2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 422E BACKHOE LOADER HBE
Configuration: 422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders
Power Train
Media Number -RENR6475-13 Publication Date -01/07/2017 Date Updated -13/07/2017
i04818786
Drive Shaft (Front) - Remove and Install
SMCS - 3253-010-FR
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
Illustration 1 g01116830
1/4422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Install Tooling (A) under guard (2) . Remove bolts (1) . Repeat for the other side. Use
Tooling (A) in order to lower guard (2) to the ground. The weight of guard (2) is
approximately 38 kg (85 lb).
Illustration 2 g01116832
2. Remove bolts (3) .
Illustration 3 g01116843
3. Remove bolts (5) and remove front drive shaft (4) .
2/4422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
Illustration 4 g01116843
1. Install front drive shaft (4) and install new bolts (5) . Tighten bolts (5) to a torque of 28 � 7
N�m (21 � 5 lb ft)
3/4422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01116832
2. Install new bolts (3) .
Illustration 6 g01116830
3. Install Tooling (A) under guard (2) . The weight of guard (2) is approximately 38 kg (85 lb).
Use Tooling (A) in order to raise guard (2) into position. Install bolts (1) . Repeat for the
other side.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 30 22:06:23 UTC+0800 2019
4/4422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 422E BACKHOE LOADER HBE
Configuration: 422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders
Power Train
Media Number -RENR6475-13 Publication Date -01/07/2017 Date Updated -13/07/2017
i02212212
Drive and Steering Axle (Front) - Remove
SMCS - 3020-011-FR
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
ZZ
6V-9829 Cap As 1
6V-9508 Plug 1
Start By:
a. Remove the tires and the rims. Refer to Disassembly and Assembly, "Tire and Rim (Front) -
Remove and Install".
b. Remove the front drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Front) -
Remove and Install".
c. Remove the counterweight. Refer to Disassembly and Assembly, "Counterweight - Remove
and Install".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
1/4422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01116913
1. Disconnect hose assembly (2). Repeat for the other side. Remove bolt (1).
Illustration 2 g01116931
2. Install a suitable lifting device to both sides of front axle (3). The weight of front axle (3) is
approximately 408 kg (900 lb).
2/4422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g01116938
3. Remove pin assembly (4). Remove front axle (3).
Note: The flange of pin assembly (4) must be rotated downward in order to clear the frame.
Illustration 4 g01041857
4. Remove seal (5). Use Tooling (A) in order to remove bushing (6). Repeat for the other side.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Sat Nov 30 22:07:19 UTC+0800 2019
3/4422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B
230-7923 Spanner Wrench(1)
1
202-0453 Spanner Wrench As(2)
1
C 246-5254 Spanner Wrench(3)
1
D 2P-8312 Retaining Ring Pliers 1
(1)
Use with spanner nut that as an outside diameter of 120 mm (4.72 inch)
(2)
Use with spanner nut that has an outside diameter of 130 mm (5.12 inch)
(3)
Use with axle that has a retaining ring and pin that locks the spanner nut
Start By:
a. Remove the final drive planetary. Refer to Disassembly and Assembly, "Final Drive Planetary -
Remove".
Illustration 1 g01047618
1. Loosen nut (2). Do not remove nut (2) at this time. Install Tooling (A). Remove tie rod end (1) from
the taper of the knuckle. Remove nut (2) and tie rod end (1).
Note: Follow Step 2 or Step 3 for the correct procedure for the axle that is being serviced.
2/8422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01047569
2. Remove bolts (5) and remove locking plate (4)(if equipped). Use Tooling (B) to remove spanner nut
(3).
3/8422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g01040507
3. Remove retaining ring (4). Remove dowel pin (5). Use Tooling (C) to remove spanner nut (3).
Illustration 4 g01023074
4/8422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 5 g01023075
4. Use a suitable pry bar and push the double U-joint toward the wheel flange. This will make the
removal of retaining ring (8) easier. Use Tooling (D) and remove retaining ring (8). Remove thrust
washer (7) and washer (6).
Illustration 6 g01023088
5. Remove ring gear (9).
5/8422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
14. Illustration 7 g01023126
6. Remove wheel flange (10).
Note: Bearing cone (11) will fall out of wheel flange (10) when wheel flange (10) is removed.
6/8422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 8 g01023130
7. Remove bolts (12). Remove pin assembly (13) and shims (14). Remove bolts (16) and pin assembly
(15).
7/8422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 9 g01023136
8. The weight of knuckle (17) is approximately 50 kg (110 lb). Use two people and remove knuckle
(17).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 30 22:08:14 UTC+0800 2019
8/8422E Backhoe Loader Single Tilt Side Shift Boom HBE00001-UP (MACHINE) POW...
2019/11/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...