pump body.
NOTICE
The fuel injection pump may be supplied with the fuel injection pump
shaft in the locked position. The drive shaft of the fuel injection pump
must not be rotated without the spacer in position under the locking
screw. Damage to the drive shaft of the fuel injection pump will result.
8. When the timing plate is installed, rotate gear (9) by hand in a counterclockwise direction in
order to remove the backlash between gear (9) and the idler gear. Do not rotate the
crankshaft or the fuel injection pump shaft. Tighten bolts (3) to a torque of 28 N·m (21 lb
ft).
9. Remove Tooling (A) from the fuel injection pump gear.

End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Wed Oct 30 07:40:27 UTC+0800 2019

Shutdown SIS
Previous Screen
i01083913
Fuel Injection Pump - Install - Type 1 Engines and 9RM
Engines
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
A 173-9774 Bolt Remover (1)
1
( 1 )
The bolt remover is required in order to install the tamper proof bolts on the access cover for the fuel injection
pump.
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
1. Inspect the condition of the gasket for the fuel injection pump. Replace the gasket, if
necessary.

2. Install the gasket and fuel injection pump (5) .
Note: Align marks (4) that are on fuel injection pump (5) and the timing gear cover.
3. Install the key.
4. Install three nuts (6) that hold fuel injection pump (5) in position.
5. Connect hose (7) to fuel injection pump (5) .
6. Engage the gear with the fuel injection pump.
7. Install the lockwasher and nut (3) .

8. Install cover (2) and four bolts (1) .
Note: Some engines have four tamper proof bolts (1). Use Tool (A) in order to install the
four bolts.
9. Set the timing of the fuel injection pump. Refer to the Testing and Adjusting Module for the
correct procedure.
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Wed Oct 30 07:41:23 UTC+0800 2019

Shutdown SIS
Previous Screen
i01051839
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
NOTICE
containing fluids.

Typical example
1. Loosen two clamps (1) .
2. Slide hose (2) away from turbocharger (3) .
3. Remove two bolts (4) and the gasket.
4. Disconnect oil return line (6) from the cylinder block and remove the gasket.
5. Remove nuts (5) .
Typical example
6. Remove three bolts (7) .

7. Remove turbocharger (3) and the gaskets.
8. Plug all openings immediately.
Wed Oct 30 07:42:18 UTC+0800 2019

Shutdown SIS
Previous Screen
i01051906
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
NOTICE
containing fluids.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. Place an index mark on all of the components for the assembly procedure.
Typical example
2. Remove elbow (1) and the O-ring seal.
3. Remove two bolts (2) .
4. Remove hose assembly (3) and the gasket.
Typical example
5. Remove six bolts (4) .
6. Remove three clamps (5) .
7. Separate compressor housing (6) from cartridge (7) .

Typical example
Typical example
8. Remove six bolts (8) .
9. Remove three clamps (9) .
10. Separate cartridge (7) from turbine housing (10) .
Wed Oct 30 07:43:14 UTC+0800 2019

Shutdown SIS
Previous Screen
i01051989
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
NOTICE
1. Inspect the condition of the gaskets. Replace the gaskets, if necessary.
Typical example

Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn01050 and up)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn01050 and up)

Similar to Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn01050 and up) (13)

More from fujsjefksekmfm

More from fujsjefksekmfm (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn01050 and up)